Nissan Versa Sedan. Manual — part 330
P0456 EVAP CONTROL SYSTEM
EC-319
< DTC/CIRCUIT DIAGNOSIS >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
2. Check for genuine NISSAN fuel filler cap design.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace with genuine NISSAN fuel filler cap.
2.
CHECK FUEL FILLER CAP INSTALLATION
Check that the cap is tightened properly by rotating the cap clockwise.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Open fuel filler cap, then clean cap and fuel filler neck threads using air blower. Then retighten
until reteaching sound is heard.
3.
CHECK FUEL FILLER CAP FUNCTION
Check for air releasing sound while opening the fuel filler cap.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
CHECK FUEL TANK VACUUM RELIEF VALVE
EC-322, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace fuel filler cap with a genuine one.
5.
CHECK FOR EVAP LEAK
.
Is there any leak in EVAP line?
YES
>> Repair or replace.
NO
>> GO TO 6.
6.
CHECK EVAP CANISTER VENT CONTROL VALVE
Check the following.
• EVAP canister vent control valve is installed properly.
• EVAP canister vent control valve.
EC-298, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace EVAP canister vent control valve and O-ring. Refer to
7.
CHECK IF EVAP CANISTER SATURATED WITH WATER
SEF915U
EC-320
< DTC/CIRCUIT DIAGNOSIS >
[HR16DE]
P0456 EVAP CONTROL SYSTEM
1. Remove EVAP canister (1) with EVAP canister vent control
valve (2) and EVAP control system pressure sensor attached.
2. Check if water will drain from the EVAP canister.
Does water drain from EVAP canister?
YES
>> GO TO 8.
NO-1 >> With CONSULT: GO TO 10.
NO-2 >> Without CONSULT: GO TO 11.
8.
CHECK EVAP CANISTER
Weigh the EVAP canister assembly with the EVAP canister vent control valve and EVAP control system pres-
sure sensor attached. Refer to
FL-12, "Removal and Installation"
.
The weight should be less than 1.6 kg (3.5 lb).
Is the inspection result normal?
YES-1 >> With CONSULT: GO TO 10.
YES-2 >> Without CONSULT: GO TO 11.
NO
>> GO TO 9.
9.
DETECT MALFUNCTIONING PART
Check the following.
• EVAP canister for damage
• EVAP hose between EVAP canister and vehicle frame for clogging or poor connection
>> Repair hose or replace EVAP canister. Refer to
FL-12, "Removal and Installation"
.
10.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE OPERATION
With CONSULT
1. Disconnect vacuum hose to EVAP canister purge volume control solenoid valve at EVAP service port.
2. Start engine and let it idle.
3. Select “PURG VOL CONT/V” in “ACTIVE TEST” mode of “ENGINE” using CONSULT.
4. Touch “Qu” on CONSULT screen to increase “PURG VOL CONT/V” opening to 100%.
5. Check vacuum hose for vacuum.
Is the inspection result normal?
YES
>> GO TO 13.
NO
>> GO TO 12.
11.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE OPERATION
Without CONSULT
1. Start engine and warm it up to normal operating temperature.
2. Stop engine.
3. Disconnect vacuum hose to EVAP canister purge volume control solenoid valve at EVAP service port.
4. Start engine and let it idle for at least 80 seconds.
5. Check vacuum hose for vacuum when revving engine up to 2,000 rpm.
Is the inspection result normal?
YES
>> GO TO 13.
NO
>> GO TO 12.
12.
CHECK VACUUM HOSE
Check vacuum hoses for clogging or disconnection. Refer to
.
Is the inspection result normal?
PBIB2731E
Vacuum should exist.
Vacuum should exist.
P0456 EVAP CONTROL SYSTEM
EC-321
< DTC/CIRCUIT DIAGNOSIS >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
YES
>> GO TO 13.
NO
>> Repair or reconnect the hose.
13.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
Check the EVAP canister purge volume control solenoid valve. Refer to
EC-292, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 14.
NO
>> Replace EVAP canister purge volume control solenoid valve. Refer to
14.
CHECK FUEL TANK TEMPERATURE SENSOR
Check the fuel tank temperature sensor. Refer to
EC-252, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 15.
NO
>> Replace fuel level sensor unit. Refer to
FL-5, "Removal and Installation"
.
15.
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
Check the EVAP control system pressure sensor. Refer to
FL-16, "Removal and Installation"
.
Is the inspection result normal?
YES
>> GO TO 16.
NO
>> Replace EVAP control system pressure sensor. Refer to
FL-16, "Removal and Installation"
.
16.
CHECK EVAP PURGE LINE
Check EVAP purge line (pipe, rubber tube, fuel tank and EVAP canister) for cracks or improper connection.
EC-41, "EVAPORATIVE EMISSION SYSTEM : System Description"
Is the inspection result normal?
YES
>> GO TO 17.
NO
>> Repair or reconnect the hose.
17.
CLEAN EVAP PURGE LINE
Clean EVAP purge line (pipe and rubber tube) using air blower.
>> GO TO 18.
18.
CHECK EVAP/ORVR LINE
Check EVAP/ORVR line between EVAP canister and fuel tank for clogging, kink, looseness and improper con-
nection. For location, refer to
EC-29, "On Board Refueling Vapor Recovery (ORVR)"
.
Is the inspection result normal?
YES
>> GO TO 19.
NO
>> Repair or replace hoses and tubes.
19.
CHECK RECIRCULATION LINE
Check recirculation line between fuel filler tube and fuel tank for clogging, kink, cracks, looseness and
improper connection.
Is the inspection result normal?
YES
>> GO TO 20.
NO
>> Repair or replace hose, tube or fuel filler tube.
20.
CHECK REFUELING EVAP VAPOR CUT VALVE
Check the refueling EVAP vapor cut valve. Refer to
EC-445, "Component Inspection (Refueling EVAP vapor
Is the inspection result normal?
YES
>> GO TO 21.
NO
>> Replace refueling EVAP vapor cut valve with fuel tank. Refer to
FL-5, "Removal and Installation"
21.
CHECK FUEL LEVEL SENSOR
EC-322
< DTC/CIRCUIT DIAGNOSIS >
[HR16DE]
P0456 EVAP CONTROL SYSTEM
Check the fuel level sensor. Refer to
MWI-47, "Component Inspection"
(TYPE A) or
(TYPE B). Check the vehicle type to confirm the service information in MWI section. Refer to
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> Replace fuel level sensor unit. Refer to
FL-5, "Removal and Installation"
.
Component Inspection
INFOID:0000000009267199
1.
CHECK FUEL FILLER CAP
1. Turn ignition switch OFF.
2. Remove fuel filler cap.
3. Wipe clean valve housing.
4. Install fuel filler cap adapter (commercial service tool) to fuel
filler cap.
5. Check valve opening pressure and vacuum.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
REPLACE FUEL FILLER CAP
Replace fuel filler cap.
CAUTION:
Use only a genuine fuel filler cap as a replacement. If an incorrect fuel filler cap is used, the MIL may
illuminate.
>> INSPECTION END
SEF445Y
Pressure:
15.3 - 20.0 kPa (0.156 - 0.204 kg/cm
2
, 2.22
- 2.90 psi)
Vacuum:
−6.0 to −3.3 kPa (−0.061 to −0.034 kg/cm
2
,
−0.87 to −0.48 psi)
SEF943S
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст