Nissan Primera P11. Manual — part 440
Wheel side
●
Install drive shaft into knuckle.
●
Tighten upper knuckle nut and wheel bearing lock nut. Refer
to “FRONT AXLE”, “Wheel Hub and Knuckle”, FA-11.
COMPONENTS
NFA054
Wheel side
(90AC type and 98AC type)
Spacer ring
ABS rotor
Boot band
Drive shaft
Boot
Spider assembly
Circulair clip:
Make sure circular clip is properly meshed with side gear
(transaxle side) and joint assembly (wheel side), and will
not come out.
Be careful not to damage boots. Use suitable protector
or cloth during removal and installation.
All M/T models
Joint assembly
Boot
Circular clip B
Boot band
Snap ring C
Side joint housing
Dust shield
Circular clip
Transaxle side
(GI69 type and GI82 type)
SEC. 391
FRONT AXLE
Drive shaft (Cont’d)
FA-17
p
1
Joint assembly
p
2
Boot band
p
3
Boot
p
4
Circular clip B
p
5
Drive shaft
p
6
Boot band
p
7
Boot
p
8
Snap ring A
p
9
Snap ring B
p
10
Inner race
p
11
Cage
p
12
Ball
p
13
Snap ring C
p
14
Slide joint housing
p
15
Dust shield
p
16
Circular clip A
p
17
Slide joint housing with
extention shaft
p
18
Snap ring E
p
19
Dust shield
p
20
Support bearing
p
21
Support bearing retainer
p
22
Bracket
p
23
Snap ring D
p
24
Dust shield
NFA055
For type with support bearing
Circular clip:
Make sure circular clip is properly meshed with side gear (transaxle
side) and joint assembly (wheel side), and will not come out.
Wheel side (B86 type)
Right drive shaft
Transaxle side (D83/T83 type)
25 - 35 (2.6 - 3.6, 19 - 26)
25 - 35 (2.6 - 3.6, 19 - 26)
43 - 58
(4.4 - 5.9, 32 - 43)
13 - 19 (1.3 - 1.9, 9 - 14)
: N·m (kg-m, ft-lb)
Left drive shaft
All CVT models
Be careful not to damage boots. Use suitable protector
or cloth during removal and installation.
FRONT AXLE
Drive shaft (Cont’d)
FA-18
DISASSEMBLY
TRANSAXLE SIDE (GI69 type and GI82 type)
1. Remove boot bands.
2. Put matching marks on slide joint housing and drive shaft
before separating joint assembly.
3. Put matching marks on spider assembly and drive shaft.
4. Pry off snap ring, then remove spider assembly.
CAUTION:
Do not disassemble spider assembly.
5. Draw out boot.
Cover drive shaft serration with tape to prevent damage to
the boot.
TRANSAXLE SIDE (D83/T83 type)
1. Remove boot bands.
2. Put matchmarks on slide joint housing and inner race, before
separating joint assembly.
3. Remove snap ring “A” with a screwdriver, and pull out slide
joint housing.
4. Put matchmarks on inner race and drive shaft.
5. Remove snap ring “C”, then remove ball cage, inner race and
balls as a unit.
6. Remove snap ring “B”.
7. Draw out boot.
Cover drive shaft serrations with tape so as not to damage
the boot.
WHEEL SIDE (90AC, 98AC and B86 type)
CAUTION:
The joint on the wheel side cannot be disassembled.
●
Before separating joint assembly, put matching marks on
drive shaft and joint assembly.
●
Separate joint assembly with a suitable tool.
Be careful not to damage threads on drive shaft.
●
Remove boot bands and draw out boot.
SFA963
Matching mark
SFA612
Snap ring
SFA476
SFA514A
SFA092A
Suitable tool
(Sliding hammer)
Wheel bearing
lock nut
FRONT AXLE
Drive shaft (Cont’d)
FA-19
SUPPORT BEARING
●
Remove outer dust shield.
●
Remove inner dust shield.
●
Pry off snap ring.
●
Press support bearing assembly out of drive shaft.
●
Press support bearing out of retainer.
SFA613
SFA691
SFA692
Suitable tool
Snap ring
SFA693
SFA617
Suitable tool
FRONT AXLE
Drive shaft (Cont’d)
FA-20
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст