Nissan Almera Tino V10 (2001 year). Manual — part 135
NEL731
5.
Push “SETTING” switch.
6.
Select “System Setting”.
SEL559X
7.
Select “GPS Information”.
SEL146W
8.
More than one GPS satellite icon turns green. (It may take 1
to 15 minutes.)
NOTE:
Drive the vehicle for a while* in order to change the receiving
condition of the radio wave from the GPS satellite if the GPS
icon does not turn green.
* The driving distance which is necessary depends on the
receiving condition of the radio wave from the GPS satellite.
9.
Push “MAP” switch and check the following.
+
Confirm that the GPS icon on the map turns green.
+
Then the position marker should show the current location.
+
Position marker rotates corresponding to the movement of the
vehicle.
10. Initialization is completed.
NAVIGATION SYSTEM
Confirmation/Adjustment Mode (Cont’d)
EL-415
Control Panel Mode
=NLEL0517
APPLICATION ITEMS
NLEL0517S01
Mode
Description
Reference page
Display Auto Open
Display can be set to open by either of the following controls.
+
Display will be opened when OPEN/CLOSE SW is selected with Key SW positioned
ACC.
+
Display will be automatically opened when Key SW is turned from OFF to ACC.
GPS Information
The GPS data includes longitude, latitude and altitude (distance above sea level) of the
present vehicle position, and current date and time for the area in which the vehicle is
being driven.
Also indicated are the GPS reception conditions and the GPS satellite position.
Language
Language can be selected for the display and voice guidance.
Use the program CD-ROM disk to change the language.
Quick Stop Customer
Setting
One facility of your selection can be added to your Quick Stop.
Route Priorities
Priorities of search request and automatic re-searching can be set for route search.
Tracking
Tracking to the present vehicle position can be displayed.
Display Setting
The following display settings can be customized.
+
Display color (Day mode or Night mode)
+
Brightness of display
Heading
Heading of the map display can be customized for either north heading or the actual
driving direction of the vehicle.
Nearby Display Icons
Icons of facilities can be displayed.
Facilities to be displayed can be selected from the variety selections.
Adjust Current Loca-
tion
Current location of position marker can be adjusted. Direction of position marker also
can be calibrated when heading direction of the vehicle on the display is not matched
with the actual direction.
Avoid Area Setting
A particular area can be avoided when routing.
—
Beep On/Off
Beep sounds which corresponds to the system operation can be activated/deactivated.
Clear Memory
Address book, Previous destination or Avoid area can be deleted.
Country
When two or more countries are included in one CD-ROM disk, the destination can be
selected from the country name.
NEL731
HOW TO PERFORM CONTROL PANEL MODE
NLEL0517S02
1.
Start the engine.
2.
Push “OPEN/CLOSE” switch and then open the display.
3.
Push “SETTING” switch.
+
For further procedures, refer to the following pages which
describe each application item of the control panel mode.
NAVIGATION SYSTEM
Control Panel Mode
EL-416
SEL619X
“DISPLAY AUTO OPEN” MODE
NLEL0517S03
1.
Start the engine.
2.
Push “OPEN/CLOSE” switch and then open the display.
3.
Push “SETTING” switch.
4.
Select “System Setting”.
SEL620X
5.
Select “Display Auto Open”.
SEL621X
6.
Select “Auto” or “Manual” icon.
+
To manually open the display, select “Manual”.
+
To automatically open the display, select “Auto”.
7.
Push “MAP” switch, then the display will go back to the current
location map.
SEL559X
“GPS INFORMATION” MODE
NLEL0517S04
1.
Start the engine.
2.
Push “OPEN/CLOSE” switch and then open the display.
3.
Push “SETTING” switch.
4.
Select “System Setting”.
5.
Select “GPS information”.
SEL146W
6.
Then GPS information will be displayed.
NAVIGATION SYSTEM
Control Panel Mode (Cont’d)
EL-417
SEL565X
“LANGUAGE” MODE
=NLEL0517S05
1.
Start the engine.
2.
Push “OPEN/CLOSE” switch and then open the display.
3.
Push “SETTING” switch.
4.
Select “System Setting”.
5.
Select “Language”.
SEL566X
6.
Select “English” or “German” icon.
+
When display indicates English, select “English”.
+
When display indicates German, select “German”.
7.
Push “MAP” switch, then the display will go back to the current
location map.
NOTE:
Use the program CD-ROM disk to change the language.
SEL543X
“QUICK STOP CUSTOMER SETTING” MODE
NLEL0517S06
1.
Start the engine.
2.
Push “OPEN/CLOSE” switch and then open the display.
3.
Push “SETTING” switch.
4.
Select “System Setting”.
5.
Select “Quick Stop Customer Setting”.
SEL544X
6.
Select an item from the list.
SEL545X
“ROUTE PRIORITIES” MODE
NLEL0517S07
1.
Start the engine.
2.
Push “OPEN/CLOSE” switch and then open the display.
3.
Push “SETTING” switch.
4.
Select “System Setting”.
5.
Select “Route Priorities”.
NAVIGATION SYSTEM
Control Panel Mode (Cont’d)
EL-418
SEL546X
6.
Select an item from the list.
SEL547X
“TRACKING” MODE
NLEL0517S08
1.
Start the engine.
2.
Push “OPEN/CLOSE” switch and then open the display.
3.
Push “SETTING” switch.
4.
Select “System Setting”.
5.
Select “Tracking”.
SEL548X
6.
Select “On” or “Off” icon.
+
To leave no trail on the map, select “Off”.
+
To leave a trail in the map, select “On”.
7.
Push “MAP” switch, then the display will go back to the current
location map.
NOTE:
When a trail display is turned OFF, trail data is erased from the
memory.
SEL560X
SEL561X
“DISPLAY SETTING” MODE
NLEL0517S09
Display Color Setting
NLEL0517S0901
1.
Start the engine.
2.
Push “OPEN/CLOSE” switch and then open the display.
3.
Push “SETTING” switch.
4.
Select “System Setting”.
5.
Select “Color”. Display color will change to Day mode/Night
mode.
6.
Select “MAP” switch, then the display will go back to the cur-
rent location map.
NOTE:
+
Display color can be changed independently when light-
ing switch is turned on and off.
+
Initial setting of the color is as follows:
When lighting switch is turned off: Day mode
When lighting switch is turned on: Night mode
Day mode: White background
Night mode: Black background
NAVIGATION SYSTEM
Control Panel Mode (Cont’d)
EL-419
SEL562X
Brightness Setting
NLEL0517S0902
1.
Start the engine.
2.
Push “OPEN/CLOSE” switch and then open the display.
3.
Push “SETTING” switch.
4.
Select “System Setting”.
5.
Select “Bright” or “Dark” to adjust the brightness of display.
6.
Select “MAP” switch, then the display will go back to the cur-
rent location map.
NOTE:
Display brightness can be adjusted independently when light-
ing switch is turned on and off.
SEL549X
“HEADING” MODE
NLEL0517S10
1.
Start the engine.
2.
Push “OPEN/CLOSE” switch and then open the display.
3.
Push “SETTING” switch.
4.
Select “System Setting”.
5.
Select “Heading”.
SEL550X
6.
Select “Heading up” or “North up” icon.
+
To display North up, select “North up”.
+
To display the car heading up, select “Heading up”.
7.
Push “MAP” switch, then the display will go back to the current
location map.
SEL551X
“NEARBY DISPLAY ICONS” MODE
NLEL0517S11
1.
Start the engine.
2.
Push “OPEN/CLOSE” switch and then open the display.
3.
Push “SETTING” switch.
4.
Select “System Setting”.
5.
Select “Nearby Display Icons”.
NAVIGATION SYSTEM
Control Panel Mode (Cont’d)
EL-420
SEL552X
6.
Select and touch an item on the list.
7.
Push “MAP” switch, then the display will go back to the current
location map.
SEL553X
“ADJUST CURRENT LOCATION” MODE
NLEL0517S12
1.
Start the engine.
2.
Push “OPEN/CLOSE” switch and then open the display.
3.
Push “SETTING” switch.
4.
Select “System Setting”.
5.
Select “Adjust Current Location”.
SEL554X
6.
Select “
” or “
” to calibrate the heading direction.
(Arrow marks will rotate corresponding to the calibration key.)
7.
Select “Set”. Then the vehicle mark will be matched to the
arrow mark.
8.
Display will show “Heading direction has been calibrated” and
then go back to the current location map.
SEL555X
“BEEP ON/OFF” MODE
NLEL0517S13
1.
Start the engine.
2.
Push “OPEN/CLOSE” switch and then open display.
3.
Push “SETTING” switch.
4.
Select “System Setting”.
5.
Touch “Beep On/Off”.
SEL556X
6.
Select “On” or “Off” icon.
+
If you want the beep sound, select “On”.
+
If you do not want the beep sound, select “Off”.
7.
Push “PREVIOUS” switch, then the display will go back to the
current location map.
NAVIGATION SYSTEM
Control Panel Mode (Cont’d)
EL-421
SEL557X
“CLEAR MEMORY” MODE
=NLEL0517S14
1.
Start the engine.
2.
Push “OPEN/CLOSE” switch and then open the display.
3.
Push “SETTING” switch.
4.
Select “System Setting”.
5.
Select “Clear Memory”.
SEL558X
6.
To delete all the stored places in “Address Book”, “Avoid Area”
and “Previous Dest”, select “Yes”.
SEL567X
“COUNTRY” MODE
NLEL0517S15
1.
Start the engine.
2.
Push “OPEN/CLOSE” switch and then open the display.
3.
Push “SETTING” switch.
4.
Select “System Setting”.
5.
Select “Country”.
SEL653X
6.
Select and touch an item on the list.
NAVIGATION SYSTEM
Control Panel Mode (Cont’d)
EL-422
Guide Volume Setting
=NLEL0518
DESCRIPTION
NLEL0518S01
Following voice guidance setting can be changed.
+
Voice guidance activation/deactivation
+
Voice volume of the guidance
SEL563X
ACTIVATION/DEACTIVATION SETTING
NLEL0518S02
1.
Start the engine.
2.
Push “OPEN/CLOSE” switch and then open the display.
3.
Push “SETTING” switch.
4.
The voice prompt can be turned on/off by pressing the “Guid-
ance Volume” button.
SEL563X
VOICE VOLUME SETTING
NLEL0518S03
1.
Start the engine.
2.
Push “OPEN/CLOSE” switch and then open the display.
3.
Push “SETTING” switch.
4.
Volume of the voice can be controlled by bending the joystick
to left/right.
NAVIGATION SYSTEM
Guide Volume Setting
EL-423
Anti-theft System
=NLEL0519
RHD MODELS
NLEL0519S01
Description
By integrating the Navigation System in the vehicle’s interior and linking it to the vehicle’s immobilizer system,
the possibility of the Navigation unit being stolen is effectively reduced. Each time the Navigation System is
switched on, the Navigation System will start up communication with the vehicle’s immobilizer control unit
(IMMU) and verify an identification code. If communication cannot be established, or the verified code is
incorrect, the Navigation System will lock up showing “ANTI-THEFT FUNCTION” on the Navigation display.
The 4-digit PIN must be entered when the display shows “enter your PIN” at the time the vehicle is purchased.
The 4–digit PIN is required to input after disconnecting and reconnecting of battery cable or connectors for
Navigation system.
LHD MODELS
NLEL0519S02
Description
The 4-digit PIN must be entered when the display shows “enter your PIN” at the time the vehicle is purchased.
The 4–digit PIN is required to input after disconnecting and reconnecting of battery cable or connectors for
Navigation system.
NAVIGATION SYSTEM
Anti-theft System
EL-424
SEF094Y
CONSULT-II
=NLEL0520
CONSULT-II INSPECTION PROCEDURE
NLEL0520S01
1.
Turn ignition switch OFF.
2.
Connect CONSULT-II to data link connector.
PBR455D
3.
Insert NVIS (NATS) program card into CONSULT-II.
: Program card
NATS-AEN00B
4.
Turn ignition switch ON.
5.
Touch “START”.
SEL517X
6.
Perform each diagnostic test mode according to each service
procedure.
For further information, see the CONSULT-II Operation
Manual, NATS.
CONSULT-II DIAGNOSTIC TEST MODE FUNCTION
NLEL0520S02
CONSULT-II DIAGNOSTIC TEST
MODE
Description
PIN INITIALIZATION
Navigation system will be locked when the vehicle’s owner enters the wrong PIN five con-
secutive times.
To release the lock, use “PIN INITIALIZATION”.
NAVI ID INITIALIZATION
In normal times regulation codes are being communicated between Navigation Control
Unit and Dongle Control Unit.
Use “NAVI ID INITIALIZATION” to match the codes when either one has been replaced
due to breakdown or etc.
NOTE:
When any initialization is performed, all NAVI ID and PIN pre-
viously registered will be erased and then must be registered
again.
NAVIGATION SYSTEM
CONSULT-II
EL-425
Trouble Diagnoses
=NLEL0521
SYMPTOM CHART
NLEL0521S01
Symptom
Diagnoses/service procedure
Reference
page
Any function of the system
does not operate.
Check power supply and ground circuit for NAVI control unit.
Strange screen color or
unusual screen brightness.
1. Check “Display Setting” MODE.
2. Check display in “Diagnose the Display” MODE.
The display is not dimmed
when turning lighting switch
to ON.
1. Check “Display Setting” MODE.
2. Check lighting switch signal input to NAVI control unit correctly in “Diagnosis for
the signals from the car” MODE.
No navigation guide voice
are heard from front driver
side speaker.
1. Check “Guide Volume Setting”.
2. Check speaker relay.
Beep does not sound when
the system guides route.
Check “Beep On/Off” MODE.
Position marker does not
trace along the route being
traveled.
Go to “WORK FLOW FOR NAVIGATION INSPECTION”.
Position marker does not
indicate forward or backward
movement.
Check reverse signal input to NAVI control unit correctly by “Diagnosis for the sig-
nals from the car” MODE.
Radio wave of GPS cannot
be received. (GPS marker
on the display does not
become green color.)
1. Is there anything obstructing the GPS antenna on the rear parcel finisher?
(GPS antenna located under the rear parcel finisher.)
—
2. Check GPS radio wave receive condition in “GPS Information MODE”.
3. Check GPS antenna in “Self Diagnosis” MODE.
Heading direction of position
marker does not match
vehicle direction.
1. Perform “Adjust Current Location” MODE.
2. Go to “WORK FLOW FOR NAVIGATION INSPECTION”.
Stored location in the
address book and other
memory functions are lost
when battery is disconnected
or becomes discharged.
Stored location in the address book and other memory functions may be lost if the
battery is disconnected or becomes discharged. If this should occur, charge or
replace the battery as necessary and re-enter the information.
—
Map appears grey and can-
not be scrolled.
The current location in the memory is out of the map data area. Perform “Initialize
Location”.
NAVIGATION SYSTEM
Trouble Diagnoses
EL-426
WORK FLOW FOR NAVIGATION INSPECTION
=NLEL0521S02
SEL519X
*1: EL-432
*2: EL-401
*3: EL-404
NAVIGATION SYSTEM
Trouble Diagnoses (Cont’d)
EL-427
DRIVING TEST
=NLEL0521S03
During the driving test, diagnose the system by checking the dif-
ference of symptoms with each sensor ON or OFF.
Test Pattern 1
NLEL0521S0301
Test method in which current position adjustment is not made
according to GPS data.
+
Remove the GPS antenna connector from the NAVI control
unit. Drive the vehicle.
Before driving the vehicle, perform “Adjust Current Location”
MODE (EL-421).
Test Pattern 2
NLEL0521S0302
Test procedure in which map matching is not used.
+
Before driving the vehicle, perform “Adjust Current Location”
MODE (EL-421). With the ignition switch OFF and the map
CD-ROM removed from the NAVI control unit, drive the
vehicle. After driving the vehicle, reinstall the map CD-ROM.
Compare the saved driving tracks for the vehicle’s current loca-
tion with roads on the map.
Example
NLEL0521S0303
<The position marker consistently indicates the wrong position
when driving in the same area. Determine if this is the result of the
map matching function or the GPS function.>
→
Perform test pattern 1.
<To verify the accuracy of the road configuration shown on the
display>
→
Perform test patterns 1 and 2.
+
Compare the map and the saved driving tracks. The precision
of the saved driving tracks is within several hundred meters.
<To make distance calibration and adjustments>
→
Perform test patterns 1 and 2.
+
Make adjustments by driving the vehicle over a known course
(highway or other road where distances are clearly marked).
Calibrate the distance against the known distance. Use the
formula below.
Calibration value = Screen display distance/Actual distance
NAVIGATION SYSTEM
Trouble Diagnoses (Cont’d)
EL-428
NEL705
POWER SUPPLY AND GROUND CIRCUIT CHECK FOR
NAVI CONTROL UNIT
=NLEL0521S04
Power Supply Circuit Check
NLEL0521S0401
Terminal
Ignition switch
(+)
(−)
OFF
ACC
ON
1
Ground
Battery voltage
Battery voltage
Battery voltage
2
Ground
Battery voltage
Battery voltage
Battery voltage
5
Ground
0V
0V
Battery voltage
6
Ground
0V
Battery voltage
Battery voltage
If NG, check the following.
+
10A fuse [No. 1, located in the fuse block (J/B)]
+
10A fuse [No. 10, located in the fuse block (J/B)]
+
15A fuse
+
Harness for open or short between fuse and NAVI control unit
NEL706
Ground Circuit Check
NLEL0521S0402
Terminals
Continuity
3 - Ground
Yes
4 - Ground
Yes
NAVIGATION SYSTEM
Trouble Diagnoses (Cont’d)
EL-429
SPEAKER RELAY CHECK
=NLEL0521S05
1
CHECK RELAY ON SIGNAL
1. Push “VOICE” button.
2. Check voltage between speaker relay terminal 2 and ground.
NEL779
OK or NG
OK
©
GO TO 2.
NG
©
Check harness for open or short between NAVI control unit terminal 46 and speaker
relay terminal 2.
2
CHECK GROUND CIRCUIT FOR SPEAKER RELAY
1. Disconnect speaker relay.
2. Check continuity between speaker relay terminal 1 and ground.
NEL780
OK or NG
OK
©
GO TO 3.
NG
©
Repair harness.
NAVIGATION SYSTEM
Trouble Diagnoses (Cont’d)
EL-430
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст