Nissan Versa Sedan. Manual — part 10
AV-32
< REMOVAL AND INSTALLATION >
[BASE AUDIO]
ANTENNA FEEDER
ANTENNA FEEDER
Feeder Layout
INFOID:0000000009266714
AWNIA2457ZZ
1.
Antenna mast
2.
Antenna feed
3.
Clip
4.
Harness connector
5.
Audio unit
6.
Harness connector
AV
PRECAUTIONS
AV-33
< PRECAUTION >
[MID AUDIO]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009266715
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Work
INFOID:0000000009266716
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty
area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
AV-34
< PREPARATION >
[MID AUDIO]
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000009266717
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000009266718
Tool number
(Kent-Moore No.)
Tool name
Description
—
(J-46534)
Trim Tool Set
Removing trim components
AWJIA0483ZZ
Tool name
Description
Power tool
Loosening nuts, screws and bolts
PIIB1407E
AV
COMPONENT PARTS
AV-35
< SYSTEM DESCRIPTION >
[MID AUDIO]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000009375100
Component Description
INFOID:0000000009375101
1.
Rod antenna
2.
Antenna base (antenna amp.)
3.
Rear door speaker RH
4.
Front door speaker RH
5.
Front door speaker LH
6.
Rear door speaker LH
7.
Microphone
8.
Steering wheel audio control switches 9.
Audio unit
10. Bluetooth
®
control unit (view with lug-
gage side lower finisher RH removed)
11. Bluetooth
®
antenna (view with lug-
gage side lower finisher RH removed)
AWNIA3041ZZ
Part name
Description
Audio unit
• Controls audio system functions
• Inputs amplified AM/FM radio signal from antenna amp.
• Inputs vehicle speed signal from combination meter
• Inputs hands-free phone functions from Bluetooth
®
control unit
• Outputs sound signals to front and rear door speakers
Front door speakers
• Outputs sound signal from audio unit
• Outputs high, mid and low-range sounds
Rear door speakers
Bluetooth
®
control unit
• Controls hands-free phone and audio system functions
• Inputs steering switch signal
• Inputs microphone voice signal
• Outputs steering switch signal to audio unit
• Outputs hands-free phone functions to audio unit
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст