Nissan Versa Sedan. Manual — part 673
SE-18
< REMOVAL AND INSTALLATION >
FRONT SEAT
PASSENGER SIDE : Exploded View
INFOID:0000000009268520
WITH REMOVABLE HEADREST
ALJIA1000ZZ
1.
Seatback trim
2.
Seatback pad
3.
Headrest
4.
Headrest holder (free)
5.
Headrest holder (locked)
6.
Chute rod
7.
Seat frame assembly
8.
Side air bag module
9.
Recline lever
FRONT SEAT
SE-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
WITHOUT REMOVABLE HEADREST
10. Seat cushion outer finisher (RH)
11. Seat cushion trim
12. Seat cushion pad
13. Seat belt buckle
14. Seat cushion outer finisher (LH)
ALJIA0999ZZ
1.
Seatback trim
2.
Seatback pad
3.
Chute rod
4.
Side air bag module
5.
Recline lever
6.
Seat cushion outer finisher (RH)
SE-20
< REMOVAL AND INSTALLATION >
FRONT SEAT
PASSENGER SIDE : Removal and Installation
INFOID:0000000009268521
REMOVAL
WARNING:
Do not leave any objects (screwdrivers, tools, etc.) on the seat during seat repair. It can lead to per-
sonal injury if the side air bag module should accidentally deploy.
CAUTION:
• When removing or installing the seat trim, handle it carefully to keep dirt out and to avoid damage.
• When checking the power seat circuit for continuity using a circuit tester, do not confuse its connec-
tor with the side air bag module connector. Such an error may cause the air bag module to deploy.
• Do not drop, tilt, or bump the side air bag module while installing the seat. Always handle it with
care.
• After the front side air bag module inflates, the front seatback assembly must be replaced.
• When removing and installing the seat, use shop cloths to protect components from damage.
• Before removing the front seat, turn the ignition switch OFF, disconnect both battery cables and wait
at least three minutes.
1. Disconnect the negative and positive battery terminals and wait at least three minutes. Refer to
2. Slide the seat to the full forward position.
3. Remove the two rear seat bolts.
4. Slide the seat to the full rearward position.
5. Remove the two front seat bolts.
6. Tilt the seat rearward to disconnect the harness connectors from the seat and remove.
INSTALLATION
Installation is in the reverse order of removal.
WARNING:
• Perform additional services when installing front passenger seat. Refer to
.
• Zero point reset must be performed every time the front passenger seat is removed from the vehicle.
• Zero point reset is done after the front passenger seat is installed in vehicle and all bolts are tight-
ened to specification.
CAUTION:
Make sure that the seat harness or the floor trim is not damaged during installation.
NOTE:
• When installing the RH front seat, tighten the bolts in the order
shown.
7.
Seat cushion trim
8.
Seat cushion pad
9.
Seat belt buckle
10. Seat cushion outer finisher (LH)
11. Seat frame assembly
RH front seat bolt torque
: 40 Nm (4.1 kg-m, 30 ft-lb)
AWJIA0921ZZ
REAR SEAT
SE-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
REAR SEAT
Exploded View - Fixed Seatback
INFOID:0000000009268522
FIXED SEATBACK
ALJIA0982ZZ
1.
Headrest holder (locked)
2.
Headrest holder (free)
3.
Rear seatback assembly
4.
Seatback trim
5.
Seatback pad
6.
LATCH bracket (RH)
7.
Seat cushion assembly
8.
Seat cushion trim
9.
Seat cushion pad
10. Seat cushion hook
11. LATCH bracket (LH)
12. Headrest
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст