Nissan Versa Sedan. Manual — part 448
SERVICE DATA AND SPECIFICATIONS (SDS)
FL-19
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Fuel Tank
INFOID:0000000009267717
STANDARD AND LIMIT
Fuel tank capacity
Approx. 41.0 (10-7/8 US gal, 9 Imp gal)
Fuel recommendation
Refer to
GI-33, "Fuel (Regular Unleaded Gasoline Recommended)
.
FSU-1
SUSPENSION
C
D
F
G
H
I
J
K
L
M
SECTION
FSU
A
B
FSU
N
O
P
CONTENTS
FRONT SUSPENSION
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Suspension . . . . . . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tools . . . . . . . . . . . ....
Commercial Service Tools . . . . . . . . . ....
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
FRONT SUSPENSION ASSEMBLY . . . . ...
Inspection and Adjustment . . . . . . . . . ....
REMOVAL AND INSTALLATION . . . .
FRONT COIL SPRING AND STRUT . . . . .
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Disassembly and Assembly . . . . . . . . . ..
Disposal . . . . . . . . . . . . . . . . ...
TRANSVERSE LINK . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
FRONT STABILIZER . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
FRONT SUSPENSION MEMBER . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Wheel Alignment . . . . . . . . . . . . . .
Ball Joint . . . . . . . . . . . . . . . . ..
FSU-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009267394
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precautions for Suspension
INFOID:0000000009267395
• When installing rubber bushings, the final tightening must be carried out under unladen conditions with tires
on ground. Oil might shorten the life of rubber bushings. Be sure to wipe off any spilled oil.
- Unladen conditions mean that fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and
mats are in designated positions.
• After servicing suspension parts, be sure to check wheel alignment.
• Self-lock nuts are not reusable. Always use new ones when installing.
PREPARATION
FSU-3
< PREPARATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000009267396
The actual shapes of Kent-Moore tools may differ from those of special tools illustrated here.
Commercial Service Tools
INFOID:0000000009267397
Tool number
(Kent-Moore No.)
Tool name
Description
KV991040S1
(
—
)
1. KV99104020 Adapter A
2. KV99104030 Adapter B
3. KV99104040 Adapter C
4. KV99104050 Adapter D
5. KV99104060 Plate
6. KV99104070 Guide bolt
7. KV99104080 Spring
8. KV99104090 Center plate
Measuring wheel alignment
ST35652000
(
—
)
Strut attachment
Disassembling and assembling strut
KV10106700
(
—
)
Drift
Disassembling and assembling strut
mounting bearing
a: 25 mm (0.98 in) dia.
b: 18.5 mm (0.728 in) dia.
—
(J-49286)
Drift and pull gauge
Measuring drift and pull
ZZA1167D
ZZA0807D
ZZA0534D
AWEIA0156ZZ
Tool name
Description
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст