Nissan Versa Sedan. Manual — part 368
PREPARATION
EM-7
< PREPARATION >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Commercial Service Tools
INFOID:0000000009266631
EM03470000
(J-8037)
Piston ring compressor
Installing piston assembly into cylinder bore
ST16610001
(J-23907)
Pulley puller
Removing pilot converter
KV11103000
( — )
Pulley puller
Removing crankshaft pulley
KV11105210
(J-44716)
Stopper plate
Holding drive plate and flywheel static
Tool number
(Kent-Moore No.)
Tool name
Description
S-NT044
S-NT045
NT676
ZZA0009D
Tool name
Description
Power tool
Loosening nuts, screws and bolts
Quick connector release
Removing fuel tube quick connectors in en-
gine room
PIIB1407E
PBIC0198E
EM-8
< PREPARATION >
[HR16DE]
PREPARATION
Spark plug wrench
Removing and installing spark plug
a: 14 mm (0.55 in)
Pulley holder
Crankshaft pulley removing and installing
Valve seat cutter set
Finishing valve seat dimensions
Piston ring expander
Removing and installing piston ring
Valve guide drift
Removing and installing valve guide
Valve guide reamer
(1): Reaming valve guide inner hole
(2): Reaming hole for oversize valve guide
(J-43897-18)
(J-43897-12)
Oxygen sensor thread cleaner
Reconditioning the exhaust system threads
before installing a new air fuel ratio sensor
(Use with anti-seize lubricant shown below.)
A: [18 mm (0.71 in) dia.] for zirconia heated
oxygen sensor
B: [12 mm (0.47 in) dia.] for titania heated
oxygen sensor
C: Mating surface shave cylinder
D: Flutes
Tool name
Description
JPBIA0399ZZ
NT035
S-NT048
S-NT030
PBIC4012E
PBIC4013E
JPBIA0238ZZ
PREPARATION
EM-9
< PREPARATION >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Acoustic tension gauge
Checking drive belt tension
Anti-seize lubricant (Permatex 133AR
or equivalent meeting MIL specifica-
tion MIL-A-907)
Lubricating oxygen sensor thread cleaning
tool when reconditioning exhaust system
threads
Manual lift table caddy
Removing and installing engine
1. Compression gauge
2. Adapter
Checking compression pressure
Tube presser
Pressing the tube of liquid gasket
Tool name
Description
PBIC3881E
AEM489
ZZA1210D
ZZA0008D
S-NT052
EM-10
< BASIC INSPECTION >
[HR16DE]
CAMSHAFT VALVE CLEARANCE
BASIC INSPECTION
CAMSHAFT VALVE CLEARANCE
Inspection and Adjustment
INFOID:0000000009266632
INSPECTION
Perform inspection as follows after removal, replacement or installation of camshaft or valve-related parts, or if
there are unusual engine conditions regarding valve clearance.
1. Remove rocker cover. Refer to
EM-44, "Removal and Installation"
.
2. Measure the valve clearance with the following procedure:
a. Set No. 1 cylinder at TDC of its compression stroke.
• Rotate crankshaft pulley (2) clockwise and align TDC mark (no
paint) (A) to timing indicator (1) on front cover.
• At the same time, check that both intake and exhaust cam
lobes of No. 1 cylinder face inside (
) as shown.
• If the lobes do not face inside, rotate the crankshaft pulley 360
degrees to align as shown.
b. Use a feeler gauge (A) to measure the clearance between the
valve lifter and camshaft.
(B)
: White paint mark (Not used for service)
PBIC3673E
(1)
: Camshaft (INT)
(2)
: Camshaft (EXH)
: Engine front
JPBIA4738ZZ
Valve clearance
: Refer to
.
JPBIA4116ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст