Nissan Versa Sedan. Manual — part 495
BLOWER FAN ON SIGNAL
HAC-35
< DTC/CIRCUIT DIAGNOSIS >
[MANUAL AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
BLOWER FAN ON SIGNAL
Component Function Check
INFOID:0000000009269796
1.
CHECK BLOWER FAN ON SIGNAL
With CONSULT
1. Turn ignition switch ON.
2. Select “AIR CONDITIONER” of “BCM” using CONSULT.
3. Select “FAN ON SIG” in “DATA MONITOR” mode, and check status under the following condition.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Refer to
Diagnosis Procedure
INFOID:0000000009269797
Regarding Wiring Diagram information, refer to
.
1.
CHECK BLOWER FAN ON SIGNAL
1. Turn ignition switch OFF.
2. Disconnect front air control harness connector.
3. Turn ignition switch ON.
4. Check output waveform between front air control and ground with using oscilloscope.
Is the inspection result normal?
YES
>> Replace front air control. Refer to
HAC-48, "Removal and Installation"
.
NO
>> GO TO 2.
2.
CHECK BLOWER FAN ON SIGNAL CIRCUIT FOR OPEN
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity front air control harness connector and BCM harness connector.
Monitor item
Condition
Status
FAN ON SIG
Fan control dial
Except OFF position
On
OFF position
Off
+
−
Output waveform
Front air control
Connector
Terminal
M33
5
Ground
PKIB4960J
Front air control
BCM
Continuity
Connector
Terminal
Connector
Terminal
M33
5
M18 (without Intelligent Key system)
28
Yes
M97 (with Intelligent Key system)
HAC-36
< DTC/CIRCUIT DIAGNOSIS >
[MANUAL AIR CONDITIONING]
BLOWER FAN ON SIGNAL
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK BLOWER FAN ON SIGNAL CIRCUIT FOR SHORT
Check continuity between front air control harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-69, "Removal and Installation"
or
BCS-122, "Removal and Installa-
.
NO
>> Repair harness or connector.
Front air control
—
Continuity
Connector
Terminal
M33
5
Ground
No
A/C INDICATOR
HAC-37
< DTC/CIRCUIT DIAGNOSIS >
[MANUAL AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
A/C INDICATOR
Diagnosis Procedure
INFOID:0000000009269798
Regarding Wiring Diagram information, refer to
.
1.
CHECK A/C INDICATOR POWER SUPPLY
1. Turn ignition switch ON.
2. Check voltage between front air control harness connector and ground.
Is the inspection result normal?
YES
>> Replace front air control. Refer to
HAC-48, "Removal and Installation"
.
NO
>> Repair harness or connector between front air control and fuse.
+
−
Voltage (V)
(Approx.)
Front air control
Connector
Terminal
M33
15
Ground
Battery voltage
HAC-38
< DTC/CIRCUIT DIAGNOSIS >
[MANUAL AIR CONDITIONING]
FRONT BLOWER MOTOR
FRONT BLOWER MOTOR
Description
INFOID:0000000009269799
The front blower motor utilizes a brush-less motor with a rotating magnet. Quietness is improved over previous
motors where the brush was the point of contact and the coil rotated.
Diagnosis Procedure
INFOID:0000000009269800
Regarding Wiring Diagram information, refer to
.
1.
CHECK SYMPTOM
Check symptom (A or B).
Which symptom is detected?
A
>> GO TO 2.
B
>> GO TO 7.
2.
CHECK FUSE
1. Turn ignition switch OFF.
2. Check 15A fuses (Nos. 20 and 22, located in fuse block (J/B)].
NOTE:
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace the blown fuse after repairing the affected circuit.
3.
CHECK FRONT BLOWER MOTOR POWER SUPPLY
1. Disconnect front blower motor connector.
2. Turn ignition switch ON.
3. Check voltage between front blower motor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
CHECK BLOWER RELAY
1. Turn ignition switch OFF.
2. Check blower relay. Refer to
HAC-40, "Component Inspection (Blower Relay)"
.
Is the inspection result normal?
YES
>> Repair harness or connector between front blower motor and fuse.
NO
>> Replace blower relay.
5.
CHECK FAN SWITCH GROUND CIRCUIT FOR OPEN
1. Turn ignition switch OFF.
Symptom
A
Front blower motor does not operate at any dial position
B
Front blower motor does not operate at any dial position other than 4th,
or operation speed is not normal.
+
−
Voltage (V)
(Approx.)
Front blower motor
Connector
Terminal
M62
1
Ground
Battery voltage
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст