Nissan Versa Sedan. Manual — part 910
LOW TIRE PRESSURE WARNING LAMP BLINKS
WT-35
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
LOW TIRE PRESSURE WARNING LAMP BLINKS
Diagnosis Procedure
INFOID:0000000009267474
NOTE:
If low tire pressure warning lamp repeats blinking ON for 2 seconds and OFF for 0.2 seconds, wake-up opera-
tion for all transmitters is not complete.
Carry out transmitter wake-up operation. Refer to
1.
CHECK BCM CONNECTOR
1. Turn ignition switch OFF.
2. Disconnect BCM connectors.
3. Check terminals for damage or loose connections.
Is the inspection result normal?
YES
BCS-69, "Removal and Installation"
or
BCS-122, "Removal and Installa-
.
NO
>> Repair or replace damaged parts.
WT-36
< SYMPTOM DIAGNOSIS >
ID REGISTRATION CANNOT BE COMPLETED
ID REGISTRATION CANNOT BE COMPLETED
Diagnosis Procedure
INFOID:0000000009267475
1.
PERFORM ID REGISTRATION OF ALL TRANSMITTERS
Carry out ID registration of all transmitters. Refer to
.
Can ID registration of all transmitters be completed?
YES
>> Inspection End.
NO
>> Refer to
BCS-26, "AIR PRESSURE MONITOR : CONSULT Function (BCM - AIR PRESSURE
BCS-91, "AIR PRESSURE MONITOR : CONSULT Function (BCM - AIR PRES-
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
WT-37
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000009267476
Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×: Applicable
Reference page
n"
—
—
Re
fer
to
TIRE i
n t
his cha
rt.
Re
fe
r to
ROAD WHEEL
in
th
is ch
art
.
Possible cause and SUSPECTED PARTS
Imp
rop
er i
ns
ta
lla
tio
n,
lo
os
en
es
s
O
ut
-of-ro
un
d
Im
ba
la
nc
e
Incorrect t
ire
pressure
Uneven tire
wear
Def
orm
ati
on
o
r da
ma
ge
No
n-u
n
iformi
ty
In
co
rrec
t t
ire
si
ze
FRONT A
X
LE
AND FRONT SUSP
ENSION
REAR A
X
LE
AND REAR SUSP
ENSION
TI
RE
S
ROAD WHEE
LS
DRIVE SHAFT
BRAKE
STE
E
RING
Symptom
TIRE
Noise
×
×
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
×
×
×
×
×
×
Shudder
×
×
×
×
×
×
×
×
×
×
×
×
Poor quality ride or
handling
×
×
×
×
×
×
×
×
×
×
ROAD
WHEEL
Noise
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
×
Shimmy, Shudder
×
×
×
×
×
×
×
×
×
Poor quality ride or
handling
×
×
×
×
×
×
×
WT-38
< PERIODIC MAINTENANCE >
ROAD WHEEL
PERIODIC MAINTENANCE
ROAD WHEEL
Inspection
INFOID:0000000009267477
ALUMINUM WHEEL
1. Check tires for wear and improper inflation.
2. Check wheels for deformation, cracks and other damage. If deformed, remove wheel and check wheel
runout.
a. Remove tire from aluminum wheel and mount wheel on a balancer machine.
b. Set dial indicator as shown.
c.
Check runout, if runout value exceeds the limit, replace alumi-
num wheel.
STEEL WHEEL
1. Check tires for wear and improper inflation.
2. Check wheels for deformation, cracks and other damage. If deformed, remove wheel and check wheel
runout.
a. Remove tire from steel wheel and mount wheel on a balancer machine.
b. Set two dial indicators as shown.
c.
Set each dial indicator to "0".
d. Rotate wheel and check dial indicators at several points around
the circumference of the wheel.
e. Calculate runout at each point as shown below.
f.
Select maximum positive runout value and the maximum nega-
tive value.
Add the two values to determine total runout.
In case a positive or negative value is not available, use the
maximum value (negative or positive) for total runout.
If the total runout value exceeds the limit, replace steel wheel.
Limit
Lateral Deflection (A)
Refer to
.
Vertical Deflection (B) Refer to
.
SEIA0737E
Lateral deflection (A) = (W+X)/2
Vertical deflection (B) = (Y+Z)/2
Limit
Lateral Deflection (A)
Refer to
.
Vertical Deflection (B) Refer to
.
AWEIA0186ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст