Nissan Primera P11. Manual — part 209
Overall Inspection Sequence
NCEC0028S0101
*: Refer to EC-SR-46.
SEF104X
INSPECTION
Perform diagnostic test mode II
(Self-diagnostic results).
Repair or replace.
NG
Check ignition timing and idle
speed.
Idle air volume learning.*
COMPLETE
INCOMPLETE
Find reason for incompleteness,
and remove.*
OK
Check heated oxygen sensor 1 (front)
function.
NG
Check heated oxygen sensor 1 (front)
harness.
NG
OK
Check CO%.
NG
OK
INSPECTION END
Check emission control parts and
repair or replace if necessary.
NG
Repair or replace harness.
Replace front heated oxygen
sensor.
Check front heated oxygen
sensor function.
OK
H
BASIC SERVICE PROCEDURE
SR20DE
Idle Speed/Ignition Timing/Idle Mixture Ratio Adjustment (Cont’d)
EC-35
INSPECTION PROCEDURE
NCEC0028S02
1
INSPECTION START
1. Visually check the following:
I
Air cleaner clogging
I
Hoses and duct for leaks
I
Electrical connectors
I
Gasket (intake manifold, cylinder head, exhaust system)
I
Throttle valve and throttle position sensor operation
2. Start engine and warm it up until engine coolant temperature indicator points to the middle of gauge.
Ensure engine speed stays below 1,000 rpm.
SEF935W
3. Open engine hood and run engine at about 2,000 rpm for about 2 minutes under no-load.
4. Perform the Diagnostic Test Mode II (Self-diagnostic results). Refer to EC-SR-61.
SAT652J
OK or NG
OK
©
I
GO TO 2. (With CONSULT-II)
I
GO TO 3. (Without CONSULT-II)
NG
©
1. Repair or replace components as necessary.
2. GO TO 2. (With CONSULT-II)
3. GO TO 3. (Without CONSULT-II)
BASIC SERVICE PROCEDURE
SR20DE
Idle Speed/Ignition Timing/Idle Mixture Ratio Adjustment (Cont’d)
EC-36
2
CHECK IGNITION TIMING
With CONSULT-II
1. Run engine at about 2,000 rpm for about 2 minutes under no-load.
2. Rev engine two or three times under no-load, then run engine at idle speed for about 1 minute.
SEF978U
3. Select “IGNITION TIMING ADJ” in WORK SUPPORT mode.
4. Touch “START”.
PEF546N
5. Rev engine (2,000 to 3,000 rpm) two or three times under no-load, then run engine at idle speed.
6. Check ignition timing with a timing light.
AEC804
15°±2° BTDC
(in “P” or “N” position for CVT)
OK
©
I
GO TO 5. (With CONSULT-II)
I
GO TO 6. (Without CONSULT-II)
NG
©
1. Perform “Idle air volume learning”. Refer to EC-SR-46
2. If still NG, GO TO 4.
BTDC
White painting
BASIC SERVICE PROCEDURE
SR20DE
Idle Speed/Ignition Timing/Idle Mixture Ratio Adjustment (Cont’d)
EC-37
3
CHECK IGNITION TIMING
Without CONSULT-II
1. Run engine at about 2,000 rpm for about 2 minutes under no-load.
2. Rev engine two or three times under no-load, then run engine at idle speed for about 1 minute.
SEF978U
3. Turn off engine and disconnect throttle position sensor harness connector (CVT models only).
SEF197X
4. Start engine and rev it (2,000 to 3,000 rpm) two or three times under no-load, then run engine at idle speed.
5. Check ignition timing with a timing light.
AEC804
15°±2° BTDC
(in “P” or “N” position for CVT)
OK or NG
OK
©
GO TO 5.
NG
©
1. Perform “Idle air volume learning”. Refer to EC-SR-46.
2. If still NG, GO TO 4.
Throttle position
sensor harness
connector
Throttle body
Closed throttle position switch
harness connector (CVT
models)
BTDC
White painting
BASIC SERVICE PROCEDURE
SR20DE
Idle Speed/Ignition Timing/Idle Mixture Ratio Adjustment (Cont’d)
EC-38
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст