Nissan Versa Sedan. Manual — part 432
EXT-14
< SYMPTOM DIAGNOSIS >
SQUEAK AND RATTLE TROUBLE DIAGNOSES
LAIA0071E
FRONT BUMPER
EXT-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
REMOVAL AND INSTALLATION
FRONT BUMPER
Exploded View
INFOID:0000000009268550
1.
Front bumper side bracket (RH)
2.
Front bumper reinforcement
3.
Front bumper energy absorber
4.
Front bumper fascia finisher (RH)
(If equipped)
5.
Front bumper fascia
6.
Fog lamp finisher (RH) (if
equipped)
7.
Tow cover
8.
License plate bracket
9.
Under cover
AWKIA2508ZZ
EXT-16
< REMOVAL AND INSTALLATION >
FRONT BUMPER
Removal and Installation
INFOID:0000000009268551
REMOVAL
CAUTION:
Bumper fascia is made of resin. Do not apply strong force to it, and be careful to prevent contact with
oil.
1. Open hood.
2. Remove front bumper fascia upper side clips (A).
3. Remove under cover. Refer to
EXT-19, "Removal and Installation"
4. Remove fender protector clips and screws to access bumper fascia screw. Refer to
5. Remove front bumper fascia screws (A) (LH/RH).
6. Remove front bumper fascia lower side clips and screws.
7. Pull front bumper fascia away as shown by the arrows in the
illustration and then disengage front bumper fascia from front
bumper side brackets (LH/RH).
: Pawl
CAUTION:
When removing front bumper fascia, two people are
required to avoid damaging.
8. Disconnect the harness connectors from the front fog lamps (LH/RH) (If equipped).
9. Remove front bumper fascia.
10. Remove the following parts after removing front bumper fascia.
• Front bumper side brackets (LH/RH)
• Fog lamp finishers (LH/RH) (If equipped)
10. Fog lamp finisher (LH) (if
equipped)
11.
Front bumper fascia finisher (LH)
(if equipped)
12. Front bumper side bracket (LH)
13. Front spoiler
A.
Spring nut
B.
Screw grommet
Pawl
JMKIA8016ZZ
JMKIA8017ZZ
AWKIA1890ZZ
FRONT BUMPER
EXT-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
• Fog lamps (LH/RH) (If equipped). Refer to
EXL-105, "Removal and Installation"
• Front grille. Refer to
EXT-23, "Removal and Installation"
• License plate bracket
11. Remove front bumper energy absorber.
12. Remove nuts and front bumper reinforcement.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
• The following table shows the specified values for checking normal installation specifications.
• Fitting adjustment cannot be performed.
JMKIA8019ZZ
Portion
Clearance
Surface height difference
Front bumper – Hood
A – A
2.5 – 6.3 mm
(0.10 – 0.25 in)
(
−1.45) – (+2.45) mm
[(
−0.057) – (+0.096) in]
Front bumper – Headlamp
B – B
0.1 – 4.2 mm
(0.004 – 0.17 in)
—
C – C
0.1 – 3.9 mm
(0.004 – 0.15 in)
0.1 – 3.9 mm
(0.004 – 0.15 in)
Front bumper – Front fender D – D
0.0 – 1.0 mm
(0.000 – 0.04 in)
(
−0.3) – (+1.7) mm
[(
−0.01) – (+0.07) in]
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст