Nissan Almera Tino V10 (2001 year). Manual — part 2
SFA800
Transaxle side (T83, T86C & GI2300I)
NLAX0019S05
1.
Install boot and new small boot band on drive shaft.
Cover drive shaft serration with tape so as not to damage boot
during installation.
SFA612
2.
Install spider assembly securely, making sure the marks which
were made during disassembly are properly aligned.
3.
Install new snap ring.
NAX005
4.
Pack drive shaft with specified amount of grease.
Specified amount of grease:
Refer to AX-19, SDS
5.
Install slide joint housing.
6.
Set boot so that it does not swell and deform when its lenght
is “L
2
”:
Refer to AX-19, SDS
SFA395
Make sure that the boot is properly installed on the drive shaft
groove.
7.
Lock new larger and smaller boot bands securely with a suit-
able tool.
SFA618
Support Bearing
NLAX0019S04
+
Press bearing into retainer.
FRONT AXLE
Drive Shaft (Cont’d)
AX-17
SFA694
+
Press drive shaft into bearing.
SFA444B
+
Install snap ring.
+
Install new dust shield.
FRONT AXLE
Drive Shaft (Cont’d)
AX-18
Service Data and Specifications (SDS)
DRIVE SHAFT
=NLAX0020
NLAX0020S02
QG
SR
YD
LH
RH
Joint type
Transaxle side
T83
GI2300I
D90
T86C
D90
Grease
Quality
39709-55E00
Joint type
Wheel side
B83
AC2300I
Z100
B90
Grease
Quality
Nissan genuine grease or equivalent
39209-01A00
Nissan genuine
grease or equiva-
lent
Grease
Capacity
g (oz)
Transaxle side
125 - 145
(4.41 - 5.11)
125.5 - 135.5
(4.42 - 4.77)
165 - 175
(5.82 - 6.17)
145 - 155
(5.11 - 5.47)
145 - 165
(5.11 - 5.82)
Wheel side
80 - 100
(2.82 - 3.53)
40 - 50
(1.41 - 1.76)
Cannot be disassembled *2
120 - 140
(4.41 - 4.94)
Boot length
mm (in)
Transaxle side “L
2
”
98 - 100
(3.86 - 3.94)*1
97 - 99 (3.82 - 3.90)*1
98 (3.86) *1
Wheel side “L
1
”
94 - 96
(3.70 - 3.78)*1
Cannot be disassembled *2
110 (4.33)
SFA961AA
SFA962A
*1: Fit boot to boot groove in bar shaft
*2: Z100 type joint assembly cannot be disassembled because a plastic boot and special boot band are used. Do not use other drive
shaft boots. If the boot or joint is damaged, replace the drive shaft assembly.
FRONT AXLE
Service Data and Specifications (SDS)
AX-19
DYNAMIC DAMPER (WHERE FITTED)
=NLAX0033
NLAX0033S01
Unit: mm (in)
QG
YD
SR
LH
RH
LH
RH
LH
RH
Distance
“A”
178 - 184
(7.01 - 7.24)
375 - 381
(14.76 - 15.00)
172 - 178
(6.77 - 7.01)
190 -196
(7.48 - 7.72)
205 -215
(8.07 - 8.46)
205 - 215
(8.07 - 8.46)
“B”
70 (2.76)
64 (2.52)
70 (2.76)
70 (2.76)
70 (2.76)
70 (2.76)
SAX015
WHEEL BEARING (FRONT)
NLAX0021
Wheel bearing axial end play limit
mm (in)
0.05 (0.0020)
Wheel bearing lock nut tightening torque
N·m (kg-m, ft-lb)
255 - 333 (26 - 34, 188 - 245)
FRONT AXLE
Service Data and Specifications (SDS) (Cont’d)
AX-20
SBR686C
Precautions
PRECAUTIONS
NLAX0022
+
When installing each rubber part, final tightening must be
carried out under unladen condition* with tires on ground.
*: Fuel, radiator coolant and engine oil full. Spare tire, jack,
hand tools and mats in designated positions.
+
Use flare nut wrench when removing or installing brake
tubes.
+
After installing removed suspension parts, check wheel
alignment.
+
Do not jack up at the trailing arm and lateral link.
+
Always torque brake lines when installing.
Preparation
SPECIAL SERVICE TOOLS
NLAX0032
Tool number
Tool name
Description
KV40104710
Drift
NT474
Install ABS sensor rotor
a: 76.3 mm (3.004 in) dia.
b: 67.9 mm (2.673 in) dia.
ST3072000
Drift
NT115
Install ABS sensor rotor
a: 77 mm (3.03 in) dia.
b: 55.5 mm (2.185 in) dia.
COMMERCIAL SERVICE TOOLS
NLAX0024
Tool name
Description
1 Flare nut crowfoot
2 Torque wrench
NT360
Removing and installing brake piping
a: 10 mm (0.39 in)
REAR AXLE
Precautions
AX-21
Noise, Vibration and Harshness (NVH)
Troubleshooting
NLAX0025
Refer to “Noise, Vibration and Harshness (NVH) Troubleshooting”,
“FRONT AXLE”, AX-3.
SMA525A
On-vehicle Service
REAR AXLE PARTS
NLAX0026
Check axle and suspension parts for excessive play, wear or dam-
age.
+
Shake each rear wheel to check for excessive play.
SRA690A
REAR WHEEL BEARING
NLAX0027
+
Check axial end play.
Axial end play:
0.05 mm (0.0020 in)
+
Check that wheel hub bearings operate smoothly.
+
Check tightening torque of wheel bearing lock nut.
: 187 - 254 N·m (19 - 26 kg-m, 138 - 188 ft-lb)
+
Replace wheel bearing assembly if there is axial end play or
wheel bearing does not turn smoothly. Refer to “Wheel Hub”,
“REAR AXLE”, AX-23.
REAR AXLE
Noise, Vibration and Harshness (NVH) Troubleshooting
AX-22
Wheel Hub
COMPONENTS
NLAX0028
NAX001
1.
Spindle
2.
Baffle plate
3.
ABS sensor rotor
4.
Wheel hub bearing
5.
Wheel bearing lock nut
6.
Hub cap
7.
ABS sensor
REMOVAL
NLAX0029
CAUTION:
+
Before removing the rear wheel hub assembly, disconnect
the ABS wheel sensor from the assembly. Then move it
away from the hub assembly. Failure to do so may result
in damage to the sensor wires and the sensor becoming
inoperative.
+
Wheel hub bearing does not require maintenance. If any of
the following symptoms are noted, replace wheel hub
bearing assembly.
1)
Growling noise is emitted from wheel hub bearing dur-
ing operation.
2)
Wheel hub bearing drags or turns roughly. This occurs
when turning hub by hand after bearing lock nut is tight-
ened to specified torque.
REAR AXLE
Wheel Hub
AX-23
SRA711A
1.
Remove brake caliper assembly.
2.
Remove wheel bearing lock nut.
3.
Remove brake rotor (models with disk brake) or brake drum
(models with drum brakes).
4.
Remove wheel hub bearing from spindle.
CAUTION:
Do not disconnect brake hose from caliper.
+
Suspend caliper assembly with wire so as not to stretch
brake hose.
+
Be careful not to depress brake pedal, or piston will pop
out.
Make sure brake hose is not twisted.
ARA082
5.
Remove the sensor rotor using suitable puller, drift and bea
ring replacer.
SAX014
INSTALLATION
NLAX0030
+
With vehicles equipped with ABS, press-fit ABS sensor rotor
into wheel hub bearing using a drift.
Do not reuse ABS sensor rotor. When installing, replace it
with a new one.
SRA734AB
+
Press-fit ABS sensor rotor as far as the location shown in fig-
ure at left.
Height “h”:
12.5 - 13.5 mm (0.492 - 0.531 in)
REAR AXLE
Wheel Hub (Cont’d)
AX-24
SRA712A
+
Install wheel hub bearing.
+
Tighten wheel bearing lock nut.
Before tightening, apply oil to threaded portion of rear spindle.
Do not reuse wheel bearing lock nut.
: 187 - 254 N·m (19 - 26 kg-m, 138 - 188 ft-lb)
+
Check that wheel bearings operate smoothly.
SRA737A
+
Check wheel hub bearing axial end play.
Axial end play:
0.05 mm (0.0020 in)
SFA599B
+
Clinch two places of lock nut.
SRA738A
+
Install hub cap using a suitable tool.
Do not reuse hub cap. When installing, replace it with a
new one.
REAR AXLE
Wheel Hub (Cont’d)
AX-25
Service Data and Specifications (SDS)
WHEEL BEARING (REAR)
=NLAX0031
Wheel bearing axial end play
mm (in)
0.05 (0.0020)
Wheel bearing lock nut tightening torque
N·m (kg-m, ft-lb)
187 - 254 (19 - 26, 138 - 188)
REAR AXLE
Service Data and Specifications (SDS)
AX-26
AUTOMATIC TRANSAXLE
CONTENTS
EURO-OBD
. . . . . . . . . 4
Alphabetical & P No. Index for DTC . . . . . . ...4
. . . . . . . . . . . . . . . ...6
Precautions for Supplemental Restraint System
(SRS)
. . . . . . . . . . . . . ..6
Precautions for On Board Diagnostic (EURO-
OBD) System of CVT and Engine. . . . . . . ...6
Precautions . . . . . . . . . . . . . . . . ..6
Service Notice or Precautions . . . . . . . . . .7
Wiring Diagrams and Trouble Diagnoses. . . . . 8
. . . . . . . . . . . . . . . ...9
Special Service Tools . . . . . . . . . . . . ..9
. . . . . . . . . . . . . . . . . .10
Checking CVT Fluid. . . . . . . . . . . . ...10
Changing CVT Fluid . . . . . . . . . . . . .. 11
. . . . . . . . . . . . . ..12
CVT Electrical Parts Location. . . . . . . . . 12
Circuit Diagram . . . . . . . . . . . . . . ..13
Cross-sectional View - RE0F06A . . . . . . . ..14
Control System . . . . . . . . . . . . . . ..15
EURO-OBD
ON BOARD DIAGNOSTIC SYSTEM
DESCRIPTION
. . . . . . . . . . . . . . . ...18
Introduction . . . . . . . . . . . . . . . . 18
EURO-OBD Function for CVT System. . . . . ..18
EURO-OBD Diagnostic Trouble Code (DTC). . . 18
Malfunction Indicator (MI) . . . . . . . . . . ..21
CONSULT-II . . . . . . . . . . . . . . . ...21
EXCEPT FOR EURO-OBD
ON BOARD DIAGNOSTIC SYSTEM
DESCRIPTION
. . . . . . . . . . . . . . . ...31
CONSULT-II . . . . . . . . . . . . . . . ...31
Diagnostic Procedure Without CONSULT-II. . . ..35
EURO-OBD
TROUBLE DIAGNOSIS - INTRODUCTION
. . . . ..41
Introduction . . . . . . . . . . . . . . . . 41
Work Flow. . . . . . . . . . . . . . . . ..44
EXCEPT FOR EURO-OBD
TROUBLE DIAGNOSIS - INTRODUCTION
. . . . ..46
Introduction . . . . . . . . . . . . . . . . 46
Work Flow. . . . . . . . . . . . . . . . ..49
TROUBLE DIAGNOSIS - BASIC INSPECTION
. . ...51
CVT Fluid Check . . . . . . . . . . . . . ...51
Stall Test . . . . . . . . . . . . . . . . . 51
Line Pressure Test. . . . . . . . . . . . . .52
Road Test. . . . . . . . . . . . . . . . ...53
TROUBLE DIAGNOSIS - GENERAL
DESCRIPTION
. . . . . . . . . . . . . . . ...58
TCM Terminals and Reference Value. . . . . . 58
TROUBLE DIAGNOSIS FOR POWER SUPPLY
. . ..62
Wiring Diagram - AT - MAIN. . . . . . . . . ..62
TCM Terminals and Reference Value. . . . . . 64
Diagnostic Procedure . . . . . . . . . . . . 65
EURO-OBD
DTC P0705 PARK/NEUTRAL POSITION (PNP)
SWITCH
. . . . . . . . . . . . . . . . . . .66
Description . . . . . . . . . . . . . . . . .66
Wiring Diagram - AT - PNP/SW. . . . . . . . .68
Diagnostic Procedure . . . . . . . . . . . . 70
Component Inspection. . . . . . . . . . . ...72
DTC P0710 CVT FLUID TEMPERATURE SENSOR
CIRCUIT
. . . . . . . . . . . . . . . . . . .73
Description . . . . . . . . . . . . . . . . .73
Wiring Diagram - AT - FTS . . . . . . . . . . 75
Diagnostic Procedure . . . . . . . . . . . . 77
DTC P0715 PRIMARY SPEED SENSOR
. . . . . .79
Description . . . . . . . . . . . . . . . . .79
Wiring Diagram - AT - PSSA/T . . . . . . . . ..80
Diagnostic Procedure . . . . . . . . . . . . 82
Component Inspection. . . . . . . . . . . ...83
DTC P0720 VEHICLE SPEED SENSOR
(SECONDARY SPEED SENSOR)
. . . . . . . . 84
Description . . . . . . . . . . . . . . . . .84
Wiring Diagram - AT - VSSA/T . . . . . . . . ..86
Diagnostic Procedure . . . . . . . . . . . . 88
Component Inspection. . . . . . . . . . . ...89
. . . . . . .90
Description . . . . . . . . . . . . . . . . .90
Wiring Diagram - AT - ENGSS . . . . . . . . ..91
Diagnostic Procedure . . . . . . . . . . . . 92
DTC P0740 TORQUE CONVERTER CLUTCH
SOLENOID VALVE
. . . . . . . . . . . . . . 94
Description . . . . . . . . . . . . . . . . .94
Wiring Diagram - AT - TCV. . . . . . . . . . 96
Diagnostic Procedure . . . . . . . . . . . . 97
Component Inspection. . . . . . . . . . . ...98
DTC P0745 LINE PRESSURE SOLENOID VALVE
. .99
Description . . . . . . . . . . . . . . . . .99
Wiring Diagram - AT - LPSV. . . . . . . . . 101
Diagnostic Procedure . . . . . . . . . . . ..102
Component Inspection. . . . . . . . . . . .103
DTC P1705 THROTTLE POSITION SENSOR
. . ...104
Description . . . . . . . . . . . . . . . ...104
Wiring Diagram - AT - TPS. . . . . . . . . ..106
Diagnostic Procedure . . . . . . . . . . . ..108
Component Inspection. . . . . . . . . . . . 111
DTC P1777 STEP MOTOR - CIRCUIT
. . . . . ... 112
Description . . . . . . . . . . . . . . . ... 112
Wiring Diagram - AT - STM . . . . . . . . . . 114
Diagnostic Procedure . . . . . . . . . . . .. 115
Component Inspection. . . . . . . . . . . . 116
DTC P1778 STEP MOTOR - FUNCTION
. . . . ... 117
Description . . . . . . . . . . . . . . . ... 117
Diagnostic Procedure . . . . . . . . . . . .. 118
DTC P1791 LINE PRESSURE SENSOR
. . . . . 119
Description . . . . . . . . . . . . . . . ... 119
Wiring Diagram - AT - LPS . . . . . . . . . ..121
Diagnostic Procedure . . . . . . . . . . . ..123
Component Inspection. . . . . . . . . . . .124
. . . . . . . . . . . . 125
Description . . . . . . . . . . . . . . . ...125
Diagnostic Procedure . . . . . . . . . . . ..125
EXCEPT FOR EURO-OBD
VEHICLE SPEED SENSOR CVT (SECONDARY
SPEED SENSOR)
. . . . . . . . . . . . . . 126
Description . . . . . . . . . . . . . . . ...126
Wiring Diagram - AT - VSSA/T . . . . . . . . 128
Diagnostic Procedure . . . . . . . . . . . ..130
. . . . . . . . . ...132
Description . . . . . . . . . . . . . . . ...132
Wiring Diagram - AT - VSSMTR. . . . . . . ..134
Diagnostic Procedure . . . . . . . . . . . ..136
. . . . . . . . 137
Description . . . . . . . . . . . . . . . ...137
Wiring Diagram - AT - TPS. . . . . . . . . ..139
Diagnostic Procedure . . . . . . . . . . . ..141
Component Inspection. . . . . . . . . . . .145
Description . . . . . . . . . . . . . . . ...146
Wiring Diagram - AT - STM . . . . . . . . . .147
Diagnostic Procedure . . . . . . . . . . . ..148
Component Inspection. . . . . . . . . . . .149
. . . . . . . . . ...150
Description . . . . . . . . . . . . . . . ...150
Diagnostic Procedure . . . . . . . . . . . ..150
. . . . . . . . . . 151
Description . . . . . . . . . . . . . . . ...151
Wiring Diagram - AT - LPS . . . . . . . . . ..153
Diagnostic Procedure . . . . . . . . . . . ..155
Component Inspection. . . . . . . . . . . .156
. . . . . ...157
Description . . . . . . . . . . . . . . . ...157
Wiring Diagram - AT - LPSV. . . . . . . . . 159
Diagnostic Procedure . . . . . . . . . . . ..160
Component Inspection. . . . . . . . . . . .163
TORQUE CONVERTER CLUTCH SOLENOID
VALVE
. . . . . . . . . . . . . . . . . . ..164
Description . . . . . . . . . . . . . . . ...164
Wiring Diagram - AT - TCV. . . . . . . . . ..166
Diagnostic Procedure . . . . . . . . . . . ..167
Component Inspection. . . . . . . . . . . .169
CVT FLUID TEMPERATURE SENSOR CIRCUIT
. ..170
Description . . . . . . . . . . . . . . . ...170
Wiring Diagram - AT - FTS . . . . . . . . . ..172
Diagnostic Procedure . . . . . . . . . . . ..174
. . . . . . . . . . . 176
Description . . . . . . . . . . . . . . . ...176
Wiring Diagram - AT - ENGSS . . . . . . . . 177
Diagnostic Procedure . . . . . . . . . . . ..178
CONTROL UNIT (RAM), CONTROL UNIT (ROM)
. .180
Description . . . . . . . . . . . . . . . ...180
Diagnostic Procedure . . . . . . . . . . . ..181
CONTENTS
(Cont’d)
AT-2
. . . . . . . . . ...182
Description . . . . . . . . . . . . . . . ...182
Diagnostic Procedure . . . . . . . . . . . ..183
TROUBLE DIAGNOSES FOR NON-DETECTABLE
ITEMS
. . . . . . . . . . . . . . . . . . ...184
PNP Switch, Stop Lamp Switch and Throttle
Position Switch . . . . . . . . . . . . . . 184
Diagnostic Procedure . . . . . . . . . . . ..184
Wiring Diagram - AT - NONDTC . . . . . . . .188
TROUBLE DIAGNOSES FOR SYMPTOMS
. . . ...192
SPORT Indicator Lamp Does Not Come On . . ..192
. . . . . . . . . . .195
Description . . . . . . . . . . . . . . . ...195
Shift Lock System Electrical Parts Location. . . 195
Wiring Diagram - SHIFT -. . . . . . . . . . 196
Diagnostic Procedure . . . . . . . . . . . ..198
. . . . . . . . . . ..202
Components. . . . . . . . . . . . . . . .202
Removal. . . . . . . . . . . . . . . . ...202
Installation. . . . . . . . . . . . . . . . 203
. . . . . . . . . . . ..204
Control Cable Adjustment. . . . . . . . . . 204
Park/Neutral Position (PNP) Switch Adjustment . .204
Differential Side Oil Seal Replacement . . . . ...204
. . . . . . . ...206
Removal. . . . . . . . . . . . . . . . ...206
Inspection. . . . . . . . . . . . . . . . .206
Installation. . . . . . . . . . . . . . . . 207
Air Breather Hose . . . . . . . . . . . . . 208
CVT Fluid Cooler . . . . . . . . . . . . . .208
Components. . . . . . . . . . . . . . . .209
SERVICE DATA AND SPECIFICATIONS (SDS)
. ...210
General Specifications. . . . . . . . . . . .210
Stall Revolution. . . . . . . . . . . . . . 210
Line Pressure. . . . . . . . . . . . . . ...210
Removal and Installation . . . . . . . . . . .210
A/T Fluid Temperature Sensor. . . . . . . . .210
Solenoid Valves . . . . . . . . . . . . . ...210
Dropping Resistor . . . . . . . . . . . . . 210
CONTENTS
(Cont’d)
AT-3
Alphabetical & P No. Index for DTC
NLAT0001
ALPHABETICAL INDEX FOR DTC
NLAT0001S01
Check if the vehicle is a model with Euro-OBD system or not by the
“Type approval number” on the identification plate. Refer to GI
section, “IDENTIFICATION PLATE”.
Type approval number
Model
Available
With Euro-OBD system
Not available (blank)
Without Euro-OBD system
Items
(CONSULT-II screen terms)
DTC
Reference page
ECM*1
CONSULT-II
GST*2
ATF TEMP SEN/CIRC
0710
P0710
ENG SPEED SIG
0725
P0725
LINE PRESSURE SEN
1791
P1791
L/PRESS SOL/CIRC
0745
P0745
PNP SW/CIRC
0705
P0705
PRI SPEED SIG/CIRC
0715
P0715
STEP MOTOR/CIRC
1777
P1777
STEP MOTOR/FNCTN
1778
P1778
TP SEN/CIRC A/T*3
1705
P1705
TCC SOLENOID/CIRC
0740
P0740
VEH SPD SEN/CIR A/T
0720
P0720
*1: In Diagnostic Test Mode II (Self-diagnostic results), these numbers are controlled by NISSAN.
*2: These numbers are prescribed by ISO15031-6.
*3: When the fail-safe operation occurs, the MI illuminates.
TROUBLE DIAGNOSIS — INDEX
EURO-OBD
Alphabetical & P No. Index for DTC
AT-4
P NO. INDEX FOR DTC
=NLAT0001S02
Check if the vehicle is a model with Euro-OBD system or not by the
“Type approval number” on the identification plate. Refer to GI
section, “IDENTIFICATION PLATE”.
Type approval number
Model
Available
With Euro-OBD system
Not available (blank)
Without Euro-OBD system
DTC
Items
(CONSULT-II screen terms)
Reference page
CONSULT-II
GST*2
ECM*1
P0705
0705
PNP SW/CIRC
P0710
0710
ATF TEMP SEN/CIRC
P0715
0715
PRI SPEED SIG/CIRC
P0720
0720
VEH SPD SEN/CIR AT
P0725
0725
ENG SPEED SIG
P0740
0740
TCC SOLENOID/CIRC
P0745
0745
L/PRESS SOL/CIRC
P1705
1705
TP SEN/CIRC A/T*3
P1777
1777
STEP MOTOR/CIRC
P1778
1778
STEP MOTOR/FNCTN
P1791
1791
LINE PRESSURE SEN
*1: In Diagnostic Test Mode II (Self-diagnostic results), these numbers are controlled by NISSAN.
*2: These numbers are prescribed by ISO15031-6.
*3: When the fail-safe operation occurs, the MI illuminates.
TROUBLE DIAGNOSIS — INDEX
EURO-OBD
Alphabetical & P No. Index for DTC (Cont’d)
AT-5
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT
PRE-TENSIONER”
NLAT0002
The Supplemental Restraint System “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a seat
belt, help to reduce the risk or severity of injury to the driver and front passenger in a frontal collision. The
Supplemental Restraint System consists of air bag modules (located in the center of the steering wheel and
on the instrument panel on the passenger side), seat belt pre-tensioners, a diagnosis sensor unit, warning
lamp, wiring harness and spiral cable.
In addition to the supplemental air bag modules for a frontal collision, the supplemental side air bag used along
with the seat belt helps to reduce the risk or severity of injury to the driver and front passenger in a side col-
lision. The supplemental side air bag consists of air bag modules (located in the outer side of front seats),
satellite sensor, diagnosis sensor unit (one of components of supplemental air bags for a frontal collision),
wiring harness, warning lamp (one of components of supplemental air bags for a frontal collision). Information
necessary to service the system safely is included in the RS section of this Service Manual.
WARNING:
+
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be performed
by an authorized NISSAN dealer.
+
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system.
+
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified with yellow harness connector (and with
yellow harness protector or yellow insulation tape before the harness connectors).
Precautions for On Board Diagnostic (EURO-
OBD) System of CVT and Engine
NLAT0198
The ECM has an on board diagnostic system. It will light up the malfunction indicator lamp (MI) to warn the
driver of a malfunction causing emission deterioration.
CAUTION:
+
Be sure to turn the ignition switch “OFF” and disconnect the negative battery terminal before any
repair or inspection work. The open/short circuit of related switches, sensors, solenoid valves, etc.
will cause the MI to light up.
+
Be sure to connect and lock the connectors securely after work. A loose (unlocked) connector will
cause the MI to light up due to an open circuit. (Be sure the connector is free from water, grease,
dirt, bent terminals, etc.)
+
Be sure to route and secure the harnesses properly after work. Interference of the harness with a
bracket, etc. may cause the MI to light up due to a short circuit.
+
Be sure to connect rubber tubes properly after work. A misconnected or disconnected rubber tube
may cause the MI to light up due to a malfunction of the EGR system or fuel injection system, etc.
+
Be sure to erase the unnecessary malfunction information (repairs completed) from the TCM and
ECM before returning the vehicle to the customer.
SEF289H
Precautions
NLAT0003
+
Before connecting or disconnecting the TCM harness
connector, turn ignition switch OFF and disconnect nega-
tive battery terminal. Failure to do so may damage the
TCM. Because battery voltage is applied to TCM even if
ignition switch is turned off.
PRECAUTIONS
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT BELT PRE-TENSIONER”
AT-6
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст