Nissan Versa Sedan. Manual — part 95
BR-18
< PERIODIC MAINTENANCE >
REAR DRUM BRAKE
Check inner diameter (B) of the brake drum.
ADJUSTMENT
Burnish contact surfaces between brake drum and brake lining according to the following procedure after
refinishing or replacing brake drum, or if a soft pedal occurs at very low mileage.
CAUTION:
• Be careful of vehicle speed because the brake does not operate firmly/securely until brake drum and
brake lining are securely fitted.
• Only perform this procedure under safe road and traffic conditions. Use extreme caution.
1. Drive vehicle on straight, flat road.
2. Depress brake pedal with the power to stop vehicle within 3 to 5 seconds until the vehicle stops.
3. Drive without depressing brake for a few minutes to cool the brake.
4. Repeat steps 1 to 3 until brake drum and brake lining are securely fitted.
(B)
: Refer to
.
JPFIA0113ZZ
2014 Versa Sedan
BRAKE PEDAL
BR-19
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
REMOVAL AND INSTALLATION
BRAKE PEDAL
Exploded View
INFOID:0000000009267533
NOTE:
CVT and A/T brake pedal assemblies shown, M/T brake pedal assembly similar.
Removal and Installation
INFOID:0000000009267534
REMOVAL
1. Remove instrument lower panel LH. Refer to
IP-20, "Removal and Installation"
2. Disconnect the harness connectors from the stop lamp switch and ASCD cancel switch (if equipped).
3. Disconnect the harness connector from the accelerator pedal.
4. Separate the harness from brake pedal assembly.
5. Rotate the stop lamp switch counter clockwise to remove.
6. Rotate the ASCD cancel switch counter clockwise to remove (if equipped).
7. Remove snap pin and clevis pin from clevis.
CAUTION:
Do not reuse the snap pin and clevis pin.
8. Disconnect the power steering harness connector and position it aside.
9. Remove the brake pedal assembly.
CAUTION:
Hold the brake booster and master cylinder assembly so as not to drop out or contact them other
parts.
10. Disconnect accelerator pedal from brake pedal assembly. Refer to
1.
Clevis pin
2.
Brake pedal assembly
3.
Brake pedal pad
4.
Stop lamp switch
5.
Clip
6.
Snap pin
7.
ASCD cancel switch (if equipped)
AWFIA0875GB
2014 Versa Sedan
BR-20
< REMOVAL AND INSTALLATION >
BRAKE PEDAL
11. Perform inspection after removal. Refer to
BR-20, "Inspection and Adjustment"
.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Do not reuse the snap pin and clevis pin.
• Apply the multi-purpose grease to the clevis pin and the mating faces. (Not necessary if grease has been
already applied)
NOTE:
• The clevis pin may be inserted in either direction.
• Do not give any impact caused by dropping, interference with a tool, contact between parts or with rack to
the brake pedal.
• Do not use an part that has been subject to an impact.
• Perform adjustment after installation. Refer to
BR-20, "Inspection and Adjustment"
.
Inspection and Adjustment
INFOID:0000000009267535
INSPECTION AFTER REMOVAL
• Check the brake pedal for bend, damage, and cracks on the welded parts, and replace the brake pedal
assembly if necessary.
ADJUSTMENT AFTER INSTALLATION
• Adjust each item of brake pedal after installing the brake pedal assembly to the vehicle. Refer to
.
• Perform the release position learning of the accelerator pedal. Refer to
.
2014 Versa Sedan
BRAKE PIPING
BR-21
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
BRAKE PIPING
FRONT
FRONT : Exploded View
INFOID:0000000009267536
AWFIA1066ZZ
2014 Versa Sedan
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст