Nissan Versa Sedan. Manual — part 663
RSU-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009267413
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precautions for Suspension
INFOID:0000000009267414
• When installing rubber bushings, the final tightening must be carried out under unladen conditions with tires
on ground. Spilled oil might shorten the life of rubber bushings. Be sure to wipe off any spilled oil.
- Unladen conditions mean that fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and
mats are in designated positions.
• After servicing suspension parts, be sure to check wheel alignment.
• Self-lock nuts are not reusable. Always use new ones when installing. Since new self-lock nuts are pre-oiled,
tighten as they are.
• The tightening surface must be kept free of oil/grease.
• When jacking up the vehicle with a floor jack, do not hang the jack on the suspension beam.
PREPARATION
RSU-3
< PREPARATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
PREPARATION
PREPARATION
Commercial Service Tools
INFOID:0000000009572395
Tool name
Description
Power tool
Loosening nuts, screws and bolts
PIIB1407E
RSU-4
< SYMPTOM DIAGNOSIS >
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000009267415
Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×: Applicable
Reference page
,
,
—
—
,
,
,
,
Possible cause and SUSPECTED PARTS
Im
p
rop
er i
ns
tal
la
tio
n,
loo
sene
ss
S
hoc
k ab
so
rbe
r d
efo
rma
tio
n,
da
ma
ge
o
r de
fle
ct
ion
B
us
hin
g
or m
ou
nt
ing
d
ete
rio
rati
on
P
art
s interference
S
pri
ng
fat
ig
ue
S
us
pe
ns
ion
lo
os
en
es
s
In
co
rrec
t wh
ee
l a
lig
nm
en
t
REA
R
AXLE AND REAR S
U
SPENSION
TI
RE
ROAD W
H
EEL
BR
AK
E
Symptom
Noise
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
×
×
Shudder
×
×
×
×
×
×
×
Poor quality ride or handling
×
×
×
×
×
×
×
×
×
REAR SUSPENSION ASSEMBLY
RSU-5
< PERIODIC MAINTENANCE >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
PERIODIC MAINTENANCE
REAR SUSPENSION ASSEMBLY
On-Vehicle Inspection and Service
INFOID:0000000009267416
Make sure the mounting conditions (looseness, backlash) of each component and component conditions
(wear, damage) are within specifications.
SHOCK ABSORBER INSPECTION
Check shock absorber for oil leakage, damage and replace it if necessary.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст