Nissan Primera P11. Manual — part 403
b.
Slide Tool by tapping on the side of the Tool with a hammer.
c.
Remove steel oil pan.
d.
Remove baffle plate.
5.
Remove front exhaust tube.
6.
Set a suitable transmission jack under transaxle and hoist
engine with engine slinger.
7.
Remove center member.
8.
Remove compressor gussets.
9.
Remove rear cover plate.
SEM603E
NEM219
.
Engine
front
.
Baffle plate
SEM045D
Center
member
Transmission jack
.
SEM048D
Front compressor
gusset
Compressor bracket
Rear compressor
gusset
SEM043D
Rear cover plate
OIL PAN
SR20DE
Removal (Cont’d)
EM-71
10. Remove aluminum oil pan bolts.
11. Remove the two engine-to-transaxle bolts and install them into
open bolt holes shown. Tighten the bolts to release aluminum
oil pan from cylinder block.
12. Remove aluminum oil pan.
a.
Insert Tool between cylinder block and aluminum oil pan.
I
Be careful not to damage aluminum mating surface.
I
Do not insert screwdriver, or oil pan flange will be dam-
aged.
b.
Slide Tool by tapping on the side of the Tool with a hammer.
13. Remove the two engine-to-transaxle bolts previously installed
in aluminum oil pan.
SEM044D
Engine
front
Loosen in numercal order.
SEM783E
SEM046D
SEM047D
SEM223D
OIL PAN
SR20DE
Removal (Cont’d)
EM-72
Installation
1.
Install aluminum oil pan.
a.
Before installation use a scraper to remove all traces of liquid
gasket from mating surfaces.
I
Also remove traces of liquid gasket from mating surface of
cylinder block and front cover.
b.
Apply a continuous bead of liquid gasket to mating surface of
aluminum oil pan.
I
Use Genuine Liquid Gasket or equivalent.
I
Be sure liquid gasket diameter is 4.0 to 5.0 mm (0.157 to
0.197 in).
I
Attaching should be done within 5 minutes after coating.
I
For areas marked with “
★
”, apply liquid gasket to the
outer side of the bolt hole.
c.
Install aluminum oil pan.
I
Install bolts in the reverse order of removal.
p
1
-
p
16
bolts:
: 16 - 19 N·m (1.6 - 1.9 kg-m, 12 - 14 ft-lb)
p
17
,
p
18
bolts:
: 8.14 - 9.51 N·m (0.830 - 0.970 kg-m, 72.05 -
84.77 in-lb)
2.
Install the two engine to transaxle bolts.
: 30 - 40 N·m (3.1 - 4.1 kg-m, 22 - 30 ft-lb)
3.
Install rear cover plate.
SEM050D
SEM357E
Cut here.
Liquid gasket
Groove
Bolt hole
7 mm (0.28 in)
.
SEM065D
Tube presser
Liquid gasket
4.0
-
5.0
mm
(0.157
-
0.197
in)
SEM052D
Engine
front
Tighten in numerical order.
SEM224D
Install
Install
OIL PAN
SR20DE
Installation
EM-73
4.
Install compressor gussets.
5.
Install center member.
6.
Install front exhaust tube.
7.
Install baffle plate.
8.
Install steel oil pan.
a.
Before installation, use a scraper to remove all traces of liquid
gasket from mating surfaces.
I
Also remove traces of liquid gasket from mating surface of
aluminum oil pan.
b.
Apply a continuous bead of liquid gasket to mating surface of
steel oil pan.
I
Use Genuine Liquid Gasket or equivalent.
I
Be sure liquid gasket diameter is 4.0 to 5.0 mm (0.157 to
0.197 in).
I
Attaching should be done within 5 minutes after coating.
c.
Install steel oil pan.
I
Tighten bolts in numerical order as shown together with heated
oxygen sensor harness bracket.
I
Wait at least 30 minutes before refilling engine oil.
SEM363D
Front compressor
gusset
Compressor bracket
Rear compressor
gusset
Tighten in numerical order.
NEM220
SEM015E
Cut here.
Liquid gasket
7 mm (0.28 in)
Inner
side
Groove
Bolt hole
NEM221
Liquid gasket
4.0 - 5.0 mm
(0.157 -
0.197 in)
NEM222
p
7
Engine
front
p
3
p
1
p
5
p
9
p
11
p
2
p
4
p
6
p
10
p
8
OIL PAN
SR20DE
Installation (Cont’d)
EM-74
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст