Nissan Versa Sedan. Manual — part 474
FRONT REGULATOR
GW-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
FRONT REGULATOR
Exploded View
INFOID:0000000009267758
Removal and Installation
INFOID:0000000009267759
REMOVAL
1. Remove front door glass. Refer to
GW-21, "Removal and Installation"
2. Disconnect the harness connector from front door power window motor.
3. Remove front door regulator assembly bolts and nuts.
4. Remove front door regulator assembly from front door panel.
INSTALLATION
Installation is in the reverse order of removal.
Disassembly and Assembly
INFOID:0000000009267760
DISASSEMBLY
Remove the power window motor from the regulator assembly.
INSPECTION AFTER REMOVAL
Check the regulator assembly for the following items. Replace or grease it if a malfunction is detected.
1.
Front door panel
2.
Front door lower sash (front)
3.
Front door glass run
4.
Front door sealing screen
5.
Front door power window motor
6.
Front door regulator
7.
Front door glass
8.
Front door lower sash (rear)
9.
Regulator seal (manual window)
10. Snap pin (manual window)
11. Regulator handle (manual window)
AWKIA1881ZZ
GW-24
< REMOVAL AND INSTALLATION >
FRONT REGULATOR
• Wire wear
• Regulator deformation
• The arrows shows the application points of the multi-purpose
grease.
ASSEMBLY
Assembly is in the reverse order of disassembly.
Inspection and Adjustment
INFOID:0000000009267761
FITTING INSPECTION
• Check that the glass fits securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)], and check that the clearance to the
sash is parallel. Loosen the regulator bolts, guide rail bolts, and glass and guide rail bolts to correct the glass
position if the clearance between the glass and sash is not parallel.
JMKIA4453ZZ
REAR DOOR GLASS
GW-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
REAR DOOR GLASS
Exploded View
INFOID:0000000009267762
Removal and Installation
INFOID:0000000009267763
REMOVAL
1. Fully open rear door glass.
2. Remove rear door finisher. Refer to
INT-17, "Removal and Installation"
.
3. Disconnect harness connector from rear door speaker.
4. Remove rear door sealing screen.
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape will remain on the sealing screen, if the sealing
screen is reused.
5. Remove partition sash bolts and screw.
1.
Rear door panel
2.
Sealing screen
3.
Rear door sash
4.
Power window motor
5.
Regulator assembly
6.
Partition sash
7.
Partition glass
8.
Rear door glass
9.
Partition weather-strip
10. Rear door glass run
11. Regulator seal (manual window)
12. Retaining clip (manual window)
13. Regulator handle (manual window)
AWKIA1882ZZ
GW-26
< REMOVAL AND INSTALLATION >
REAR DOOR GLASS
6. Remove partition sash.
• Remove rear door glass run from partition sash.
• Pull partition sash slightly and straight down.
• From the upper side, slope partition sash toward the vehicle and then remove.
7. Operate the rear power window main switch or regulator handle
(manual) to raise or lower the door window until the glass bolts
(A) can be seen.
8. Remove rear door glass bolts.
9. Carefully pulling inward to remove the rear door glass.
10. Remove partition glass.
1. Slide partition glass toward the direction of arrow 1.
2. Pull partition glass toward the direction of arrow 2 to
remove.
3. Remove partition weather strip from the partition glass.
INSTALLATION
Installation is in the reverse order of removal.
Inspection and Adjustment
INFOID:0000000009267764
FITTING INSPECTION
• Check that the glass fits securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)], and check that the clearance to the
sash is parallel. Loosen the regulator bolts, guide rail bolts, and glass and guide rail bolts to correct the glass
position if the clearance between the glass and sash is not parallel.
JMKIA8067ZZ
JMKIA8066ZZ
JMKIA8065ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст