Nissan Versa Sedan. Manual — part 832
TM-234
< REMOVAL AND INSTALLATION >
[4AT: RE4F03C]
A/T SHIFT SELECTOR
• When connecting the control cable (1) to the shift selector assem-
bly (2), face the grooved surface of the rib (A) up and insert the
control cable until it stops.
Disassembly and Assembly
INFOID:0000000009268017
DISASSEMBLY
1. Slide the shift selector handle cover (1) down.
CAUTION:
Do not damage the shift selector handle cover.
2. Pull out the lock pin (2).
3. Pull the shift selector handle (3) and shift selector handle cover
upward to remove them.
4. Remove the position lamp.
5. Disengage the hooks (A) (4 locations), and lift up the position
indication panel (1) to separate it from the shift selector assem-
bly (2).
CAUTION:
Do not damage the shift selector assembly.
ASSEMBLY
Assembly is in the reverse order of disassembly.
• Follow the procedure below to install the shift selector handle.
1. Install the lock pin (2) onto the shift selector handle (3).
2. Install the shift selector handle cover (1) onto the shift selector
handle.
3. Press the shift selector handle onto the shift selector until it
clicks.
CAUTION:
• When pressing the shift selector handle onto the shift
selector, do not press the shift selector handle button.
• Do not strike the shift selector handle to install it into
place.
4. After installing shift selector handle, pull the handle to check that
it does not become disconnected.
JSDIA1624ZZ
JSDIA1796ZZ
ALDIA0264ZZ
JSDIA1796ZZ
A/T SHIFT SELECTOR
TM-235
< REMOVAL AND INSTALLATION >
[4AT: RE4F03C]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Inspection and Adjustment
INFOID:0000000009268018
INSPECTION
1. Move the shift selector to “P” position, and turn ignition switch ON.
2. Check that shift selector can be moved to other than “P” position when brake pedal is depressed. Also
check that shift selector can be moved from “P” position only when brake pedal is depressed.
3. Move the shift selector and check for excessive effort, sticking, noise or rattle.
4. Check that shift selector stops at each position with the feel of engagement when it is moved through all
the positions. Check that the actual position of shift selector matches the position shown by shift position
indicator and manual lever on the transaxle.
5. The method of operating shift selector to individual positions cor-
rectly should be as shown.
6. When shift selector handle button is pressed in “P”, “R”, “N”, “D”,
“2” or “1” position without applying forward/backward force to
shift selector, check button operation for sticking.
7. Check that back-up lamps illuminate only when shift selector is
placed in the “R” position.
8. Check that back-up lamps do not illuminate when shift selector
is pushed toward the “R” position when in the “P” or “N” position.
CAUTION:
Check the lighting without pressing shift selector handle
button.
9. Check that the engine can only be started with shift selector in the “P” and “N” positions.
10. Check that transaxle is locked completely when shift selector is in “P” position.
ADJUSTMENT
1. Move shift selector to “ P” position.
CAUTION:
Rotate the wheels at least a quarter turn and be certain the transaxle is locked in the "P" position.
2. Loosen the control cable nut (A).
3. Place manual lever (B) to “P” position.
CAUTION:
Do not apply force to the manual lever.
4. Tighten the control cable nut. Refer to
CAUTION:
Do not move the manual lever when tightening.
SCIA6984E
JSDIA1951ZZ
TM-236
< REMOVAL AND INSTALLATION >
[4AT: RE4F03C]
CONTROL CABLE
CONTROL CABLE
Exploded View
INFOID:0000000009268019
Removal and Installation
INFOID:0000000009268020
CAUTION:
Always apply the parking brake before performing removal and installation.
REMOVAL
1. Remove the battery. Refer to
PG-63, "Removal and Installation"
2. Remove the TCM and bracket. Refer to
TM-241, "Removal and Installation"
.
3. Remove the IPDM E/R. Refer to
PCS-56, "Removal and Installation"
.
4. Remove the center console. Refer to
IP-23, "Removal and Installation"
.
5. Remove the control cable from the shift selector assembly.
6. Disengage the pawls (B) of the grommet (A), and pull down-
wards to remove.
7. Remove the control cable nut from the manual lever.
1.
Bracket B
2.
Lock plate
3.
Transaxle assembly
4.
Bracket A
5.
Control cable
6.
Shift selector assembly
A: Manual lever
B: Grommet
JSDIA1921GB
JSDIA1809ZZ
CONTROL CABLE
TM-237
< REMOVAL AND INSTALLATION >
[4AT: RE4F03C]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
8. Remove the lock plate (1).
9. Lift up the heat plate.
10. Remove the control cable (1) from the bracket (2).
11. Remove the control cable from the vehicle.
12. Remove bracket.
INSTALLATION
Installation is in the reverse order of removal.
• From below the vehicle, press the grommet (A) into place until the
pawls (B) make a click sound.
CAUTION:
Check that pulling down on the grommet does not disconnect
it.
• Pay attention to the following when connecting the control cable to the shift selector.
1. When connecting the control cable (1) to the shift selector
assembly (2), face the grooved surface of the rib (A) up and
insert the control cable until it stops.
JSDIA1812ZZ
: Front
JPDIA0107ZZ
JSDIA1809ZZ
JSDIA1624ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст