Nissan Versa Sedan. Manual — part 652
PWC-30
< DTC/CIRCUIT DIAGNOSIS >
REAR POWER WINDOW SWITCH
REAR POWER WINDOW SWITCH
Component Function Check
INFOID:0000000009269430
1.
CHECK FUNCTION
Check rear power window motor operation with rear power window switch.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009269431
Regarding Wiring Diagram information, refer to
.
1.
CHECK REAR POWER WINDOW SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect rear power window switch connector.
3. Turn ignition switch ON.
4. Check voltage between rear power window switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK REAR POWER WINDOW SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect power window main switch connector.
3. Check continuity between power window main switch harness connector and rear power window switch
harness connector.
4. Check continuity between power window main switch harness connector and ground.
(+)
(-)
Condition
Voltage (V)
(Approx.)
Rear power window switch
Connector
Terminal
LH
D203
3
Ground
Power window main
switch
(rear LH)
NEUTRAL
0
DOWN
Battery voltage
2
NEUTRAL
0
UP
Battery voltage
RH
D303
3
Power window main
switch
(rear RH)
NEUTRAL
0
DOWN
Battery voltage
2
NEUTRAL
0
UP
Battery voltage
Power window main switch
Rear power window switch
Continuity
Connector
Terminal
Connector
Terminal
D7
1
LH
D203
2
Yes
3
3
5
RH
D303
3
7
2
REAR POWER WINDOW SWITCH
PWC-31
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-52, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK REAR POWER WINDOW SWITCH
Check rear power window switch.
PWC-31, "Component Inspection"
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> Replace rear power window switch. Refer to
PWC-54, "Removal and Installation"
Component Inspection
INFOID:0000000009269432
1.
CHECK REAR POWER WINDOW SWITCH
1. Turn ignition switch OFF.
2. Disconnect rear power window switch connector.
3. Check rear power window switch terminals under the following conditions.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace rear power window switch. Refer to
PWC-54, "Removal and Installation"
Power window main switch
Ground
Continuity
Connector
Terminal
D7
1
No
3
5
7
Rear power window switch
Condition
Continuity
Terminal
1
5
UP
Yes
3
4
3
4
NEUTRAL
2
5
1
4
DOWN
2
5
PWC-32
< DTC/CIRCUIT DIAGNOSIS >
POWER WINDOW MOTOR
POWER WINDOW MOTOR
DRIVER SIDE
DRIVER SIDE : Component Function Check
INFOID:0000000009269433
1.
CHECK FUNCTION
Check front power window motor LH operation with power window main switch.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Refer to
PWC-32, "DRIVER SIDE : Diagnosis Procedure"
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000009269434
Regarding Wiring Diagram information, refer to
.
1.
CHECK FRONT POWER WINDOW MOTOR LH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect front power window motor LH connector.
3. Turn ignition switch ON.
4. Check voltage between front power window motor LH harness connector and ground.
Is the inspection result normal?
YES
>> Replace front power window motor LH.
NO
>> GO TO 2.
2.
CHECK FRONT POWER WINDOW MOTOR LH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect power window main switch connector.
3. Check continuity between power window main switch harness connector and front power window motor
LH harness connector.
4. Check continuity between power window main switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-52, "Removal and Installation"
(+)
(-)
Condition
Voltage (V)
(Approx.)
Front power window motor LH
Connector
Terminal
D9
1
Ground
Power window main
switch
NEUTRAL
0
DOWN
Battery voltage
2
NEUTRAL
0
UP
Battery voltage
Power window main switch
Front power window motor LH
Continuity
Connector
Terminal
Connector
Terminal
D7
8
D9
2
Yes
11
1
Power window main switch
Ground
Continuity
Connector
Terminal
D7
8
No
11
POWER WINDOW MOTOR
PWC-33
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
NO
>> Repair or replace harness.
PASSENGER SIDE
PASSENGER SIDE : Component Function Check
INFOID:0000000009269435
1.
CHECK FUNCTION
Check front power window motor RH operation with power window main switch or front power window switch
RH.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Refer to
PWC-33, "PASSENGER SIDE : Diagnosis Procedure"
.
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000009269436
Regarding Wiring Diagram information, refer to
.
1.
CHECK FRONT POWER WINDOW MOTOR RH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect front power window motor RH connector.
3. Turn ignition switch ON.
4. Check voltage between front power window motor RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace front power window motor RH.
NO
>> GO TO 2.
2.
CHECK FRONT POWER WINDOW MOTOR RH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect front power window switch RH connector.
3. Check continuity between front power window switch RH harness connector and front power window
motor RH harness connector.
4. Check continuity between front power window switch RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace front power window switch RH. Refer to
PWC-53, "Removal and Installation"
.
(+)
(-)
Condition
Voltage (V)
(Approx.)
Front power window motor RH
Connector
Terminal
D104
1
Ground
Front power window
switch RH
NEUTRAL
0
UP
Battery voltage
2
NEUTRAL
0
DOWN
Battery voltage
Front power window switch RH
Front power window motor RH
Continuity
Connector
Terminal
Connector
Terminal
D105
6
D104
1
Yes
7
2
Front power window switch RH
Ground
Continuity
Connector
Terminal
D105
6
No
7
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст