Nissan Versa Sedan. Manual — part 388
ENGINE STAND SETTING
EM-87
< UNIT DISASSEMBLY AND ASSEMBLY >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
3. Drain engine coolant by removing water drain plug (1) from
inside of the engine.
Use Genuine Silicone RTV Sealant or equivalent. Refer to
GI-21, "Recommended Chemical Products and Sealants"
.
: Engine front
Water drain plug
tightening torque
: Refer to
PBIC3742E
EM-88
< UNIT DISASSEMBLY AND ASSEMBLY >
[HR16DE]
ENGINE UNIT
ENGINE UNIT
Disassembly
INFOID:0000000009266672
1. Remove intake manifold. Refer to
2. Remove exhaust manifold. Refer to
.
3. Remove oil pan (lower). Refer to
4. Remove ignition coil, spark plug, and rocker cover. Refer to
5. Remove fuel injector and fuel tube. Refer to
6. Remove front cover and timing chain. Refer to
.
7. Remove camshaft. Refer to
8. Remove cylinder head. Refer to
Assembly
INFOID:0000000009266673
Assembly is in the reverse order of disassembly.
OIL PAN (UPPER) AND OIL STRAINER
EM-89
< UNIT DISASSEMBLY AND ASSEMBLY >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
OIL PAN (UPPER) AND OIL STRAINER
Exploded View
INFOID:0000000009266674
Removal and Installation
INFOID:0000000009266675
NOTE:
The oil strainer is included in the oil pan (upper) and cannot be removed.
REMOVAL
1. Remove the oil pan (lower). Refer to
1.
Rear oil seal
2.
O-ring
3.
Oil pan (upper)
4.
Oil pump chain tensioner (for oil
pump drive chain)
5.
Oil pump drive chain
6.
Crankshaft key
7.
Crankshaft sprocket
8.
Oil pump sprocket
9.
Oil pump
10. O-ring
11. O-ring
12. Oil pan drain plug
13. Drain plug washer
14. Oil pan (lower)
15. Oil filter
16. Connector bolt
17. Oil cooler
18. O-ring
19. Relief valve
A.
Refer to
B.
Refer to
C.
Oil pan (lower) side
AWBIA1477ZZ
EM-90
< UNIT DISASSEMBLY AND ASSEMBLY >
[HR16DE]
OIL PAN (UPPER) AND OIL STRAINER
2. Remove oil pump sprocket and crankshaft sprocket together with oil pump drive chain. Refer to
3. Remove oil pan (upper).
a. Loosen oil pan (upper) bolts in the reverse of the order as
shown.
b. Insert a suitable tool into the arrow (
) as shown and open up a
crack between the oil pan (upper) cylinder block.
c.
Insert the Tool between the oil pan (upper) and cylinder block.
Slide Tool by tapping on the side of Tool with a hammer.
CAUTION:
• Be careful not to damage the mating surface.
• The liquid gasket used at the factory is very strong. Pry only in the areas shown.
• Do not remove oil pump and oil strainer from oil pan (upper).
4. Remove rear oil seal from crankshaft.
INSTALLATION
CAUTION:
Do not reuse O-rings or washers.
1. Install the oil pan (upper):
a. Use scraper to remove old liquid gasket from mating surfaces.
• Also remove the old liquid gasket from mating surface of cylinder block.
• Remove old liquid gasket from the bolt holes and threads.
CAUTION:
Do not scratch or damage the mating surfaces when cleaning off old liquid gasket.
b. Install O-ring to the cylinder block.
: Engine front
JPBIA4199ZZ
: Engine front
Tool number
: KV10111100 (J-37228)
JPBIA4200ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст