Nissan Primera P11. Manual — part 426
WARNING:
I
Situate vehicle on a flat and solid surface.
I
Place chocks at front and back of rear wheels.
I
Do not remove engine until exhaust system has com-
pletely cooled down.
I
For safety during subsequent steps, the tension of wires
should be slackened against the engine.
I
Before removing front axle from transaxle, place safety
stands under designated front supporting points. Refer to
GI section for lifting points and towing.
I
Be sure to hoist engine and transaxle in a safe manner.
I
For engines not equipped with engine slingers, attach
proper slingers and bolts described in PARTS CATALOG
or Eurofast.
CAUTION:
I
When lifting engine, be careful not to strike adjacent parts,
especially accelerator wire casing, brake lines, and brake
master cylinder.
I
Always use engine slingers when hoisting the engine.
I
When removing drive shaft, be careful not to damage tran-
saxle oil seal.
1.
Remove engine undercovers and splash covers.
2.
Remove front exhaust tube.
3.
Disconnect lower water hose from radiator and drain coolant.
4.
Drain transaxle oil.
5.
Remove power steering mounting bolt. (See left.)
6.
Drain coolant from cylinder head.
7.
Disconnect water hoses and electrical wiring from radiator and
remove radiator.
8.
Disconnect fuel tubes and vacuum tubes.
9.
Release power steering belt adjusting nut and remove power
steering pump from engine.
Bind pump properly to the vehicle.
10. Remove A/C compressor.
11. Disconnect or remove electrical wiring where necessary.
12. Release clutch lever cable.
13. Release tachometer cable from transaxle housing.
14. Remove front wheels.
15. Remove brake caliper mounting bolts and bind caliper properly
to vehicle LH & RH.
.
SEM531D
SEM532D
ENGINE REMOVAL
CD20T
EM-163
16. Disconnect tie rod ball joints and lower ball joints (LH & RH).
17. Remove stabilizer.
18. Remove drive shafts from transaxle.
1)
RH: Split drive shaft center thrust bearing.
2)
RH & LH: Remove hub mounting bolts and remove drive shaft
carefully from transaxle.
19. Mount suitable slingers to cylinder head. Use a suitable hoist
to release the force on the engine mountings.
20. Remove upper mounting (Right side).
21. Release transaxle shift linkages.
22. Release left engine mounting.
SEM534D
SEM535D
SEM536D
ENGINE REMOVAL
CD20T
EM-164
23. Remove center member fixing bolts from chassis.
24. Remove engine with transaxle as shown.
SEM538D
.
SEM247D
ENGINE REMOVAL
CD20T
EM-165
Components
p
1
Piston ring
p
2
Piston
p
3
Piston pin
p
4
Connecting rod bearing
p
5
Connecting rod
p
6
Main bearing cap
p
7
Rear plate
p
8
Flywheel
p
9
Rear oil seal
p
10
Rear oil seal retainer
p
11
Gusset
p
12
Cylinder block
p
13
Main bearing
p
14
Crankshaft
p
15
Main bearing
p
16
Gusset
p
17
Drain plug
p
18
Pilot bushing
p
19
Plate
p
20
Oil jet
NEM376
54 - 74
(5.5 - 7.5,
40 - 54)
83 - 93
(8.5 - 9.5,
61 - 69)
69 - 78 (7.0 - 8.0, 51 - 58)
8.4 - 11.0 (0.86 - 1.12, 74.35 - 97.36)
30 - 40 (3.1 - 4.1, 22 - 30)
Refer to
“Assembly”
: Do not re-use.
: N·m (kg-m, in-lb)
üü
: N·m (kg-m, ft-lb)
ü
: Lubricate with new engine oil.
SEC. 110
⋅
120
30 - 40 (3.1 - 4.1, 22 - 30)
30 - 40 (3.1 - 4.1, 266 - 354)
30 - 40
(3.1 - 4.1, 22 - 30)
16 - 21 (1.6 - 2.1, 12 - 15)
16 - 21 (1.6 - 2.1, 12 - 15)
CYLINDER BLOCK
CD20T
Components
EM-166
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст