Nissan Versa Sedan. Manual — part 195
DLK-98
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
REMOTE KEYLESS ENTRY RECEIVER
Is the inspection result normal?
YES
>> Reconnect BCM, GO TO 4
NO
>> Repair or replace harness between BCM and remote keyless entry receiver.
4.
CHECK REMOTE KEYLESS ENTRY RECEIVER GROUND CIRCUIT
Check continuity between remote keyless entry receiver connector and ground.
Is the inspection result normal?
YES
>> GO TO 6
NO
>> GO TO 5
5.
CHECK REMOTE KEYLESS ENTRY RECEIVER CIRCUIT 2
Check continuity between BCM connector and remote keyless entry receiver connector.
Is the inspection result normal?
YES
>> GO TO 6
NO
>> Repair or replace harness between BCM and remote keyless entry receiver.
6.
CHECK REMOTE KEYLESS ENTRY RECEIVER CIRCUIT 3
1. Check continuity between BCM connector and remote keyless entry receiver connector.
2. Check continuity between BCM connector and ground.
Is the inspection result normal?
YES
>> GO TO 7
NO
>> Repair or replace harness between BCM and remote keyless entry.
7.
CHECK REMOTE KEYLESS ENTRY RECEIVER RSSI SIGNAL CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and remote keyless entry receiver harness connector.
3. Check continuity between BCM harness connector and ground.
BCM connector
Terminal
Ground
Continuity
M97
19
No
Remote keyless entry
receiver
connector
Terminal
Ground
Continuity
M90
1
Yes
BCM
connector
Terminal
Remote keyless entry
receiver
connector
Terminal
Continuity
M97
18
M90
1
Yes
BCM
connector
Terminal
Remote keyless entry
receiver
connector
Terminal
Continuity
M97
20
M90
2
Yes
BCM connector
Terminal
Ground
Continuity
M97
20
No
BCM
Remote keyless entry receiver
Continuity
Connector
Terminal
Connector
Terminal
M97
22
M90
3
Yes
REMOTE KEYLESS ENTRY RECEIVER
DLK-99
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> GO TO 8
NO
>> Repair or replace harness between BCM and remote keyless entry.
8.
CHECK REMOTE KEYLESS ENTRY RECEIVER RSSI SIGNAL
1. Reconnect remote keyless entry receiver connector.
2. Check signal between remote keyless entry receiver harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Replace remote keyless entry receiver. Refer to
DLK-188, "Removal and Installation"
9.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
.
>> Inspection End.
BCM
Ground
Continuity
Connector
Terminal
M97
22
No
(+)
(–)
Condition
Signal
(Reference value)
Remote keyless entry receiver
Connector
Terminal
M90
3
Ground
During waiting
When pressing
and holding either
button on Intelli-
gent Key
JMKIA5952GB
JMKIA5953GB
DLK-100
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
SHIFT P WARNING LAMP
SHIFT P WARNING LAMP
Component Function Check
INFOID:0000000009268782
1.
CHECK FUNCTION
1. Select INTELLIGENT KEY of BCM using CONSULT.
2. Select LCD in ACTIVE TEST mode.
3. Touch SET P to check that it works normally.
Is the inspection result normal?
YES
>> Shift P warning lamp is OK.
NO
>> Refer to
DLK-100, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000009268783
1.
CHECK SHIFT P WARNING LAMP
TM-418, "Component Parts Function Inspection"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
>> Inspection End.
TRUNK LID OPENER ACTUATOR
DLK-101
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
TRUNK LID OPENER ACTUATOR
Component Function Check
INFOID:0000000009268784
1.
CHECK FUNCTION
1. Select INTELLIGENT KEY of BCM using CONSULT.
2. Select TRUNK/GLASS HATCH in ACTIVE TEST mode.
3. Touch OPEN to check that it works normally.
Is the inspection result normal?
YES
>> Trunk lid opener actuator is OK.
NO
>> Refer to
DLK-101, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000009268785
Regarding Wiring Diagram information, refer to
DLK-59, "TRUNK LID OPENER SYSTEM : Wiring Diagram"
1.
CHECK TRUNK LID OPENER INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect trunk lid lock assembly connector.
3. Check voltage between trunk lid lock assembly harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK TRUNK LID OPENER ACTUATOR CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and trunk lid lock assembly harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-69, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK TRUNK LID OPENER ACTUATOR GROUND CIRCUIT
Check continuity between trunk lid lock assembly harness connector and ground.
Is the inspection normal?
(+)
(–)
Condition
Voltage
(Approx.)
Trunk lid lock assembly
Connector
Terminal
B51
3
Ground
Trunk lid opener switch is ON
12 V
BCM
Trunk lid lock assembly
Continuity
Connector
Terminal
Connector
Terminal
M99
53
B51
3
Yes
BCM
Ground
Continuity
Connector
Terminal
M99
53
No
Trunk lid lock assembly
Ground
Continuity
Connector
Terminal
B51
2
Yes
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст