Nissan Versa Sedan. Manual — part 752
ST-10
< REMOVAL AND INSTALLATION >
STEERING COLUMN
• When removing intermediate shaft, do not insert any tool into the yoke groove to pull out the
intermediate shaft or damage could occur. Replace intermediate shaft with a new one if dam-
aged.
15. Disconnect the harness connectors from EPS control unit.
16. Remove steering column assembly.
17. Remove EPS control unit from steering column assembly. Refer to
STC-40, "Removal and Installation"
.
18. Remove clamp from steering column assembly.
19. Perform inspection after removal. Refer to
INSTALLATION
CAUTION:
• Do not impact on the axis when removing steering column assembly.
• When installing the steering column cover, check that the vehicle harness is not stuck in the cover.
Installation is in the reverse order of removal.
• For intermediate shaft bolt direction, refer to
.
• When connecting intermediate shaft upper side (1) and column
shaft, make sure the bolt is securely seated in groove (A) of col-
umn shaft before final tightening.
• After installing steering column assembly, perform self-diagnosis
with CONSULT to ensure correct operation. Refer to
• Perform inspection after installation. Refer to
.
Inspection
INFOID:0000000009266814
INSPECTION AFTER REMOVAL
• Check each part of steering column assembly for damage or other malfunctions. Replace if there are any
abnormal conditions.
• Measure steering column rotating torque using Tool (A). Replace
steering column assembly if the rotating torque is outside the stan-
dard.
• Measure the steering column length (L) as shown, if vehicle has
been involved in a minor collision. Replace steering column
assembly (with motor, reduction gear, sensor) if (L) is outside the
standard.
INSPECTION AFTER INSTALLATION
• Check each part of steering column assembly for damage or other malfunctions. Replace if there are any
abnormal conditions.
SGIA1295E
Tool number
:
—
(J-25765-A)
Rotating torque
.
JPGIA0085ZZ
Steering column length (L) : Refer to
.
JPGIA0111ZZ
STEERING COLUMN
ST-11
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
• Check the steering wheel play, neutral position steering wheel, steering wheel turning force, and front wheel
turning angle. Refer to
.
• Check tilt mechanism operating range (T) as shown.
Tilt operating range (T)
: Refer to
JPGIA0043ZZ
ST-12
< REMOVAL AND INSTALLATION >
STEERING SHAFT
STEERING SHAFT
Exploded View
INFOID:0000000009266815
Removal and Installation
INFOID:0000000009266816
REMOVAL
CAUTION:
Spiral cable may be cut if steering wheel turns while separating steering column assembly and steer-
ing gear assembly. Be sure to secure steering wheel using string to avoid turning.
1. Set vehicle to the straight-ahead position.
2. Place the steering column tilt to the middle selection.
3. Remove instrument lower panel LH. Refer to
IP-20, "Removal and Installation"
.
4. Loosen lower joint upper bolt.
5. Remove lower joint lower bolt and separate lower joint from steering gear assembly.
CAUTION:
• Place a matching mark on both lower joint and steering gear assembly before removing lower
joint.
• When removing lower joint, do not insert any tool into the yoke groove to pull out the lower joint.
Replace the lower joint with a new one if damaged.
6. Remove lower joint from intermediate shaft.
7. Remove intermediate shaft bolt (steering column side), and remove intermediate shaft from steering col-
umn assembly.
CAUTION:
• Place a matching mark on both intermediate shaft and steering column assembly before remov-
ing intermediate shaft.
• When removing intermediate shaft, do not insert any tool into the yoke groove to pull out the
intermediate shaft or damage could occur. Replace intermediate shaft with a new one if dam-
aged.
INSTALLATION
CAUTION:
Spiral cable may be cut if steering wheel turns while separating steering column assembly and steer-
ing gear assembly. Be sure to secure steering wheel using string to avoid turning.
Installation is in the reverse order of removal.
• Before installation, check that the tilt position is at the middle level.
• For intermediate shaft bolt, and lower joint bolt direction, refer to
1.
Lower joint
2.
Intermediate shaft
3.
Steering column assembly
JPGIA0112GB
STEERING SHAFT
ST-13
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
• To install align the steering gear guide protrusion (A) with the
groove of lower joint (1), make sure the bolt is securely seated in
groove (B) of steering gear before final tightening.
CAUTION:
If a guide protrusion is not included, align with the matching
mark placed at the removal step.
• When tightening lower joint bolt (steering gear assembly side),
temporarily tighten it and make sure there is no sticking or galling
before final tightening.
• When connecting intermediate shaft upper side (1) and column
shaft, make sure the bolt is securely seated in groove (A) of col-
umn shaft before final tightening.
• Perform inspection after installation. Refer to
.
Inspection
INFOID:0000000009266817
INSPECTION AFTER REMOVAL
• Check each part of lower joint for damage or other malfunctions. Replace if there are any abnormal condi-
tions.
• Check each part of intermediate shaft for damage or other malfunctions. Replace if there are any abnormal
conditions.
INSPECTION AFTER INSTALLATION
• Check each part of lower joint for damage or other malfunctions. Replace if there are any abnormal condi-
tions.
• Check each part of intermediate shaft for damage or other malfunctions. Replace if there are any abnormal
conditions.
• Rotate steering wheel to check for decentered condition, binding, noise, or excessive steering effort.
• Check the steering wheel play, neutral position steering wheel, steering wheel turning force, and front wheel
turning angle.
- Steering wheel play: Refer to
- Neutral position steering wheel, steering wheel turning force, and front wheel turning angle: Refer to
JPGIA0041ZZ
SGIA1295E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст