Nissan Versa Sedan. Manual — part 705
SEC-92
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B210C STARTER CONTROL RELAY
NO
>> Replace IPDM E/R. Refer to
B210D STARTER RELAY
SEC-93
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B210D STARTER RELAY
DTC Logic
INFOID:0000000009268442
DTC DETECTION LOGIC
NOTE:
If DTC B210D is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Press push-button ignition switch under the following conditions to start engine, and wait 1 second or
more.
-
Selector lever: In the P position
-
Brake pedal: Not depressed
2. Check DTC in Self Diagnostic Result mode of IPDM E/R using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> Inspection End
Diagnosis Procedure
INFOID:0000000009268443
Regarding Wiring Diagram information, refer to
.
1.
CHECK STARTER RELAY POWER SUPPLY CIRCUIT
1. Turn ignition switch ON.
2. Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK STARTER RELAY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect starter relay.
3. Disconnect BCM connector.
4. Check continuity between starter relay harness connector and BCM harness connector.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B210D
STARTER RELAY ON
When comparing the following items, IPDM
E/R detects that starter relay is stuck in the
ON position for 1 second or more.
• Starter control relay signal (CAN) from
BCM
• Starter relay status signal (CAN) from BCM
• Starter control relay and starter relay status
signal (IPDM E/R input)
• Starter control relay control signal (IPDM E/
R output)
• Transmission range switch signal input
• Harness or connectors
(The CAN communication line is
open or shorted.)
• Harness or connectors
(Starter relay circuit is open or
shorted.)
• IPDM E/R
• BCM
• Starter relay
(+)
(–)
Condition
Voltage (V)
(Approx.)
BCM
Connector
Terminal
M98
97
Ground
CVT selector lever
N or P position
Battery voltage
Other than above
0
SEC-94
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B210D STARTER RELAY
5. Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-30, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK STARTER RELAY
SEC-94, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace starter relay.
4.
REPLACE BCM
1. Replace BCM. Refer to
BCS-69, "Removal and Installation"
.
2. Perform initialization of BCM and registration of all Intelligent keys using CONSULT.
3. Perform DTC CONFIRMATION PROCEDURE for DTC B210D. Refer to
.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace IPDM E/R. Refer to
PCS-30, "Removal and Installation"
Component Inspection
INFOID:0000000009268444
1.
CHECK STARTER RELAY
1. Turn ignition switch OFF.
2. Disconnect starter relay.
3. Check continuity between starter relay terminals.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace starter relay.
Starter relay
BCM
Continuity
Connector
Terminal
Connector
Terminal
E41
1
M98
97
Yes
Starter relay
Ground
Continuity
Connector
Terminal
E41
1
No
Starter relay
Condition
Continuity
Terminal
3
5
12 V direct current supply between terminals 1 and 2
Yes
No current supply
No
B210E STARTER RELAY
SEC-95
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B210E STARTER RELAY
DTC Logic
INFOID:0000000009268445
DTC DETECTION LOGIC
NOTE:
• If DTC B210E is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B210E is displayed with DTC B2605, first perform the trouble diagnosis for DTC B2605. Refer to
• When IPDM E/R power supply voltage is low (Approx. 7 - 8 V for about 1 second), the DTC B210F may be
detected.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Press push-button ignition switch under the following conditions to start engine, and wait 1 second or
more.
-
Selector lever: In the P position
-
Brake pedal: Not depressed
2. Check DTC in Self Diagnostic Result mode of IPDM E/R using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009268446
Regarding Wiring Diagram information, refer to
.
1.
CHECK STARTER RELAY OUTPUT SIGNAL
1. Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK STARTER RELAY OUTPUT SIGNAL CIRCUIT
1. Turn ignition switch OFF.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B210E
STARTER RELAY OFF
When comparing the following items, IPDM E/R
detects that starter relay is stuck in the OFF po-
sition for 1 second or more.
• Starter control relay signal (CAN) from BCM
• Starter relay status signal (CAN) from BCM
• Starter control relay and starter relay status
signal (IPDM E/R input)
• Starter control relay control signal (IPDM E/R
output)
• Transmission range switch signal input
• Harness or connectors
(The CAN communication line is open
or shorted.)
• Harness or connector
(Starter relay circuit is open or shorted.)
• IPDM E/R
• Battery
• BCM
• Starter relay
(+)
(–)
Condition
Voltage (V)
(Approx.)
BCM
Connector
Terminal
M98
97
Ground
CVT shift selector lever
N or P position
Battery voltage
Other than above
0
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст