Nissan Versa Sedan. Manual — part 565
MA-18
< PERIODIC MAINTENANCE >
ENGINE MAINTENANCE
10. Remove the Tool from the radiator neck opening.
11. Fill the cooling system reservoir tank to the specified level and install the radiator cap. Run the engine to
warm up the cooling system and top up the system as necessary.
12. Install engine under cover. Refer to
.
ENGINE COOLANT : Flushing Cooling System
INFOID:0000000009269047
1. Install radiator drain plug and reservoir tank, if removed.
CAUTION:
Be sure to clean drain plug and install with new O-ring.
2. If water drain plugs on cylinder block were removed, close and tighten them. Refer to
.
3. Remove air duct from between air cleaner case and electric throttle control actuator. Refer to
4. Disconnect heater hose (1) at location (
) as shown.
•
: Front
• Position heater hose as high as possible.
5. Fill radiator until engine coolant flows out of the disconnected heater hose and then reconnect the heater
hose.
6. Finish filling the engine and reservoir tank with water and reinstall the radiator cap.
7. Install air duct in between air cleaner case and electric throttle control actuator. Refer to
8. Run the engine and warm it up to normal operating temperature.
9. Rev the engine two or three times under no-load.
10. Stop the engine and wait until it cools down.
11. Drain water from the system. Refer to
MA-16, "ENGINE COOLANT : Draining Engine Coolant"
.
12. Repeat steps 1 through 11 until clear water begins to drain from radiator.
FUEL LINES
FUEL LINES : Inspection
INFOID:0000000009269048
Inspect fuel lines, fuel filler cap, and fuel tank for improper attach-
ment, leakage, cracks, damage, loose connections, chafing or dete-
rioration.
If necessary, repair or replace damaged parts.
AIR CLEANER FILTER
Radiator drain plug
: Refer to
JSBIA0616ZZ
(A)
: Engine
(B)
: Fuel line
(C)
: Fuel tank
JPBIA0129ZZ
ENGINE MAINTENANCE
MA-19
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
AIR CLEANER FILTER : Exploded View
INFOID:0000000009269049
AIR CLEANER FILTER : Removal and Installation
INFOID:0000000009269050
REMOVAL
1. Unhook clips (A) and pull the air cleaner cover upward (1).
1.
Clamp
2.
PCV hose
3.
Clamp
4.
Mount rubber
5.
Air duct (inlet)
6.
Air cleaner body
7.
Grommet
8.
Air cleaner filter
9.
Air cleaner cover
10. Mass air flow sensor
11. Air duct
12. Clamp
A.
To electric throttle control actuator
B.
To rocker cover
AWBIA1126ZZ
JSBIA1092ZZ
MA-20
< PERIODIC MAINTENANCE >
ENGINE MAINTENANCE
2. Remove the air cleaner filter (1) from the air cleaner body.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
Check that the air cleaner filter is securely placed in the air cleaner body.
ENGINE OIL
ENGINE OIL : Inspection
INFOID:0000000009269051
ENGINE OIL LEVEL
1. Park vehicle on a level surface, wait 10 minutes before checking the engine oil level.
2. Pull out oil level gauge and wipe it clean.
3. Insert oil level gauge and make sure the engine oil level is within
the range (A) as shown.
4. If it is out of range, adjust it.
ENGINE OIL : Draining
INFOID:0000000009269052
WARNING:
• Be careful not to get burned, as engine oil may be hot.
• Prolonged and repeated contact with used engine oil may cause skin cancer. Try to avoid direct skin
contact with used engine oil. If skin contact is made, wash thoroughly with soap or hand cleaner as
soon as possible.
1. Warm up the engine, park the vehicle on a level surface and check for engine oil leaks. Refer to
2. Stop the engine and wait for 10 minutes.
3. Loosen oil filler cap.
4. Remove drain plug and then drain engine oil.
ENGINE OIL : Refilling
INFOID:0000000009269053
1. Install drain plug with new copper sealing washer. Refer to
CAUTION:
• Be sure to clean drain plug and install new copper sealing washer.
• Do not reuse copper sealing washer.
2. Refill with new engine oil.
CAUTION:
JSBIA1093ZZ
JPBIA0554ZZ
Engine oil capacity and viscosity
: Refer to
ENGINE MAINTENANCE
MA-21
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
• The refill capacity depends on the engine oil temperature and drain time. Use these specifica-
tions for reference only.
• Always use oil level gauge to determine the proper amount of engine oil in the engine.
3. Warm up engine and check area around drain plug and oil filter for engine oil leaks. Repair as necessary.
4. Stop engine and wait for 10 minutes.
5. Check the engine oil level. Refer to
MA-20, "ENGINE OIL : Inspection"
.
OIL FILTER
OIL FILTER : Removal and Installation
INFOID:0000000009269054
REMOVAL
1. Remove engine under cover. Refer to
EXT-19, "Removal and Installation"
.
2. Drain engine oil. Refer to
MA-20, "ENGINE OIL : Draining"
3. Remove oil filter using Tool (A).
: Front
WARNING:
Be careful not to get burned; engine and engine oil may be
hot.
CAUTION:
• When removing, prepare a shop cloth to absorb engine oil
leaks and spills.
• Do not spill engine oil on drive belt.
• Completely wipe off any engine oil that spills on engine
and vehicle.
• Oil filter is provided with relief valve. Use Genuine NISSAN oil filter or equivalent.
INSTALLATION
1. Remove foreign materials adhering to the oil filter installation surface.
2. Apply new engine oil to the oil seal contact surface of new oil fil-
ter.
3. Screw oil filter manually until it touches the installation surface,
then tighten it by 2/3 turn (A), or tighten to specification.
4. Refill engine with new engine oil. Refer to
MA-20, "ENGINE OIL : Refilling"
.
5. Install engine under cover. Refer to
EXT-19, "Removal and Installation"
.
Tool number
: KV10115801 (J-38956)
JSBIA0620ZZ
SMA010
Oil filter
: 17.7 N·m (1.8 kg-m, 13 ft-lb)
JPBIA0077ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст