Nissan Versa Sedan. Manual — part 881
TM-430
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
CVT SHIFT SELECTOR
• When connecting the control cable (1) to the CVT shift selector
assembly (2), face the grooved surface of the rib (A) up and insert
the control cable until it stops.
Disassembly and Assembly
INFOID:0000000009268243
DISASSEMBLY
1. Slide the shift selector handle cover (1) down.
CAUTION:
Do not damage the shift selector handle cover.
2. Pull out the lock pin (2).
3. Pull the shift selector handle (3) and shift selector handle cover
upward to remove.
4. Remove the position lamp.
5. Disengage the hooks (A) (4 locations), and lift up the position
indication panel (1) to separate it from the CVT shift selector
assembly (2).
CAUTION:
Do not damage the CVT shift selector assembly.
ASSEMBLY
Assembly is in the reverse order of disassembly.
• Follow the procedure below to install the shift selector handle.
1. Install the lock pin (2) onto the shift selector handle (3).
2. Install the shift selector handle cover (1) onto the shift selector
handle.
3. Press the shift selector handle onto the shift selector until it
clicks.
CAUTION:
• When pressing the shift selector handle onto the shift
selector, do not press the shift selector handle button.
• Do not strike the shift selector handle to install it.
Inspection and Adjustment
INFOID:0000000009268244
INSPECTION
JSDIA1624ZZ
JSDIA1796ZZ
ALDIA0264ZZ
JSDIA1796ZZ
CVT SHIFT SELECTOR
TM-431
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
1. Turn ON the ignition switch with the shift selector in the "P" position.
2. Press the shift selector handle button with the brake pedal depressed, and confirm that the shift selector
can be moved from the "P" position. Also confirm that shift selector will not move from the "P" position
without depressing the brake pedal.
3. Move the shift selector and check for “excessive effort,” “sticking,” “noise” or “rattle”.
4. Confirm that shift selector stops at each position with the feel of engagement when it is moved through all
the positions. Check whether or not the actual position the shift selector is in matches the position shown
by the transaxle body.
5. The method of operating the shift selector to individual positions
correctly should be as shown.
• (A): Press shift selector button to operate shift selector, while
depressing the brake pedal.
• (B): Press shift selector button to operate shift selector.
• (C): Shift selector can be operated without pressing shift
selector button.
6. When the shift selector handle button is pressed without apply-
ing forward/backward force to the shift selector at “P”, “R”, “N”
and “D” positions, there should be no “sticking” of the button.
7. Confirm the back-up lamps illuminate only when shift selector is
placed in the “R” position. Confirm the back-up lamps do not illu-
minate when the shift selector is pushed toward the “R” position side when shift selector is in the “P” or “N”
position.
8. Check that the engine can be started only when the shift selector is in the “P” and “N” positions.
9. Check that the transaxle is locked when the shift selector is in the "P" position.
ADJUSTMENT
1. Move the shift selector to the “P” position.
CAUTION:
Rotate the wheels at least a quarter turn and be certain the transaxle is locked in the "P" position.
2. Remove nut (A) and set manual lever (B) to the “P” position.
CAUTION:
Do not apply force to the manual lever.
3. Tighten nuts to the specified torque. Refer to
.
CAUTION:
Do not move the manual lever when tightening.
WCIA0620E
JSDIA1875ZZ
TM-432
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
CONTROL CABLE
CONTROL CABLE
Exploded View
INFOID:0000000009268245
Removal and Installation
INFOID:0000000009268246
CAUTION:
Always apply the parking brake before performing removal and installation.
REMOVAL
1. Remove the battery. Refer to
PG-63, "Removal and Installation"
2. Remove the TCM and bracket. Refer to
TM-437, "Removal and Installation"
.
3. Remove the IPDM E/R. Refer to
PCS-56, "Removal and Installation"
.
4. Remove the battery tray and bracket.
5. Remove the center console. Refer to
IP-23, "Removal and Installation"
.
6. Remove the control cable from the CVT shift selector assembly.
7. Disengage the pawls (B) of the grommet (A), and pull downward
to remove.
8. Remove the control cable nut from the manual lever.
1.
Bracket B
2.
Lock plate
3.
Transaxle assembly
4.
Bracket A
5.
Control cable
6.
CVT shift selector assembly
A: Manual lever
B: Grommet
JSDIA1921GB
JSDIA1809ZZ
CONTROL CABLE
TM-433
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
9. Remove the lock plate (1).
10. Lift up the heat plate.
11. Remove the control cable (1) from the bracket (2).
12. Remove the control cable from the vehicle.
13. Remove bracket.
INSTALLATION
Installation is in the reverse order of removal.
• From below the vehicle, press the grommet (A) into place until the
pawls (B) make a click sound.
CAUTION:
Check that pulling down on the grommet does not disconnect
it.
• Pay attention to the following when connecting the control cable to the CVT shift selector.
1. When connecting the control cable (1) to the CVT shift selector
assembly (2), face the grooved surface of the rib (A) up and
insert the control cable until it stops.
JSDIA1812ZZ
Front
JPDIA0107ZZ
JSDIA1809ZZ
JSDIA1624ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст