Nissan Almera Tino V10 (2001 year). Manual — part 116
YEL889B
ILLUMINATION
Wiring Diagram — ILL — (Cont’d)
EL-111
YEL890B
ILLUMINATION
Wiring Diagram — ILL — (Cont’d)
EL-112
MODELS WITH FUSE AND FUSIBLE LINK BOX E90
NLEL0434S02
YEL413C
ILLUMINATION
Wiring Diagram — ILL — (Cont’d)
EL-113
YEL414C
ILLUMINATION
Wiring Diagram — ILL — (Cont’d)
EL-114
YEL415C
ILLUMINATION
Wiring Diagram — ILL — (Cont’d)
EL-115
System Description
NLEL0435
POWER SUPPLY AND GROUND
NLEL0435S01
Power is supplied at all times:
+
through 15A fuse [No. 5, located in the fuse block (J/B)]
+
to time control unit terminal 9,
+
through 10A fuse [No. 12, located in the fuse block (J/B)]
+
to key switch terminal 1 and
+
through 10A fuse [No. 13, located in the fuse block (J/B)]
+
to spot lamp terminal 1, and
+
to interior room lamp terminal 1.
When the key is removed from ignition key cylinder, power is interrupted:
+
through key switch terminal 2
+
to time control unit terminal 22.
With the ignition key switch in the ON or START position, power is supplied:
+
through 10A fuse [No. 10, located in the fuse block (J/B)]
+
to time control unit terminal 1.
Ground is supplied:
+
through body grounds terminals M28 and M48
+
to time control unit terminal 16
When the driver side door is opened, ground is supplied:
+
through body grounds B24 and B30
+
to door switch driver side terminal 3
+
from door switch driver side terminal 2
+
to time control unit terminal 6.
When any door is opened, ground is supplied:
+
through case ground of each door switch
+
to each door switch terminal 1
+
to time control unit terminal 7.
When the driver side door is unlocked, the time control unit receives a ground signal:
+
through body grounds terminals M28 and M48
+
to door unlock sensor terminal 2 (LHD models) or 4 (RHD models)
+
from door unlock sensor terminal 5 (LHD models) or 2 (RHD models)
+
to time control unit terminal 35.
When a signal, or combination of signals is received by the time control unit, ground is supplied:
+
through time control unit terminal 12
+
to spot lamp terminal 2, and
+
to interior room lamp terminal 2.
With power and ground supplied, the interior room lamp and spot lamp illuminates when the lamp switch is
in “DOOR” position.
SWITCH OPERATION
NLEL0435S02
When interior room lamp switch is in “ON” position, ground is supplied:
+
through case grounds of interior room lamp
+
to interior room lamp.
With power and ground supplied, the interior room lamp illuminates.
INTERIOR ROOM LAMP TIMER OPERATION
NLEL0435S03
When interior room lamp switch is in the “DOOR” position, the time control unit keeps the interior room lamp
illuminated for about 30 seconds when:
+
unlock signal is supplied from driver’s door unlock sensor while all doors are closed
+
key is removed from ignition key cylinder while all doors are closed
+
driver’s door is opened and then closed
INTERIOR ROOM LAMP
System Description
EL-116
The timer is canceled when:
+
driver’s door is locked,
+
driver’s door is opened, or
+
ignition switch is turned ON.
ON-OFF CONTROL
NLEL0435S04
When the driver side door, front passenger door, rear LH or RH door is opened, the interior room lamp turns
on while the interior room lamp switch is in the “DOOR” position.
BATTERY SAVER
NLEL0435S11
The interior room lamp is turned OFF automatically with the lamp switch in the “DOOR” position after about
30 minutes, if the lamp remains lit by the door switch open signal.
INTERIOR ROOM LAMP
System Description (Cont’d)
EL-117
Wiring Diagram — ROOM/L —
NLEL0436
MODELS WITH FUSE AND FUSIBLE LINK BOX E43
NLEL0436S01
YEL891B
INTERIOR ROOM LAMP
Wiring Diagram — ROOM/L —
EL-118
YEL892B
INTERIOR ROOM LAMP
Wiring Diagram — ROOM/L — (Cont’d)
EL-119
MODELS WITH FUSE AND FUSIBLE LINK BOX E90
NLEL0436S02
YEL416C
INTERIOR ROOM LAMP
Wiring Diagram — ROOM/L — (Cont’d)
EL-120
YEL417C
INTERIOR ROOM LAMP
Wiring Diagram — ROOM/L — (Cont’d)
EL-121
Trouble Diagnoses
=NLEL0437
DIAGNOSTIC PROCEDURE 1
NLEL0437S01
SYMPTOM: Interior room lamp timer does not operate.
1
CHECK IGNITION ON SIGNAL
Check voltage between time control unit harness connector terminal 1 and ground.
NEL646
OK or NG
OK
©
GO TO 2.
NG
©
Check the following.
+
10A fuse [No. 10, located in fuse block (J/B)]
+
Harness for open or short between time control unit and fuse
2
CHECK DOOR SWITCH INPUT SIGNAL
Check voltage between time control unit harness connector terminal 6 and ground.
NEL647
OK or NG
OK
©
GO TO 4.
NG
©
GO TO 3.
INTERIOR ROOM LAMP
Trouble Diagnoses
EL-122
3
CHECK DRIVER SIDE DOOR SWITCH
Check continuity between door switch terminals 2 and 3.
NEL648
OK or NG
OK
©
Check the following.
+
Driver side door switch ground circuit and condition
+
Harness for open or short between time control unit and driver side door switch
NG
©
Replace driver side door switch.
4
CHECK FRONT DOOR UNLOCK SENSOR INPUT SIGNAL
Check voltage between time control unit harness connector terminal 35 and ground.
NEL649
OK or NG
OK
©
GO TO 6.
NG
©
GO TO 5.
INTERIOR ROOM LAMP
Trouble Diagnoses (Cont’d)
EL-123
5
CHECK FRONT DOOR UNLOCK SENSOR
1. Disconnect front door unlock sensor harness connector.
2. Check continuity between door unlock sensor terminals.
NEL650
OK or NG
OK
©
Check the following.
+
Door unlock sensor ground circuit
+
Harness for open or short between time control unit and door unlock sensor
NG
©
Replace door unlock sensor.
6
CHECK DOOR SWITCHES INPUT SIGNAL
Check voltage between time control unit harness connector terminal 7 and ground.
NEL651
OK or NG
OK
©
GO TO 8.
NG
©
GO TO 7.
INTERIOR ROOM LAMP
Trouble Diagnoses (Cont’d)
EL-124
7
CHECK DOOR SWITCHES
1. Disconnect door switch harness connector.
2. Check continuity between door switch terminal 1 and ground.
NEL652
OK or NG
OK
©
Check the following.
+
Door switch ground condition
+
Harness for open or short between time control unit and door switch
NG
©
Replace door switch.
8
CHECK KEY SWITCH INPUT SIGNAL
Check voltage between time control unit harness connector terminal 22 and ground.
NEL653
OK or NG
OK
©
Replace time control unit.
NG
©
GO TO 9.
INTERIOR ROOM LAMP
Trouble Diagnoses (Cont’d)
EL-125
9
CHECK KEY SWITCH (INSERT)
Check continuity between terminals 1 and 2.
NEL787
OK or NG
OK
©
Check the following.
+
10A fuse [No. 12, located in fuse block (J/B)]
+
Harness for open or short between key switch and fuse
+
Harness for open or short between time control unit and key switch
NG
©
Replace key switch.
DIAGNOSTIC PROCEDURE 2
NLEL0437S02
SYMPTOM: Interior lamp timer does not cancel properly.
1
CHECK IGNITION ON SIGNAL
Check voltage between time control unit harness connector terminal 1 and ground.
NEL646
OK or NG
OK
©
GO TO 2.
NG
©
Check the following.
+
10A fuse [No. 10, located in fuse block (J/B)]
+
Harness for open or short between time control unit and fuse
INTERIOR ROOM LAMP
Trouble Diagnoses (Cont’d)
EL-126
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст