Nissan Primera P11. Manual — part 547
FOR FRONTAL COLLISION
To repair the SRS for a frontal collision, perform the following steps.
When SRS (except the side airbag) is activated in a collision:
p
1
Replace the diagnosis sensor unit.
p
2
Remove the air bag modules (except the side airbag module) and seat belt pre-tensioner assemblies.
p
3
Check the SRS components using the table shown below:
●
Replace any SRS components showing visible signs of damage (dents, cracks, deformation).
p
4
Install new air bag modules (except the side airbag module) and seat belt pre-tensioner assemblies.
p
5
Conduct self-diagnosis using CONSULT-II, and “AIR BAG” warning lamp. Refer to “SRS Operation
Check” for details (RS-37). Ensure entire SRS operates properly.
When SRS is not activated in a collision:
p
1
Check the SRS components using the table shown below:
●
Replace any SRS components showing visible signs of damage (dents, cracks, deformation).
p
2
Conduct self-diagnosis using CONSULT-II, and “AIR BAG” warning lamp. Refer to “SRS Operation
Check” for details (RS-37). Ensure entire SRS operates properly.
SRS inspection
Part
SRS (except the side
air bag) is activated
SRS is NOT activated
Air bag module (driv-
er’s and passenger’s
side)
REPLACE
Install air bag module
with new bolts coated
with bonding agent.
1. Remove air bag module. Check harness cover and connectors for damage, terminals
for deformities, and harness for binding.
2-1. Install driver’s air bag module into the steering wheel to check fit and alignment with
the wheel.
2-2. Install passenger’s air bag module into the instrument panel to check fit with the
instrument panel.
3. No damage found, reinstall with new bolts coated with bonding agent.
4. If damaged—REPLACE. Install airbag modules with new special bolt coated with
bonding agent. Air bag must be deployed before discarding.
Seat belt pre-ten-
sioner assembly
REPLACE
Install seat belt pre-
tensioner with new
bolts coated with
bonding agent.
1. Remove seat belt pre-tensioners.
Check harness cover and connectors for damage, terminals for deformities, and har-
ness for binding.
2. Check belts for damage and anchors for loose mounting.
3. Check retractor for smooth operation.
4. If no damage is found, reinstall with new bolts coated with bonding agent.
5. If damaged—REPLACE. Install the seat belt pre-tensioners with new bolts coated with
bonding agent. Seat belt pre-tensioners must be deployed before discarding.
Diagnosis sensor unit
REPLACE
Install diagnosis sen-
sor unit with new bolts
coated with bonding
agent.
1. Check case and bracket for dents, cracks or deformities.
2. Check connectors for damage, and terminals for deformities.
3. If no damage is found, reinstall with new special bolts and ground bolt coated with
bonding agent.
4. If damaged—REPLACE. Install diagnosis sensor unit with new bolts and ground bolt
coated with bonding agent.
Steering wheel
1. Visually check steering wheel for deformities.
2. Check harness (built into steering wheel) and connectors for damage, and terminals for deformities.
3. Install driver’s air bag module to check fit or alignment with steering wheel.
4. Check steering wheel for excessive free play.
5. If no damage is found, reinstall the steering wheel.
6. If damaged—REPLACE.
Spiral cable
1. Visually check spiral cable and combination switch for damage.
2. Check connectors, flat cable and protective tape for damage.
3. Check steering wheel for noise, binding or heavy operation.
4. If no damage is found, reinstall the spiral cable.
5. If damaged—REPLACE.
Harness and Connec-
tors
1. Check connectors for poor connection, damage, and terminals for deformities.
2. Check harness for binding, chafing, cuts, or deformities.
3. If no damage is found, reinstall harness and connectors.
4. Damaged—REPLACE damaged section of harness. Do not attempt to repair, splice or modify any SRS har-
ness.
Instrument panel
Refer to the table on the next page.
COLLISION DIAGNOSIS
RS-57
Part
SRS (except the
side air bag) is acti-
vated
SRS is NOT activated
Instrument panel
1. When passenger’s air bag inflates, check the following points for bending, deformities or cracks.
●
Opening portion for passenger’s air bag
NRS072
●
Passenger’s air bag module brackets
Back face of instrument panel
NRS079
●
The portions securing the instrument panel
NRS073
2. If no damage is found, reinstall the instrument panel.
3. If damaged—REPLACE the instrument panel with bolts.
Check points
Check points
Check points
COLLISION DIAGNOSIS
RS-58
FOR SIDE COLLISION
To repair the SRS for a side collision, perform the following steps.
When the built-in type front side air bag is activated in the side collision:
p
1
Replace the following components:
− All parts of front seat back (including front seat back frame) with side air bag modules (on the side on
which side air bag is activated)
− Diagnosis sensor unit
− Satellite sensor (on the side on which side air bag is activated)
p
2
Check the SRS components and the related parts using the table shown below.
●
Replace the SRS components and the related parts showing visible signs of damage (dents, cracks,
deformation).
p
3
Conduct self-diagnosis using CONSULT-II, or “AIR BAG” warning lamp. Refer to “SRS Operation Check”
for details (RS-37). Ensure entire SRS operates properly.
When SRS is not activated in the side collision:
p
1
Check the SRS components and the related parts using the table shown below.
●
Replace any SRS components and the related parts showing visible signs of damage (dents, cracks,
deformation).
p
2
Conduct self-diagnosis using CONSULT-II, or “AIR BAG” warning lamp. Refer to “SRS Operation Check”
for details (RS-37). Ensure entire SRS operates properly.
In the case of the side collision
Part
Side air bag is
activated
SRS is NOT activated
Built-in type front
side air bags mod-
ule (LH or RH)
REPLACE all parts
of seat back with
deployed side air
bag module.
1. Check for visible sign of damage (dents, tears, deformation) of the seat back
on the collision side.
2. If damaged—REPLACE the damaged seat parts with new bolts and remove
the side air bag module.
3. Check for visible signs of damage (tears etc.) of the side air bag module.
4. Check harness and connectors for damage, and terminals for deformities.
5. If no damage is found, reinstall the side air bag module with new torx nuts
coated with bonding agent.
6. If damaged—REPLACE the side air bag module with new torx nuts coated
with bonding agent. Air bag must be deployed before disposing of it.
Satellite sensor (LH
or RH)
REPLACE the sat-
ellite sensor on the
collision side with
new nuts.
(Repair the center
pillar inner, etc.
before installing
new one if dam-
aged.)
1. Remove the satellite sensor on the collision side. Check harness connectors
for damage, terminals for deformities, and harness for binding.
2. Check for visible signs of damage (dents, cracks, deformation) of the satel-
lite sensor.
3. Install the satellite sensor to check fit.
4. If no damage is found, reinstall the satellite sensor with new nuts coated with
bonding agent.
5. If damaged—REPLACE the satellite sensor with new nuts coated with bond-
ing agent.
Diagnosis sensor
REPLACE the
diagnosis sensor
unit with the new
bolts.
1. Check case and bracket for dents, cracks or deformities.
2. Check connectors for damage, and terminals for deformities.
3. If no damage is found, reinstall the diagnosis sensor unit with new special
bolts and ground bolt coated with bonding agent.
4. If damaged—REPLACE the diagnosis sensor unit with new special bolts and
ground bolt coated with bonding agent.
Seat belt pre-ten-
sioner assembly
1. Check if the seat belt can be extended smoothly.
If the seat belt cannot be extended smoothly.
− Check for deformities of the center pillar inner.
− If the center pillar inner has no damage, REPLACE the seat belt pre-tensioner assembly.
2. Remove the seat belt pre-tensioner assembly on the collision side. Check harness cover ad con-
nectors for damage, terminals for deformities, and harness for binding.
3. Check for visible signs of damage (dents, cracks, deformation) of the seat belt pre-tensioner
assembly.
4. If no damage is found, reinstall the seat belt pre-tensioner assembly with new bolts coated with
bonding agent.
5. If damaged—REPLACE the seat belt pre-tensioner assembly with new bolts coated with bonding
agent. The seat belt pre-tensioner assembly must be deployed before disposing of it.
COLLISION DIAGNOSIS
RS-59
Part
Side air bag is acti-
vated
SRS is NOT activated
Seat with built-in
type front side air
bag
REPLACE all parts
of seat back
(including seat back
frame)
1. Visually check the seat on the collision side.
2. Remove the seat on the collision side and check the following for damage
and deformities.
●
Harness, connectors and terminals
●
Frame and recliner (for front seat), and also adjuster and slides (for front
seat)
3. If no damage is found, reinstall the seat.
4. If damaged—REPLACE the damaged seat parts with new bolts.
Center pillar inner
1. Check the center pillar inner on the collision side for damage (dents, cracks, deformation).
2. If damaged—REPAIR the center pillar inner.
Trim
1. Check for visible signs of damage (dents, racks, deformation) of the interior trim on the collision
side.
2. If damaged—REPLACE the damaged trim parts.
COLLISION DIAGNOSIS
RS-60
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст