Nissan Versa Sedan. Manual — part 452
FSU-16
< REMOVAL AND INSTALLATION >
FRONT SUSPENSION MEMBER
FRONT SUSPENSION MEMBER
Exploded View
INFOID:0000000009267408
Removal and Installation
INFOID:0000000009267409
REMOVAL
1. Remove the wheel and tire assemblies using power tool. Refer to
2. Remove transverse link. Refer to
FSU-12, "Removal and Installation"
3. Remove steering outer socket from steering knuckle. Refer to
ST-14, "Removal and Installation"
4. Separate intermediate shaft from the lower joint. Refer to
ST-9, "Removal and Installation"
.
5. Remove the engine rear torque rod.
6. Set suitable jack under front suspension member.
CAUTION:
Do not damage the front suspension member with jack.
7. Remove suspension member bolts.
8. Gradually lower the jack to remove front suspension member from vehicle body.
9. Remove steering gear assembly from suspension member. Refer to
ST-14, "Removal and Installation"
.
INSTALLATION
Installation is in the reverse order of removal.
• For installation of the suspension member, temporarily tighten the
bolts in the sequence shown and tighten them to the specified
torque.
• Refer to
for tightening torque.
• Tighten the wheel nuts to specification. Refer to
.
• After installation, perform final tightening of each part under
unladen conditions with tires on ground. Check wheel alignment.
FSU-6, "Inspection and Adjustment"
.
1.
Front suspension member
2.
Transverse link
AWEIA0210GB
: Front
AWEIA0211ZZ
SERVICE DATA AND SPECIFICATIONS (SDS)
FSU-17
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Alignment
INFOID:0000000009267410
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Ball Joint
INFOID:0000000009267411
Item
Standard
Camber
Degree minute (Decimal degree)
Minimum
−0° 50′ (−0.83°)
Nominal
−0° 05′ (−0.08°)
Maximum
0
° 40′ (0.66°)
Left and right differ-
ence
0
° 35′ (0.58°)
Caster
Degree minute (Decimal degree)
Minimum
2
° 55′ (2.92°)
Nominal
3
° 40′ (3.67°)
Maximum
4
° 25′ (4.41°)
Left and right differ-
ence
0
° 45′ (0.75°)
Kingpin inclination
Degree minute (Decimal degree)
Minimum
11
° 00′ (11.00°)
Nominal
11
° 45′ (11.75°)
Maximum
12
° 30′ (12.50°)
Total toe-in
Distance (A - B)
Minimum
Out 1 mm (0.03 in)
Nominal
In 1 mm (0.05 in)
Maximum
In 3 mm (0.11 in)
Angle
Degree minute second (Decimal
degree)
Minimum
Out 0
° 4′ 48″ (0.08°)
Nominal
In 0
° 4′ 48″ (0.08°)
Maximum
In 0
° 14′ 24″ (0.24°)
SFA234AC
Item
Standard
Swing torque
0.5 – 3.4 N·m (0.05 – 0.34 kg-m, 4.4 – 30 in-lb)
Measurement on spring balance
15.4 – 104.7 N (1.6 – 10.7 kg-f, 3.5 – 23.5 lb-f)
Axial end play
0 mm (0 in)
FSU-18
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheelarch Height
INFOID:0000000009267412
Unit: mm (in)
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Market
United States
Canada
Front (Hf)
683 (26.89)
684 (26.93)
Rear (Hr)
668 (26.30)
668 (26.30)
LEIA0085E
A
B
C
D
E
F
G
H
I
J
K
L
M
N
P
O
QUICK REFERENCE INDEX
A GENERAL INFORMATION
B ENGINE
C
D TRANSMISSION & DRIVE-
LINE
DLN
Driveline
E SUSPENSION
SCS
Suspension Control System
F BRAKES
G STEERING
H RESTRAINTS
SBC
Seat Belt Control System
I VENTILATION, HEATER &
AIR CONDITIONER
Heater & Air Conditioning System
Heater & Air Conditioning Control System
J BODY INTERIOR
ADP
Automatic Drive Positioner
K BODY EXTERIOR,
DOORS, ROOF & VEHICLE
SECURITY
RF
Roof
L DRIVER CONTROLS
M ELECTRICAL & POWER
CONTROL
Power Supply, Ground & Circuit Elements
N DRIVER INFORMATION &
MULTIMEDIA
Meter, Warning Lamp & Indicator
SN
Sonar System
Audio, Visual & Navigation System
O CRUISE CONTROL
P MAINTENANCE
All rights reserved. No part
of this Service Manual may
be reproduced or stored in a
retrieval system, or transmit-
ted in any form, or by any
means, electronic, mechani-
cal, photo-copying, record-
ing or otherwise, without the
prior written permission of
Nissan North America, Inc.
April 2013
Publication No. SM
14E1N17U0
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст