Nissan Versa Sedan. Manual — part 242
DLK-286
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT DOOR
2. Loosen door hinge nuts on door side.
3. Adjust the surface height of front door according to the specifications provided.
4. Temporarily tighten door hinge nuts on door side.
5. Loosen door hinge bolts on body side.
6. Raise or lower the front door at rear end to adjust clearance of the front door according to the specifica-
tions provided.
7. After adjustment tighten bolts and nuts to the specified torque.
CAUTION:
• Check door hinge rotating point for poor lubrication. If necessary, apply body a suitable multi-
purpose grease.
• After adjusting, apply touch-up paint (body color) onto the heads of hinge bolts and nuts.
8. Install front fender. Refer to refer to
DLK-281, "FRONT FENDER : Removal and Installation"
.
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Removal and Installation
INFOID:0000000009268989
REMOVAL
Remove striker bolts and remove front door striker.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, check front door open/close, lock/unlock operation.
• After installation, perform the front door adjustment procedure. Refer to
DOOR HINGE
DOOR HINGE : Removal and Installation
INFOID:0000000009268990
REMOVAL
CAUTION:
• Use two people when removing or installing front door due to its heavy weight
• When removing and installing front door assembly, support the door using a suitable tool.
• Use shops cloths to protect surrounding components from damage during removal and installation
of front door assembly.
1. Remove front fender. Refer to
DLK-281, "FRONT FENDER : Removal and Installation"
2. Remove front door assembly. Refer to
DLK-283, "DOOR ASSEMBLY : Removal and Installation"
.
3. Remove front door hinge bolts (body side) and remove front door hinge.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the hinge mating surface.
• Perform the front door adjustment procedure. Refer to
DLK-285, "DOOR ASSEMBLY : Adjustment"
.
• After adjusting, apply touch-up paint (the body color) to the head of door hinge nuts.
FRONT DOOR
DLK-287
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• Check door hinge rotating point for poor lubrication. If neces-
sary, apply a suitable multi-purpose grease.
DOOR CHECK LINK
DOOR CHECK LINK : Removal and Installation
INFOID:0000000009268991
REMOVAL
1. Fully close the front door window.
2. Remove front door finisher. Refer to
INT-15, "Removal and Installation"
3. Remove front door speaker bolts.
4. Disconnect harness connector from front door speaker and remove.
5. Remove door check link bolt from body.
6. Remove door check link bolts on door panel.
7. Remove door check link (1) through the hole in door panel (2).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, check rear door open/close operation.
• Check door check link rotating point for poor lubrication. If
necessary, apply a suitable multi-purpose grease.
JMKIA8072ZZ
JMKIA8073ZZ
JMKIA8074ZZ
DLK-288
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
REAR DOOR
REAR DOOR
Exploded View
INFOID:0000000009268992
DOOR ASSEMBLY
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000009268993
CAUTION:
• Use two people when removing or installing rear door due to its heavy weight.
• When removing and installing rear door assembly, support door using a suitable tool.
• Use shop cloths to protect surrounding components from damage during removal and installation of
front door assembly.
REMOVAL
1. Remove rear door harness grommet (1) from body side outer
(2), and then pull out rear door harness.
1.
Rear door panel
2.
Grommet
3.
Striker bolt
4.
Door striker
5.
Bumper rubber
6.
Sealing screen (lower) (without door
speaker)
7.
Door check link
8.
Door hinge (lower)
9.
Door hinge (upper)
AWKIA1920GB
JMKIA8083ZZ
REAR DOOR
DLK-289
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2. Disconnect the harness connector (A) from rear door harness.
3. Remove door check link bolts from body.
4. Remove door hinge nuts (door side) and rear door assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the hinge mating surface.
• After installation, check rear door open/close, lock/unlock operation.
• Check door hinge rotating point for poor lubrication. If necessary, apply a suitable multi-purpose
grease.
• After installation, perform the rear door adjustment procedure. Refer to
.
• After adjusting, apply touch-up paint (body color) onto the head of door hinge nuts.
JMKIA8084ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст