Nissan Versa Sedan. Manual — part 296
P0102, P0103 MAF SENSOR
EC-183
< DTC/CIRCUIT DIAGNOSIS >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0102, P0103 MAF SENSOR
DTC Logic
INFOID:0000000009267080
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
Which DTC is detected?
P0102 >> GO TO 2.
P0103 >> GO TO 3.
2.
PERFORM DTC CONFIRMATION PROCEDURE FOR DTC P0102
1. Start engine and wait at least 5 seconds.
2. Check DTC.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
3.
PERFORM DTC CONFIRMATION PROCEDURE FOR DTC P0103-I
1. Turn ignition switch ON and wait at least 5 seconds.
2. Check DTC.
Is DTC detected?
YES
>> Go to
NO
>> GO TO 4.
4.
PERFORM DTC CONFIRMATION PROCEDURE FOR DTC P0103-II
1. Start engine and wait at least 5 seconds.
2. Check DTC.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009267081
1.
INSPECTION START
Confirm the detected DTC.
Which DTC is detected?
P0102 >> GO TO 2.
P0103 >> GO TO 3.
2.
CHECK INTAKE SYSTEM
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0102
Mass air flow sensor circuit
low input
An excessively low voltage from the sensor is
sent to ECM.
• Harness or connectors
(The sensor circuit is open or shorted.)
• Intake air leakage
• Mass air flow sensor
P0103
Mass air flow sensor circuit
high input
An excessively high voltage from the sensor is
sent to ECM.
• Harness or connectors
(The sensor circuit is open or shorted.)
• Mass air flow sensor
EC-184
< DTC/CIRCUIT DIAGNOSIS >
[HR16DE]
P0102, P0103 MAF SENSOR
Check the following for connection.
• Air duct
• Vacuum hoses
• Intake air passage between air duct to intake manifold
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Reconnect the parts.
3.
CHECK GROUND CONNECTION
1. Turn ignition switch OFF.
2. Check ground connection E15. Refer to Ground Inspection in
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace ground connection.
4.
CHECK MAF SENSOR POWER SUPPLY CIRCUIT
1. Disconnect mass air flow (MAF) sensor harness connector.
2. Turn ignition switch ON.
3. Check the voltage between MAF sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair open circuit or short to ground or short to power in harness or connectors.
5.
CHECK MAF SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between MAF sensor harness connector and ECM harness connector.
4. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair open circuit or short to ground or short to power in harness or connectors.
6.
CHECK MAF SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1. Check the continuity between MAF sensor harness connector and ECM harness connector.
2. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair open circuit or short to ground or short to power in harness or connectors.
7.
CHECK MASS AIR FLOW SENSOR
EC-185, "Component Inspection"
Is the inspection result normal?
MAF sensor
Ground
Voltage
Connector
Terminal
F31
2
Ground
Battery voltage
MAF sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
F31
3
F11
52
Existed
MAF sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
F31
4
F11
45
Existed
P0102, P0103 MAF SENSOR
EC-185
< DTC/CIRCUIT DIAGNOSIS >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
YES
>> GO TO 8.
NO
>> Replace mass air flow sensor. Refer to
EM-25, "Removal and Installation"
.
8.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000009620008
1.
CHECK MASS AIR FLOW SENSOR-I
With CONSULT
1. Turn ignition switch OFF.
2. Reconnect all harness connectors disconnected.
3. Start engine and warm it up to normal operating temperature.
4. Connect CONSULT and select “DATA MONITOR” mode of “ENGINE”.
5. Select “MAS A/F SE-B1” and check indication.
*: Check for linear voltage rise in response to engine being increased to about 4,000 rpm.
Without CONSULT
1. Turn ignition switch OFF.
2. Reconnect all harness connectors disconnected.
3. Start engine and warm it up to normal operating temperature.
4. Check the voltage between ECM harness connector and ground.
*: Check for linear voltage rise in response to engine being increased to about 4,000 rpm.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK FOR THE CAUSE OF UNEVEN AIR FLOW THROUGH MASS AIR FLOW SENSOR
1. Turn ignition switch OFF.
2. Check for the cause of uneven air flow through mass air flow sensor. Refer to the following.
-
Crushed air ducts
-
Malfunctioning seal of air cleaner element
-
Uneven dirt of air cleaner element
-
Improper specification of intake air system parts
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 3.
3.
CHECK MASS AIR FLOW SENSOR-II
Monitor item
Condition
MAS A/F SE-B1
MAS A/F SE-B1
Ignition switch ON (Engine stopped.)
Approx. 0.4 V
Idle (Engine is warmed-up to normal operating temperature.)
0.8 - 1.3 V
2,500 rpm (Engine is warmed-up to normal operating temperature.)
1.4 - 1.9 V
Idle to about 4,000 rpm
0.8 - 1.3 V to Approx. 4.3 V*
ECM
Condition
Voltage
Connector
+
−
Terminal
F11
45
52
Ignition switch ON (Engine stopped.)
Approx. 0.4 V
Idle (Engine is warmed-up to normal operating temperature.)
0.8 - 1.3 V
2,500 rpm (Engine is warmed-up to normal operating temperature.)
1.4 - 1.9 V
Idle to about 4,000 rpm
0.8 - 1.3 V to Approx. 4.3 V*
EC-186
< DTC/CIRCUIT DIAGNOSIS >
[HR16DE]
P0102, P0103 MAF SENSOR
With CONSULT
1. Repair or replace malfunctioning part.
2. Start engine and warm it up to normal operating temperature.
3. Connect CONSULT and select “DATA MONITOR” mode of “ENGINE”.
4. Select “MAS A/F SE-B1” and check indication.
*: Check for linear voltage rise in response to engine being increased to about 4,000 rpm.
Without CONSULT
1. Repair or replace malfunctioning part.
2. Start engine and warm it up to normal operating temperature.
3. Check the voltage between ECM harness connector and ground.
*: Check for linear voltage rise in response to engine being increased to about 4,000 rpm.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 4.
4.
CHECK MASS AIR FLOW SENSOR-III
With CONSULT
1. Turn ignition switch OFF.
2. Disconnect mass air flow sensor harness connector and reconnect it again.
3. Start engine and warm it up to normal operating temperature.
4. Connect CONSULT and select “DATA MONITOR” mode of “ENGINE”.
5. Select “MAS A/F SE-B1” and check indication.
*: Check for linear voltage rise in response to engine being increased to about 4,000 rpm.
Without CONSULT
1. Turn ignition switch OFF.
2. Disconnect mass air flow sensor harness connector and reconnect it again.
3. Start engine and warm it up to normal operating temperature.
4. Check the voltage between ECM harness connector and ground.
Monitor item
Condition
MAS A/F SE-B1
MAS A/F SE-B1
Ignition switch ON (Engine stopped.)
Approx. 0.4 V
Idle (Engine is warmed-up to normal operating temperature.)
0.8 - 1.3 V
2,500 rpm (Engine is warmed-up to normal operating temperature.)
1.4 - 1.9 V
Idle to about 4,000 rpm
0.8 - 1.3 V to Approx. 4.3 V*
ECM
Condition
Voltage
Connector
+
−
Terminal
F11
45
52
Ignition switch ON (Engine stopped.)
Approx. 0.4 V
Idle (Engine is warmed-up to normal operating temperature.)
0.8 - 1.3 V
2,500 rpm (Engine is warmed-up to normal operating temperature.)
1.4 - 1.9 V
Idle to about 4,000 rpm
0.8 - 1.3 V to Approx. 4.3 V*
Monitor item
Condition
MAS A/F SE-B1
MAS A/F SE-B1
Ignition switch ON (Engine stopped.)
Approx. 0.4 V
Idle (Engine is warmed-up to normal operating temperature.)
0.8 - 1.3 V
2,500 rpm (Engine is warmed-up to normal operating temperature.)
1.4 - 1.9 V
Idle to about 4,000 rpm
0.8 - 1.3 V to Approx. 4.3 V*
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст