Nissan Versa Sedan. Manual — part 220
DLK-198
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
SYSTEM
SYSTEM
AUTOMATIC DOOR LOCK/UNLOCK FUNCTION
AUTOMATIC DOOR LOCK/UNLOCK FUNCTION : System Diagram
INFOID:0000000009268906
AUTOMATIC DOOR LOCK/UNLOCK FUNCTION : System Description
INFOID:0000000009268907
DOOR LOCK FUNCTION
• The door lock and unlock switch (driver side) is built into power window main switch.
• The door lock and unlock switch (passenger side) is on door trim.
• Interlocked with the locking operation of door lock and unlock switch, door lock actuators of all doors are
locked.
• Interlocked with the unlocking operation of door lock and unlock switch, door lock actuators of all doors are
unlocked.
Door Key Cylinder
• With the door key inserted in the door key cylinder on driver side, turning it to “LOCK”, will lock door lock
actuator of all doors.
• With the door key inserted in the door key cylinder on driver side, turning it to “UNLOCK” once unlocks the
driver side door lock actuator; turning it to “UNLOCK” again within 60 seconds after the first unlock operation
unlocks all of the other doors. - (SELECTIVE UNLOCK OPERATION)
Selective unlock operation mode can be changed using “DOOR LOCK-UNLOCK SET” mode in “WORK SUP-
PORT”. Refer to
BCS-82, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
.
AUTOMATIC DOOR LOCKS (LOCK OPERATION)
The automatic door locks function is the function that locks all doors linked with the vehicle speed or shift posi-
tion.
Vehicle Speed Sensing Auto Door Lock
*1
All doors are locked when the vehicle speed reaches 24 km/h (15 MPH) or more.
BCM outputs the lock signal to all door lock actuators when it detects that the ignition switch is turned ON, all
doors are closed and the vehicle speed received from the combination meter via CAN communication
becomes 24 km/h (15 MPH) or more.
ALKIA2288GB
Input
Single
Function
Actuator
Door lock/unlock switch
Door lock/unlock signal
Door lock function
• Each door lock actuator
Door key cylinder switch
Each door switch
Door open/close signal
Key reminder function
Combination meter.
Warning buzzer signal
Vehicle speed signal
Automatic door lock/unlock
function
SYSTEM
DLK-199
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
If a door is opened and closed at any time during one ignition cycle (OFF
→ ON), even after initial auto door
lock operation has taken place, the BCM will relock all doors when the vehicle speed reaches 24 km/h (15
MPH) or more again.
Setting change of Automatic Door Locks (LOCK) Function
The LOCK operation setting of the automatic door locks function can be changed.
With CONSULT
The ON/OFF switching of the automatic door locks (LOCK) function and the type selection of the automatic
door locks (LOCK) function can be performed at the WORK SUPPORT setting of CONSULT. Refer to
"DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
.
Without CONSULT
The automatic door locks (LOCK) function can be switched ON/OFF by performing the following operation.
1. Close all doors (door switch OFF)
2. Push the ignition switch to the ON position
3. Press and hold the door lock and unlock switch for 5 seconds or more in the lock direction within 20 sec-
onds after turning the ignition switch ON.
4. The switching is completed when the hazard lamp blinks.
5. The ignition switch must be turned OFF and ON again between each setting change.
AUTOMATIC DOOR LOCKS (UNLOCK OPERATION)
The automatic door locks (UNLOCK) function is the function that unlocks all doors linked with the key position
or shift position.
IGN OFF Interlock Door Unlock
*1
All doors are unlocked when the power supply position is changed from ON to OFF.
BCM outputs the unlock signal to all door lock actuators when it detects that the power supply position is
changed from ignition switch ON to OFF.
Setting change of Automatic Door Locks (UNLOCK) Function
The UNLOCK operation setting of the automatic door locks function can be changed.
With CONSULT
The ON/OFF switching of the automatic door locks (UNLOCK) function and the type selection of the automatic
door locks (UNLOCK) function can be performed at the WORK SUPPORT setting of CONSULT. Refer to
82, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
.
Without CONSULT
The automatic door locks (UNLOCK) function can be switched ON/OFF by performing the following operation.
1. Close all doors (door switch OFF)
2. Place the ignition switch in the ON position
3. Press and hold the door lock and unlock switch for 5 seconds or more in the unlock direction within 20
seconds after turning the power supply position ON.
4. The switching is completed when the hazard lamp blinks.
5. The ignition switch must be turned OFF and ON again between each setting change.
*1
: This function is set to ON before delivery.
POWER DOOR LOCK SYSTEM
OFF
→ ON
: 2 blinks
ON
→ OFF
: 1 blink
OFF
→ ON
: 2 blinks
ON
→ OFF
: 1 blink
DLK-200
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
SYSTEM
POWER DOOR LOCK SYSTEM : System Diagram
INFOID:0000000009268908
POWER DOOR LOCK SYSTEM : System Description
INFOID:0000000009268909
DOOR LOCK FUNCTION
Functions Available by Operating the Door Lock and Unlock Switches on Driver Door and Passenger Door
• Interlocked with the locking operation of door lock and unlock switch, door lock actuators of all door lock
actuators are locked.
• Interlocked with the unlocking operation of door lock and unlock switch, door lock actuators of all door lock
actuators are unlocked.
Functions Available by Operating the Key Cylinder Switch on Driver Door
• Interlocked with the locking operation of door key cylinder, door lock actuators of all door lock actuators are
locked.
Selective Unlock Operation
• When door key cylinder is unlocked, door lock actuator driver side is unlocked.
• When door key cylinder is unlocked for the second time within 5 seconds after the first operation, door lock
actuators on all doors are unlocked.
Select unlock operation mode can be changed using DOOR LOCK-UNLOCK SET mode in “WORK SUP-
PORT”. Refer to
BCS-82, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
.
REMOTE KEYLESS ENTRY SYSTEM
ALKIA2289GB
Switch
Input/output signal to BCM
BCM function
Actuator
Main power window and door
lock/unlock switch
Door lock/unlock signal
Door lock/unlock control
Door lock actuator
Power window and door lock/
unlock switch RH
Front door lock key cylinder
switch LH
SYSTEM
DLK-201
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOTE KEYLESS ENTRY SYSTEM : System Diagram
INFOID:0000000009268910
REMOTE KEYLESS ENTRY SYSTEM : System Description
INFOID:0000000009268911
The remote keyless entry system can be locked and unlocked by pressing door lock and unlock button of key-
fob.
DOOR LOCK AND UNLOCK OPERATION
• When door lock and unlock button of keyfob is pressed, door lock and unlock signal transmits from keyfob to
BCM via remote keyless entry receiver.
• When BCM receives the door lock and unlock signal, it operates door lock actuator, flashes the hazard lamp
(lock: 2 times, unlock: 1 time) and horn chirp signal to IPDM E/R at the same time as a reminder.
• IPDM E/R honks horn (lock: 1 time) as a reminder.
OPERATION CONDITION
OPERATION AREA
To ensure that the keyfob works effectively, use within 10 m (33ft) range of the vehicle, however the operable
range may differ according to surroundings.
SELECTIVE UNLOCK OPERATION
When door lock is unlocked, pressing LOCK button on keyfob once will lock all doors. When door lock is
locked, pressing UNLOCK button on keyfob will unlock driver side door. Pressing UNLOCK button on keyfob
second time within 5 seconds from the first time will unlock all doors.
HAZARD AND HORN REMINDER
When the doors are locked or unlocked by keyfob, power is supplied to sound horn and flash hazard warning
lamps as a reminder
The hazard and horn reminder has C mode (horn chirp mode) and S mode (non-horn chirp mode).
How to Change Hazard and Horn Reminder Modes
With CONSULT
Hazard and horn reminders can be changed using "WORK SUPPORT" mode in "MULTI REMOTE ENT".
ALKIA2290GB
Remote controller operation
Operation condition
Lock/unlock
Key switch is OFF. Mechanical key is removed from the ignition cylinder.
Hazard reminder setting
Mode 1
Mode 2
Mode 3
Mode 4
Keyfob operation
Lock
Unlock
Lock
Unlock
Lock
Unlock
Lock
Unlock
Hazard warning lamp blink
—
—
—
Once
Twice
—
Twice
Once
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст