Nissan Versa Sedan. Manual — part 513
INL-48
< DTC/CIRCUIT DIAGNOSIS >
PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT
YES
>> GO TO 3.
NO
>> Repair or replace the harness or connectors.
3.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION POWER SUPPLY SHORT CIRCUIT
Check continuity between BCM connector M98 terminal 90 and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-69, "Removal and Installation"
NO
>> Repair or replace the harness or connectors.
4.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION GROUND CIRCUIT
1. Turn the ignition switch OFF
2. Disconnect push-button ignition switch connector.
3. Check continuity between push-button ignition switch connector M25 terminal 6 and ground.
Is the inspection result normal?
YES
>> Replace push-button ignition switch. Refer to
PCS-100, "Removal and Installation"
.
NO
>> GO TO 5.
5.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION GROUND OPEN CIRCUIT
1. Disconnect BCM connector M98.
2. Check continuity between BCM connector M98 terminal 92 and push-button ignition switch connector
M25 terminal 6.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-69, "Removal and Installation"
NO
>> Repair or replace the harness or connectors.
BCM
Ground
Continuity
Connector
Terminal
M98
90
No
Push-button ignition switch
Ground
Continuity
Connector
Terminal
M25
6
Yes
BCM
Push-button ignition switch
Continuity
Connector
Terminal
Connector
Terminal
M98
92
M25
6
Yes
INTERIOR LIGHTING SYSTEM SYMPTOMS
INL-49
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
SYMPTOM DIAGNOSIS
INTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000009269258
CAUTION:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagno-
sis if any DTC is detected.
Symptom
Possible cause
Inspection item
• Interior room lamp does not turn ON even though the
door is open.
(It turns ON when turning the interior room lamp ON.)
• Interior room lamp does not turn OFF even though
the door is closed.
• Harness between BCM and each
door switch
• Harness between BCM and each
interior room lamp
• BCM
(with Intelligent Key)
(without Intelligent Key).
Interior room lamp control circuit
Refer to
.
Interior room lamp timer does not activate.
(It turns ON/ OFF when the door opens/closes.)
—
Check the interior room lamp setting.
Refer to
(with Intelligent Key)
Interior room lamp battery saver does not activate.
—
Check the interior room lamp battery
saver setting.
Refer to
(with Intelligent Key)
Trunk room lamp does not turn ON even though the
trunk lid is open.
(It turns ON when turning the trunk room lamp ON.)
• Harness between BCM and trunk
room lamp
• Harness between BCM and trunk
lid switch
• BCM
Trunk lid switch circuit
Refer to
(with Intelligent Key)
Trunk room lamp circuit
Refer to
.
INL-50
< REMOVAL AND INSTALLATION >
MAP LAMP
REMOVAL AND INSTALLATION
MAP LAMP
Exploded View
INFOID:0000000009269259
Removal and Installation
INFOID:0000000009269260
WARNING:
Do not touch bulb with your hand while it is on or right after being turned off. Burning may result.
CAUTION:
Do not touch the glass surface of the bulb with bare hands or allow oil or grease to get on it to prevent
damage to the bulb.
REMOVAL
1. Release lens pawls using suitable tool (A) and remove.
CAUTION:
Apply protect tape (B) on suitable tool (A).
: Pawl
2. Release map lamp housing pawl using suitable tool (A).
CAUTION:
Apply protect tape (B) on suitable tool (A).
: Pawl
3. Disconnect the harness connector from map lamp and remove.
1.
Map lamp bulb housing
2.
Bulb
3.
Lens
Pawl
JMLIA1062ZZ
AWLIA1898ZZ
AWLIA1899ZZ
MAP LAMP
INL-51
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
INSTALLATION
Installation is in the reverse order of removal.
Bulb Replacement
INFOID:0000000009269261
WARNING:
Do not touch bulb with your hand while it is on or right after being turned off. Burning may result.
CAUTION:
• Do not touch the glass surface of the bulb with bare hands or allow oil or grease to get on it to pre-
vent damage to the bulb.
• Leaving the bulb removed from housing for a long period of time can deteriorate performance of the
lens and reflector (causing dirt or clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
MAP LAMP BULB
Removal
1. Release lens pawls using suitable tool (A) and remove.
CAUTION:
Apply protect tape (B) on suitable tool (A).
: Pawl
2. Remove the bulb.
Installation
Installation is in the reverse order of removal.
AWLIA1898ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст