Nissan Versa Sedan. Manual — part 149
CHG
CHARGING SYSTEM
CHG-27
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SYMPTOM DIAGNOSIS
CHARGING SYSTEM
Symptom Table
INFOID:0000000009269537
Symptom
Reference
Battery discharged
Refer to
CHG-13, "Work Flow (With EXP-800 NI or GR8-1200 NI)"
or
CHG-16, "Work Flow (Without EXP-800 NI or GR8-1200 NI)"
The charge warning lamp does not illuminate when the ignition
switch is set to ON.
The charge warning lamp does not turn OFF after the engine
starts.
The charging warning lamp turns ON when increasing the engine
speed.
CHG-28
< REMOVAL AND INSTALLATION >
GENERATOR
REMOVAL AND INSTALLATION
GENERATOR
Exploded View
INFOID:0000000009269538
Removal and Installation
INFOID:0000000009269539
REMOVAL
1. Disconnect the battery cable from the negative terminal. Refer to
PG-63, "Removal and Installation"
2. Remove fender protector (RH). Refer to
EXT-26, "Removal and Installation"
.
3. Remove the under cover. Refer to
EXT-19, "Removal and Installation"
4. Remove drive belt. Refer to
EM-16, "Removal and Installation"
.
5. Remove the horn bracket.
6. Disconnect the harness connector from the generator.
7. Remove “B” terminal nut and disconnect “B” terminal harness.
8. Remove generator bolts.
9. Remove the generator.
CAUTION:
Be careful not to damage surrounding parts when removing
generator from the vehicle.
NOTE:
Front fascia shown removed for clarity.
10. Remove generator bracket if necessary.
INSTALLATION
1.
Generator bracket bolt
2.
Generator bracket
3.
Generator bolt
4.
Generator
5.
“B” terminal harness
6.
“B” terminal nut
7.
Generator harness connector
JSMIA0093GB
JMMIA0861ZZ
CHG
GENERATOR
CHG-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
1. Install the generator bracket (if removed), using the following
procedure.
a. Temporarily tighten bolt (1).
b. Temporarily tighten bolt (2).
c. Tighten bolts (3) and (4) to specification in numerical order as
shown.
Tighten bolts (1) and (2) to specification.
2. Install generator using the following procedure.
a. Temporarily tighten the generator bolts in order from the lower to the upper.
b. Tighten the generator bolts to the specification starting with the top bolt.
c. Install “B” terminal harness and "B" terminal nut.
CAUTION:
Be sure to tighten "B" terminal nut carefully.
3. Install and check the tension of the drive belt. Refer to
EM-16, "Removal and Installation"
.
4. Installation of the remaining components is in the reverse order of removal.
JMMIA0463ZZ
CHG-30
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Generator
INFOID:0000000009269540
* : Always check with the Parts Department for the latest parts information.
Model*
A002TJ1791ZC
Manufacturer
Mitsubishi
Nominal rating
13.5V - 110A
Ground polarity
Negative
Minimum revolution under no-load
1,000 rpm
Hot output current (When 13.5 V is applied)
More than 27A/1,300 rpm
More than 95A/2,500 rpm
More than 116A/5,000 rpm
Regulated output voltage
14.1 - 14.7V @20
°C (68°F)
Adjustment range of power generation voltage variable control
11.4 - 15.6V
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст