Nissan Primera P11. Manual — part 296
Assembly
Apply high-temperature grease to lubricate the bearing, gears
and frictional surface when assembling the starter.
Carefully observe the following instructions.
PINION PROTRUSION LENGTH ADJUSTMENT
Clearance “l”
With pinion driven out by magnetic switch, push pinion back to
remove slack and measure clearance “l” between the front edge
of the pinion and the pinion stopper.
Clearance “l”:
Refer to SDS (EL-52).
Movement “
”
Compare movement “
” in height of pinion when it is pushed out
with magnetic switch energized and when it is pulled out by hand
until it touches stopper.
Movement “
”
Refer to SDS (EL-52).
●
Not in the specified value ... Adjust by selecting the correct
adjusting plate.
SEL026Z
Pinion stopper
Clearance “l”
SEL497D
NEL305
Adjusting plate
STARTING SYSTEM
EL-51
Service Data and Specifications (SDS)
STARTER
Type
M70R
M2T62071
0 001 116 006
MAGNETI MARELLI
MITSUBISHI
BOSCH
Reduction gear type
Reduction gear type
Non-Reduction
Applied model
SR20
CD20T
QG18
QG16
System voltage
V
12
No load
Terminal voltage
V
11.5
11.0
11.5
Current
A
115
Less than 105
Less than 48
Revolution
rev/min
More than 4500
More than 4,030
More than 5,800
Min. commutator dia.
mm (in)
28.8 (1.134)
31.4 (1.236)
33.5 (1.319)
Min. brush of length
mm (in)
5.0 (0.197)
11.5 (0.453)
3.5 (0.138)
Brush spring tension
N (kg, lb)
14.3 - 25.2
(1.46 - 2.57,
3.22 - 5.69)
13.7 - 25.5
(1.4 - 2.6,
3.1 - 5.7)
5.2 (0.53, 1.17)
at 7.5 mm (0.295 in) brush
length
Movement “
” in height of pinion
assembly
mm (in)
—
—
—
Clearance “I” between pinion front
edge & pinion stopper
mm (in)
0 - 3.0 (0 - 0.118)
—
0.0 - 3.9 (0 - 0.154)
Type
S114-806A
S114-871
S13-305
S13-531
S114-800B
HITACHI
Reduction gear type
Applied model
SR20
SR20
with CVT models
CD20T
CD20T
cold area
QG18
⋅
QG16
cold area
System voltage
V
12
No load
Terminal voltage
V
11.0
Current
A
Less than 90
Less than 140
Less than 90
Revolution
rev/min
More than 2,700
More than 2,300
More than 3900
More than 2750
Min. commutator dia.
mm (in)
28.0 (1.102)
35.5 (1.398)
28.0 (1.102)
Min. brush length
mm (in)
10.5 (0.413)
11.0 (0.433)
10.5 (0.413)
Brush spring tension
N (kg, lb)
16.2 (1.65, 3.64)
12.7 - 17.7 (1.29 -
1.80, 2.84, 3.97)
28.4 - 34.3 (2.90 - 3.50, 6.39 - 7.72)
12.7 - 17.7
(1.29 - 1.80,
2.84 - 3.97)
Clearance between bearing &
armature shaft
mm (in)
Less than 0.2 (0.008)
Clearance “I” between pinion front
edge & pinion stopper
mm (in)
0.3 - 2.5
(0.012 - 0.098)
0.3 - 2.0
(0.012 - 0.079)
0.3 - 0.8
(0.012 - 0.031)
0.3 - 2.5
(0.012 - 0.098)
STARTING SYSTEM
EL-52
Wiring Diagram — CHARGE —
GASOLINE ENGINE MODELS
YEL001D
CHARGING SYSTEM
EL-53
DIESEL ENGINE MODELS
YEL002D
CHARGING SYSTEM
Wiring Diagram — CHARGE — (Cont’d)
EL-54
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст