Nissan Primera P11. Manual — part 525
I
Check if shift check groove of fork rod or 5th & reverse check
groove is worn, or has any other abnormalities.
SMT692D
1st & 2nd fork rod
5th & reverse fork rod
3rd & 4th fork rod
REPAIR FOR COMPONENT PARTS
RS5F70A
Shift Control Components (Cont’d)
MT-75
NCMT0023
Clutch Housing
NCMT0023S01
1.
Hammer the striking rod oil seal into clutch housing as far as
it will go.
CAUTION:
Do not reuse striking rod oil seal.
2.
Hammer the differential oil seal into clutch housing until it
becomes flush with clutch housing end face.
CAUTION:
Do not reuse differential oil seal.
3.
Hammer input shaft oil seal into clutch housing as far as it will
go.
CAUTION:
Do not reuse input shaft oil seal.
4.
Hammer the dust seal into clutch housing as far as it will go.
CAUTION:
Do not reuse dust seal.
5.
Install outer race of differential side bearing.
SMT722D
Striking rod
oil seal
SMT723D
Differential oil seal
SMT724D
Input shaft oil seal
SMT725D
Dust seal
SMT726D
Differential side bearing
outer race
ASSEMBLY
RS5F70A
Clutch Housing
MT-76
6.
Install new oil channel (mainshaft).
CAUTION:
Pay attention to installation direction of oil channel.
7.
Align the notches on mainshaft front bearing and transaxle
case. Then, install mainshaft front bearing.
8.
Install mainshaft bearing retainer, and tighten bolts with speci-
fied torque.
9.
Attach boot, striking rod, and striking lever to clutch housing.
And install retaining pin for selector lever.
CAUTION:
I
Before installing striking rod, wrap the end with a vinyl
tape or the like to prevent oil seal from being damaged.
I
Do not reuse retaining pin.
10. Hammer the welch plug (striking lever side) with a general-
purpose drift [OD: 12 mm (0.47 in)].
CAUTION:
Do not reuse welch plug.
SMT727D
Oil channel
SMT728D
Notch on
bearing
Transaxle
case
Mounting direction
of bearing
Mainshaft
front bearing
SMT729D
Mainshaft
bearing retainer
6.3 - 8.3
(0.64 - 0.85, 56 - 74)
N·m (kg-m, in-lb)
SMT667D
Striking lever
SMT730D
Drift
Welch plug
0 - 0.5 mm
(0 - 0.020 in)
Welch plug
Welch plug
drift depth
ASSEMBLY
RS5F70A
Clutch Housing (Cont’d)
MT-77
11. Install selector, selector shaft, and selector shaft pin into clutch
housing.
12. Hammer the welch plug (selector shaft side) with a general-
purpose drift [OD: 12 mm (0.47 in)].
CAUTION:
Do not reuse welch plug.
13. Install selector leaf spring, return spring, steel ball, reverse
gate, selector arm, bushing, and return bearing. Then, tighten
two reamer bolts with specified torque.
CAUTION:
Use correct reamer bolts for each installation point, because
each bolt has a different length.
14. Install oil pocket.
SMT731D
Selector shaft pin
Selector
Welch plug
Selector shaft
SMT732D
Drift
Welch plug
0 - 0.5 mm
(0 - 0.020 in)
Welch plug
drift depth
Welch plug
SMT733D
Reamer bolt
(short)
Selector
leaf spring
Return
spring
Reverse
gate
Steel ball
Reamer bolt
(long)
Bushing
Return bearing
Selector
arm
SMT734D
N·m
(kg-m, ft-lb)
16 - 21
(1.6 - 2.1, 12 - 15)
SMT735D
Oil pocket
ASSEMBLY
RS5F70A
Clutch Housing (Cont’d)
MT-78
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст