Nissan Versa Sedan. Manual — part 440
FAX-12
< REMOVAL AND INSTALLATION >
FRONT WHEEL HUB AND KNUCKLE
3. Remove wheel bearing inner race (outer side) from wheel hub,
using Tools.
4. Remove snap ring from steering knuckle, using suitable tool.
CAUTION:
Do not damage steering knuckle.
5. Remove wheel bearing using Tool from steering knuckle.
ASSEMBLY
1. Install wheel bearing to steering knuckle, using the Tool (A) and
a suitable tool (B).
CAUTION:
• Do not reuse wheel bearing.
• Do not apply a cleaning agent or anticorrosive to the
mounting surface of the wheel bearing of steering
knuckle.
• Install wheel bearing with the wheel sensor rotor rubber
part (C) faced to the steering knuckle inner side.
• The wheel sensor rotor of the wheel bearing must be kept
free of foreign matter.
• The press-fit load must be applied to the wheel bearing outer race and the steering knuckle.
• Do not apply press-fit load to the wheel bearing inner race, the seal (C) on the rubber surface
side (wheel sensor rotor side), and the seal (D) on the metallic surface side. If a press-fit load is
applied, the wheel bearing must be replaced with a new one.
• Wheel bearing press-fit load must be 49 kN (5,000 kg-f, 11,015 lb-f).
2. Install snap ring to steering knuckle.
CAUTION:
• Do not damage the wheel bearing seal.
• The snap ring must be installed evenly into the groove.
3. Press splash guard (1) into the steering knuckle using suitable
tools (A and B).
CAUTION:
Do not reuse splash guard.
Tool number : ST33710000 ( — )
Tool number : ST30031000 ( — )
SDIA0759J
Tool number : ST35321000 ( — )
SDIA0760J
Tool number : ST35271000 ( — )
JPDIF0306ZZ
JSDIA2728ZZ
FRONT WHEEL HUB AND KNUCKLE
FAX-13
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
4. Install wheel hub, using Tools.
CAUTION:
• Do not apply lubricating oil to the press-fit surface of the
wheel hub bearing.
• Set wheel hub and wheel bearing horizontally and insert
them vertically.
• The press-fit load must be applied to the wheel hub and
the wheel bearing inner race.
• Do not apply press-fit load to the steering knuckle and the wheel bearing, the seal. If a press-fit
load is applied, the wheel bearing must be replaced with a new one.
• Apply a press-fit load of 49 kN (5,000 kg-f, 11,015 lb-f) and maintain the loaded state for 30 sec-
onds.
• If the inserted wheel hub is removed again, the wheel bearing must be replaced with a new one.
Inspection
INFOID:0000000009268299
INSPECTION AFTER REMOVAL
Check the following items, and replace the part if necessary.
• Check components for deformation, cracks, and other damage.
• Check boots of transverse link and steering outer socket ball joint for breakage, axial end play, and swing
FSU-6, "Inspection and Adjustment"
INSPECTION AFTER DISASSEMBLY
Wheel Hub
• Check wheel hub for cracks (with magnetic exploration or dye testing). Replace if necessary.
Steering Knuckle
• Check steering knuckle for deformation, cracks, and other damage. Replace if any non-standard conditions
are found.
Snap Rings
• Check snap ring for wear or cracks. Replace if necessary.
INSPECTION AFTER ASSEMBLY
Check wheel bearing rotating torque as per the following instructions.
NOTE:
The adequacy of turning torque can be judged from a measurement value by a spring balancer.
1. For a proper fit of the bearing, turn the wheel hub both clockwise and counterclockwise, respectively, 10
times or more with a press-fit load of 34,300 - 49,000 N (3,500 - 4,998 kg-f, 7,710 - 11,015 lb-f) applied.
2. Set a spring balance on strut mounting hole (upper). Measure
rotating torque at an rpm of 8 - 12 rpm.
• If the turning torque cannot be obtained by the above method,
measure the torque, according to the instructions below.
- Install drive shaft and tighten the hub lock nut to the specified
torque. Rotate the wheel hub to fit properly.
- Set a spring balancer to the hub bolt and measure turning torque
at turning speeds of 8 to 12 rpm.
INSPECTION BEFORE INSTALLATION
Tool number (A) : ST33061000 ( — )
Tool number (B) : ST35321000 ( — )
JPDIF0284ZZ
Rotating torque : Refer to
Spring balance
measurement
: Refer to
Rotating torque
: 0.16 N·m (0.016 kg-m, 1.4 in-lb) or less
Spring balance measurement
: 0.32 N (0.03 kg-f, 0.07 lb-f) or less
SDIA0762J
FAX-14
< REMOVAL AND INSTALLATION >
FRONT WHEEL HUB AND KNUCKLE
Check wheel sensor rotor for foreign matter. Clean the rotor, if necessary.
INSPECTION AFTER INSTALLATION
1. Check wheel sensor harness for proper connection. Refer to
BRC-104, "FRONT WHEEL SENSOR :
.
2. Check the wheel alignment. Refer to
FRONT DRIVE SHAFT
FAX-15
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
FRONT DRIVE SHAFT
Exploded View
INFOID:0000000009268300
Removal and Installation
INFOID:0000000009268301
REMOVAL
1. Remove the wheel and tire assembly using power tool. Refer to
2. Remove wheel sensor and sensor harness. Refer to
BRC-104, "FRONT WHEEL SENSOR : Removal and
.
3. Remove brake lock plate from strut assembly.
4. Remove brake caliper using power tool, leaving brake caliper hydraulic lines connected. Reposition brake
caliper aside with wire. Refer to
BR-36, "BRAKE CALIPER ASSEMBLY : Exploded View"
.
NOTE:
Avoid depressing brake pedal while brake caliper is removed.
5. Put matching marks (A) on disc rotor and wheel hub and bearing
assembly, then remove disc rotor.
CAUTION:
• Put matching marks (A) on the wheel hub and the disc
rotor before removing the disc rotor.
• Do not drop disc rotor.
6. Remove and discard cotter pin, and then loosen wheel hub lock
nut, using Tool (A).
1.
Drive shaft
2.
Cotter pin
A. Apply Molykote M77
AWDIA0951GB
JPDIG0066ZZ
Tool number : KV40104000 ( — )
JSDIA2708ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст