Nissan Primera P11. Manual — part 30
Installation
NCAT0116
1.
Tighten bolts fixing transaxle.
Bolt No.
Tightening torque
N
⋅
m (kg-m, ft-lb)
Bolt length “
”
mm (in)
1
70 - 79 (7.1 - 8.1, 51 - 59)
40 (1.57)
2
31 - 36 (3.1 - 3.7, 23 - 26)
35 (1.38)
3
31 - 36 (3.1 - 3.7, 23 - 26)
47 (1.85)
4
70 - 79 (7.1 - 8.1, 52 - 58)
65 (2.56)
2.
Install torque converter to drive plate.
I
With converter installed, rotate crankshaft several turns to
check that transaxle rotates freely without binding.
3.
Reinstall any part removed.
4.
Adjust control cable. Refer to AT-114.
5.
Check continuity of PNP switch. Refer to AT-53.
6.
Refill transaxle with CVT fluid and check fluid level.
7.
Move selector lever through all positions to be sure that tran-
saxle operates correctly. With parking brake applied, idle
engine. A slight shock should be felt through the hand gripping
the selector each time the transaxle is shifted.
8.
Perform road test. Refer to AT-36.
SAT666J
: Transaxle to engine
: Engine to transaxle
SAT638A
REMOVAL AND INSTALLATION
Installation
AT-117
Air Breather Hose
CVT Fluid Cooler (Hyper CVT-M6)
Air duct
Clip
Control cable
Air conditioner tube
Paint mark upside
More than 17 mm insert
Front
Engine harness
Air breather hose
NAT312
SR20DE
Radiator core support (lower)
Radiator
4.5 - 5.7 (0.45 - 0.59)
Bumper retainer
Front
Hose
Upper bracket
Fluid cooler
4.5 - 5.7 (0.45 - 0.59)
: N·m (kg-m)
4.5 - 5.7 (0.45 - 0.59)
Tube
Hose
Radiator
CVT fluid cooler
CVT fluid hydraulic circuit
Side member
Tube
Hose
Radiator shroud
Lower bracket
NAT313
SEC. 310
REMOVAL AND INSTALLATION
Air Breather Hose
AT-118
Components
NAT311
Fluid level gauge
Fluid charging pipe
5.0 - 6.8 (0.5 - 0.7, 44 - 60)
PNP SW
5.0 - 6.8
(0.5 - 0.7, 44 - 60)
Dropping resistor
Secondary pulley speed sensor
5.0 - 6.8
(0.5 - 0.7, 44 - 60)
Speedometer pinion
O-ring
O-ring
Differential
oil seal
Torque converter
Input shaft O-ring
Oil pump
oil seal
CVT assy
Oil pan installation bolt (18)
6.9 - 8.8 (0.7 - 0.9, 61 - 78)
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
: CVT fluid NS-1
Oil pan
Magnet
Drain bolt
30 - 39 (3.0 - 4.0, 22 - 29)
Gasket
Oil pan gasket
4.5 - 5.7 (0.45 - 0.59, 40 - 50)
Tube (inlet)
40 - 58
(4.0 - 6.0,
30 - 43)
Copper washer
4.5 - 5.7
(0.45 - 0.59, 40 - 50)
Tube (outlet)
4.5 - 5.7 (0.45 - 0.59, 40 - 50)
Copper washer
40 - 58 (4.0 - 6.0, 30 - 43)
Primary pulley
speed sensor
5.0 - 6.8 (0.5 - 0.7, 44 - 60)
O-ring
O-ring
4.5 - 5.7 (0.45 - 0.59, 40 - 50)
Differential
oil seal
SEC. 310
⋅
311
⋅
312
⋅
319
REMOVAL AND INSTALLATION
Components
AT-119
General Specifications
NCAT0179
Engine
SR20DE
Automatic transaxle model
RE0F06A
Automatic transaxle assembly
Model code number
8E020
Transaxle gear ratio
D range
Variable
Reverse
1.586
Final drive
5.473
Recommended fluid
Nissan CVT fluid NS-1*1
Fluid capacity
8.1
(7-1/8 Imp qt)
*1: Refer to MA section (“Fluids and Lubricants”, “RECOMMENDED FLUIDS AND LUBRICANTS”).
Any other fluid will damage the CVT.
Stall Revolution
NCAT0181
Engine
Stall revolution
rpm
(SR20DE)
2,350 - 2,850
Line Pressure
NCAT0182
Engine speed
rpm
Line pressure MPa (kg/cm
2
, psi)
R position
D position
L position
Idle
0.6 (6.1, 87)
Stall
4.1 (42, 595)
Removal and Installation
NCAT0197
Unit: mm (in)
Distance between end of converter housing and torque converter
15.9 (0.626) or more
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specifications
AT-120
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст