Nissan Versa Sedan. Manual — part 246
DLK-302
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
FRONT DOOR LOCK
Exploded View
INFOID:0000000009269010
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000009269011
REMOVAL
1. Remove inside handle. Refer to
DLK-303, "INSIDE HANDLE : Removal and Installation"
.
2. Remove outside handle. Refer to
DLK-304, "OUTSIDE HANDLE : Removal and Installation"
.
3. Disconnect the harness connector from door lock actuator (if equipped).
4. Remove front door lower sash (rear). Refer to
.
5. Remove door lock assembly bolts and door lock assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse door lock assembly bolt. Always replace it with a new one when it is removed.
• After installation, check door open/close, lock/unlock operation.
• Check door lock cable is properly engaged with outside handle bracket.
1.
Door key cylinder assembly (driver
side)
Outside handle escutcheon (passen-
ger side)
2.
Rear gasket
3.
Outside handle bracket
4.
Bolt
5.
Door key cylinder rod (driver side)
6.
Door lock assembly
7.
Inside handle
8.
Outside handle
9.
Front gasket
10. Clip
Pawl Front
JMKIA8160GB
FRONT DOOR LOCK
DLK-303
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• Check door lock assembly for poor lubrication. Apply a suit-
able multi-purpose grease to door lock if necessary.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000009269012
REMOVAL
1. Remove front door finisher. Refer to
INT-15, "Removal and Installation"
2. Remove upper side of sealing screen.
NOTE:
Cut the butyl tape so that some parts of the butyl tape remain on the sealing screen, if the sealing screen
is reused.
3. Release lock knob cable (2) and inside handle cable (3) from
clip (1).
4. Remove inside handle bolt.
5. Release inside handle (1) from door panel (2) by sliding toward
vehicle rear and separating.
: Pawl
: Front
6. Disengage inside handle cable (3) and lock knob cable (2), and
remove inside handle (1).
JMKIA8077ZZ
JMKIA8078ZZ
JMKIA8079ZZ
JMKIA5885ZZ
DLK-304
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check door open/close, lock/unlock operation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000009269013
REMOVAL
1. Fully close the front door glass.
2. Remove front door finisher. Refer to
INT-15, "Removal and Installation"
3. Remove sealing screen.
NOTE:
Cut the butyl tape so that some parts of the butyl tape remain on the sealing screen, if the sealing screen
is reused.
4. For drivers side only, open rod holder (1) by pulling downward
and separate key rod (3) from door lock assembly (2).
5. Disengage outside handle cable (1) from cable clip (2).
: Front
6. Remove door side grommet (1), and loosen bolt from grommet
hole (2).
JMKIA8080ZZ
JMKIA8081ZZ
JMKIA5888ZZ
FRONT DOOR LOCK
DLK-305
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
7. While pulling outside handle, remove door key cylinder assem-
bly (LH side) or outside handle escutcheon (RH side).
8. While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.
9. Remove front gasket (1) and rear gasket (2).
: Front
10. Slide outside handle bracket toward rear of vehicle to remove.
: Front
11. Disconnect outside handle cable (1) from outside handle bracket
(2) as shown.
JMKIA0560ZZ
JMKIA0524ZZ
JMKIA5889ZZ
JMKIA5890ZZ
JMKIA5891ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст