Nissan Versa Sedan. Manual — part 574
DOOR MIRROR
MIR-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
DOOR MIRROR
Exploded View
INFOID:0000000009269096
DOOR MIRROR ASSEMBLY
DOOR MIRROR ASSEMBLY : Removal and Installation
INFOID:0000000009269097
REMOVAL
CAUTION:
Use the following steps to disengage the door mirror corner cover from the mirror assembly. Other
methods to remove the door mirror corner cover may damage the pawls.
1. Remove door mirror corner cover.
a. Fully open door window.
b. Apply protective tape where the door mirror corner cover con-
tacts the front door finisher.
1.
Door mirror rear finisher
2.
Door mirror glass
3.
Door mirror corner cover
4.
Front door corner finisher
5.
Door mirror assembly
Pawl
JMLIA2085GB
JMLIA2087ZZ
MIR-16
< REMOVAL AND INSTALLATION >
DOOR MIRROR
c.
Hold pawl (A) so it may not be pulled outward, then pull the front
end of the mirror corner cover outward to disengage pawl (B).
: Pawl
CAUTION:
Hold pawl (A) so that it will not be pulled outward or pawl
(A) will be damaged.
d. Slide door mirror corner cover slightly upward and disengage
pawl (B), while holding pawl (A) so that it may not be pulled out-
ward.
: Pawl
CAUTION:
Hold pawl (A) so that it will not be pulled outward or pawl
(A) will be damaged.
e. While holding pawl (A) and slightly opening lower portion of door
mirror corner cover, disengage pawl (A) from front door panel.
: Pawl
CAUTION:
• Do not pull pawl (A) outward. Pawl (A) will be damaged if it
is pulled outward.
• Be careful to remove, visually checking the engagement
status of pawl (A) from clearance between door panel and
door mirror corner cover, as indicated by the arrow (D).
f.
While slightly lifting lower portion of door mirror corner cover,
slowly tilt door mirror corner cover upward as indicated by the
arrow (1). Pull front end forward as indicated by the arrow (2)
and remove door mirror corner cover.
CAUTION:
During removal, visually check the engagement status of
pawl from clearance between door panel and door mirror
corner cover.
2. Remove front door finisher. Refer to
INT-15, "Removal and Installation"
3. Disconnect the harness connector from the door mirror.
4. Remove door mirror nuts and the door mirror assembly.
INSTALLATION
Installation is in the reverse order or removal.
CAUTION:
• When installing, check visually door mirror corner cover pawls. Install a new door mirror corner
cover if they have been damaged.
• When installing door mirror corner cover, check that pawls are securely fitted in door panel, then
press pawls in.
JMLIA2088ZZ
JMLIA2089ZZ
JMLIA1605ZZ
JMLIA1606ZZ
DOOR MIRROR
MIR-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
FRONT DOOR CORNER FINISHER
FRONT DOOR CORNER FINISHER : Removal and Installation
INFOID:0000000009269098
REMOVAL
1. Apply protective tape (A) on the door panel. Disengage the
pawls and remove front door corner finisher using a suitable tool
(B).
: Pawl
INSTALLATION
Installation is in the reverse order or removal.
• Inspect front door corner finisher pawls for damage, install new pawls (if necessary).
• Align front door corner finisher to pawls and press pawls in securely.
ALLIA1039ZZ
MIR-18
< REMOVAL AND INSTALLATION >
DOOR MIRROR GLASS
DOOR MIRROR GLASS
Removal and Installation
INFOID:0000000009269099
REMOVAL
1. Place a piece of protective tape on the mirror housing.
2. Tilt the door mirror glass upward (1).
3. Remove the door mirror glass lower side, using a suitable tool
(A) in the recess between door mirror glass (1) and actuator (2)
and push up on pawls and rotate (twist).
4. Disconnect harness connector from door mirror glass (if equipped with heated mirrors).
5. Remove the glass using a suitable tool in the (LH/RH) recesses
between door mirror glass and actuator and push up on pawls
and rotate (twist).
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
After installation, visually check that pawls are securely engaged.
ALLIA1036ZZ
ALLIA1037ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст