Nissan Rogue (2023 year). Manual in english — page 28

WAF0784X

NOTE:

To operate the active noise cancellation
and active sound enhancement system
properly:

.

Do not cover the speakers or woofer.

.

Do not cover the microphones.

.

Do not change or modify speakers
including the woofer and any audio
related parts such as the amplifier.

.

Do not make any modification includ-
ing sound deadening or modifications
around the microphones, speakers or
woofer.

ACTIVE NOISE CANCELLATION

The active noise cancellation uses micro-
phones

located inside the vehicle to

detect engine booming noises. The sys-
tem then automatically produces a mu-
ted engine booming noise through the
speakers

and woofer

to reduce

engine booming noise.

If the microphones

or the area around

it is tapped, abnormal noise may be
output from the speaker.

ACTIVE SOUND ENHANCEMENT

The active sound enhancement gener-
ates sounds according to engine speed
and driving modes through the speakers

and woofer

to enhance the quality of

the engine sound.

Starting and driving

5-183

ACTIVE NOISE CANCELLATION (if
so equipped)/ACTIVE SOUND
ENHANCEMENT (if so equipped)

6 In case of emergency

Hazard warning flasher switch . . . . . . . . . . . 6-2
Connection to Roadside Assistance . . . . . . . . 6-2
Emergency engine shut off . . . . . . . . . . . . .. 6-3
Flat tire . . . . . . . . . . . . . . . . . . . . . . . . .. 6-3

Tire Pressure Monitoring System (TPMS) . . ... 6-3
Changing a flat tire . . . . . . . . . . . . . . . .. 6-4

Jump starting . . . . . . . . . . . . . . . . . . . .. 6-11
Push starting . . . . . . . . . . . . . . . . . . . . 6-14
If your vehicle overheats . . . . . . . . . . . . . 6-14
Towing your vehicle . . . . . . . . . . . . . . . ... 6-16

Towing recommended by NISSAN . . . . . . 6-17
Vehicle recovery (freeing a stuck vehicle) . .. 6-18

6-2

In case of emergency

SIC2574

Push the switch on to warn other drivers
when you must stop or park under
emergency conditions. All turn signal
lights will flash.

WARNING

.

If stopping for an emergency, be
sure to move the vehicle well off
the road.

.

Do not use the hazard warning
flashers while moving on the
highway unless unusual circum-
stances force you to drive so
slowly that your vehicle might
become a hazard to other traffic.

.

Turn signals do not work when
the hazard warning flasher lights
are on.

The flasher can be actuated with the
ignition switch in any position.

Some state laws may prohibit the use of
the hazard warning flasher switch while
driving.

In the event of a roadside emergency,
Roadside Assistance Service is available
to you. Please refer to your Warranty
Information Booklet (U.S.) or Warranty &
Roadside Assistance Information Booklet
(Canada) for details.

HAZARD WARNING FLASHER SWITCH

CONNECTION TO ROADSIDE ASSISTANCE

To shut off the engine in an emergency
situation while driving, perform the fol-
lowing procedure:

.

Rapidly push the push-button ignition
switch 3 consecutive times in less
than 1.5 seconds, or

.

Push and hold the push-button igni-
tion switch for more than 2 seconds.

TIRE PRESSURE MONITORING SYS-
TEM (TPMS)

This vehicle is equipped with the Tire
Pressure Monitoring System (TPMS). It
monitors tire pressure of all tires except
the spare. When the low tire pressure
warning light is lit, and the “Tire Pressure
Low - Add Air” warning message is
displayed in the vehicle information dis-
play, one or more of your tires is sig-
nificantly under-inflated. If the vehicle is
being driven with low tire pressure, the
TPMS will activate and warn you of it by
the low tire pressure warning light. This
system will activate only when the vehicle
is driven at speeds above 16 MPH (25
km/h). For more details, see “Warning
lights, indicator lights and audible remin-
ders” (P.2-13) and “Tire Pressure Monitor-
ing System (TPMS)” (P.5-6).

WARNING

.

If the low tire pressure warning
light illuminates while driving,
avoid sudden steering maneu-
vers or abrupt braking, reduce
vehicle speed, pull off the road
to a safe location and stop the
vehicle as soon as possible. Driv-
ing with under-inflated tires may
permanently damage the tires

and increase the likelihood of tire
failure. Serious vehicle damage
could occur and may lead to an
accident and could result in ser-
ious personal injury. Check the
tire pressure for all four tires.
Adjust the tire pressure to the
recommended COLD tire pressure
shown on the Tire and Loading
Information label to turn the low
tire pressure warning light OFF. If
the light still illuminates while
driving after adjusting the tire
pressure, a tire may be flat. If
you have a flat tire, replace it with
a spare tire as soon as possible.

.

Since the spare tire is not
equipped with the TPMS, when a
spare tire is mounted or a wheel
is replaced, the TPMS will not
function and the low tire pressure
warning light will flash for ap-
proximately 1 minute. The light
will remain on after 1 minute.
Have your tires replaced and/or
TPMS system reset as soon as
possible. It is recommended you
visit a NISSAN dealer for these
services.

.

Replacing tires with those not
originally specified by NISSAN
could affect the proper operation

In case of emergency

6-3

EMERGENCY ENGINE SHUT OFF

FLAT TIRE

6-4

In case of emergency

of the TPMS.

.

Do not inject any tire liquid or
aerosol tire sealant into the tires,
as this may cause a malfunction
of the tire pressure sensors.

CHANGING A FLAT TIRE

If you have a flat tire, follow the instruc-
tions below.

Stopping the vehicle

1.

Safely move the vehicle off the road
and away from traffic.

2.

Turn on the hazard warning flashers.

3. Park on a level surface and apply the

parking brake.

4. Push the park button to engage the P

(Park) position.

5. Turn off the engine.

6. Raise the hood to warn other traffic,

and to signal professional road assis-
tance personnel that you need assis-
tance.

7.

Have all passengers get out of the
vehicle and stand in a safe place, away
from traffic and clear of the vehicle.

WARNING

.

Make sure the parking brake is
securely applied and the shift
position is placed in the P (Park)
position.

.

Never change tires when the ve-
hicle is on a slope, ice or slippery
areas. This is hazardous.

.

Never change tires if oncoming
traffic is close to your vehicle.
Wait for professional road assis-
tance.

MCE0001A

Blocking wheels

Place suitable blocks

at both the front

and back of the wheel diagonally oppo-
site the flat tire to prevent the vehicle
from moving when it is jacked up.

WARNING

Be sure to block the wheel as the
vehicle may move and result in
personal injury.

WAG0077X

Models with adjustable luggage floor

Getting the spare tire and tools

The jack, jacking tools and the spare tire
are stored in the storage in the luggage
area.

WAG0064X

To remove the jack:

1.

Remove the storage door by pressing
the two release tabs simultaneously.

2.

Turn the jack lever in a counter-clock-
wise direction, and then remove the
jack slowly.

When storing the jack, set the jack slowly
back, then turn the jack lever in a clock-
wise direction until the jack is fixed.

CAUTION

When removing the jack, be careful
that your hands do not hit against
the vehicle. Otherwise, this could
result in personal injury.

NOTE:

.

When storing the jack, do not over-
tighten the jack lever using a screw
driver. Doing so could cause defor-
mation of the installation area for
the jack.

.

Do not allow the jack to contact the
interior parts. Doing so could cause
damage to the vehicle.

In case of emergency

6-5

6-6

In case of emergency

WAG0089X

Models with adjustable luggage floor

Removing the spare tire and tools

The spare tire and tools are located under
the luggage board(s).

To access the storage area:

1.

Remove the luggage floorboard(s).

Models with the adjustable luggage

floor: Release the locks before remov-
ing the rear (outer) luggage board.
(See “Adjustable luggage floor” (P.2-76)
for details.)

Models with the single luggage board:
Disengage the retainer pins. (See “Sin-
gle luggage board” (P.2-75).)

2.

Remove the floor carpet (if so
equipped).

Remove the tools from the tool bag
located in the storage area.

JVE0373X

Remove the spare tire by removing the
clamp holding it.

WAG0067X

Example

Removing the spare tire with sub-
woofer (if so equipped)

1.

To loosen the bolt, turn counterclock-
wise.

2.

Once loosened, remove the bolt.

WAG0068X

Example

3. Place the sub-woofer in the left corner

of the cargo space.

4. Remove the spare tire.

5. Once the flat tire is exchanged with

the spare tire, store the flat tire where
the spare was located.

6. Place the sub-woofer inside the flat

tire.

7.

Turn the bolt clockwise to tighten.

Jacking up the vehicle and remov-
ing the damaged tire

WARNING

.

Never get under the vehicle while
it is supported only by the jack. If
it is necessary to work under the
vehicle, support it with safety
stands.

.

Use only the jack provided with
your vehicle to lift the vehicle. Do
not use the jack provided with
your vehicle on other vehicles.
The jack is designed for lifting
only your vehicle during a tire
change.

.

Use the correct jack-up points.
Never use any other part of the
vehicle for jack support.

.

Never jack up the vehicle more
than necessary.

.

Never use blocks on or under the
jack.

.

Do not start or run the engine
while vehicle is on the jack, as it
may cause the vehicle to move.

.

Do not allow passengers to stay
in the vehicle while it is on the

In case of emergency

6-7

6-8

In case of emergency

jack.

Carefully read the caution label at-
tached to the jack body and the follow-
ing instructions.

JVE0165X

Jack-up point

1.

Place the jack directly under the jack-
up point as illustrated so the top of
the jack contacts the vehicle at the
jack-up point. Align the jack head
between the two notches in the front
or the rear as shown. Also fit the
groove of the jack head between the
notches as shown.

The jack should be used on firm and
level ground.

SCE0504

2.

Loosen each wheel nut one or two
turns by turning it counterclockwise
with the wheel nut wrench.

Do not

remove the wheel nuts until the tire
is off the ground.

3. To lift the vehicle, securely hold the

jack lever and rod with both hands as
shown above. Carefully raise the ve-
hicle until the tire clears the ground.
Remove the wheel nuts, and then
remove the tire.

SCE0933

Installing the spare tire

The spare tire is designed for emer-
gency use. (See specific instructions
under the heading “Wheels and tires”
(P.8-30).)

1.

Clean any mud or dirt from the sur-
face between the wheel and hub.

2.

Carefully put the spare tire on and
tighten the wheel nuts finger tight.
Check that all the wheel nuts contact
the wheel surface horizontally.

3.

With the wheel nut wrench, tighten
wheel nuts alternately and evenly in
the sequence illustrated ( ,

,

,

,

),

more than 2 times, until they are tight.

In case of emergency

6-9

6-10

In case of emergency

4. Lower the vehicle slowly until the tire

touches the ground. Then, with the
wheel nut wrench, tighten the wheel
nuts securely in the sequence illu-
strated. Lower the vehicle completely.

WARNING

.

Incorrect wheel nuts or impro-
perly tightened wheel nuts can
cause the wheel to become loose
or come off. This could cause an
accident.

.

Do not use oil or grease on the
wheel studs or nuts. This could
cause the nuts to become loose.

.

Retighten the wheel nuts when
the vehicle has been driven for
600 miles (1,000 km) (also in
cases of a flat tire, etc.).

.

As soon as possible, tighten the

wheel nuts to the specified torque
with a torque wrench.

Wheel nut tightening torque:

83 ft-lb (113 N·m)

The wheel nuts must be kept tigh-
tened to specifications at all times. It
is recommended that the wheel nuts
be tightened to specifications at

each lubrication interval.

.

Adjust tire pressure to the COLD

pressure.

COLD pressure:

After the vehicle has been parked for
3 hours or more or driven less than 1
mile (1.6 km).

COLD tire pressures are shown on
the Tire and Loading Information
label affixed to the driver side center
pillar.

Stowing the damaged tire and the
tools

1.

Securely store the jack, tools and the
damaged tire in the storage area.

2.

Replace the luggage boards and cov-
er.

3. Close the liftgate.

WARNING

.

Always make sure that the spare
tire and jacking equipment are
properly secured after use. Such
items can become dangerous
projectiles in an accident or sud-
den stop.

.

The spare tire is designed for
emergency use. See specific in-
structions under the heading
“Wheels and tires” (P.8-30).

To start your engine with a booster
battery, the instructions and precautions
below must be followed.

WARNING

.

If done incorrectly, jump starting
can lead to a battery explosion,
resulting in severe injury or
death. It could also damage your
vehicle.

.

Explosive hydrogen gas is always
present in the vicinity of the
battery. Keep all sparks and
flames away from the battery.

.

Do not allow battery fluid to come
into contact with eyes, skin,
clothing or painted surfaces. Bat-
tery fluid is a corrosive sulfuric
acid solution which can cause
severe burns. If the fluid should
come into contact with anything,
immediately flush the contacted
area with water.

.

Keep the battery out of the reach
of children.

.

The booster battery must be
rated at 12 volts. Use of an im-
properly rated battery can da-
mage your vehicle.

.

Whenever working on or near a
battery, always wear suitable eye
protectors (for example, goggles
or industrial safety spectacles)
and remove rings, metal bands,
or any other jewelry. Do not lean
over the battery when jump start-
ing.

.

Do not attempt to jump start a
frozen battery. It could explode
and cause serious injury.

.

Your vehicle has an automatic
engine cooling fan. It could come
on at any time. Keep hands and
other objects away from it.

In case of emergency

6-11

JUMP STARTING

6-12

In case of emergency

WAG0124X

PR25DD engine

WAG0123X

KR15DDT engine

WARNING

Always follow the instructions below.
Failure to do so could result in
damage to the charging system and
cause personal injury.

1.

If the booster battery is in another
vehicle

, position the two vehicles (

and

) to bring their batteries into

close proximity to each other.

Do not allow the two vehicles to
touch.

2.

Apply the parking brake.

3.

Push the park button to engage the P
(Park) position.

4. Switch off all unnecessary electrical

systems (headlights, heater, air condi-
tioner, etc.).

5. Connect jumper cables in the se-

quence as illustrated (

?

?

?

).

CAUTION

.

Always connect positive (+) to
positive (+) and negative (−) to
body ground (for example, as
illustrated), not to the battery.

.

Make sure the jumper cables do
not touch moving parts in the
engine compartment and that
the cable clamps do not contact
any other metal.

6. Start the engine of the booster vehicle

and let it run for a few minutes.

7.

Keep the engine speed of the booster
vehicle

at about 2,000 rpm, and

start the engine of the vehicle

being

jump started.

In case of emergency

6-13

6-14

In case of emergency

CAUTION

Do not keep the starter motor en-
gaged for more than 10 seconds. If
the engine does not start right away,
place the ignition switch in the OFF
position and wait 10 seconds before
trying again.

8. After starting your engine, carefully

disconnect the negative cable and
then the positive cable (

?

?

?

).

Do not attempt to start the engine by
pushing.

CAUTION

.

Continuously Variable Transmis-
sion (CVT) models cannot be
push-started or tow-started. At-
tempting to do so may cause
transmission damage.

.

Three-way catalyst equipped
models should not be started by
pushing since the three way cat-
alyst may be damaged.

.

Never try to start the vehicle by
towing it; when the engine starts,
the forward surge could cause
the vehicle to collide with the
tow vehicle.

WARNING

.

Never continue driving if your
vehicle overheats. Doing so could
cause a vehicle fire.

.

Never open the hood if steam is
coming out.

.

Never remove the radiator or
coolant reservoir cap while the
engine is hot. If the radiator or
coolant reservoir cap is removed
when the engine is hot, pressur-
ized hot water will spurt out and
possibly cause burning, scalding
or serious injury.

.

If steam or coolant is coming
from the engine, stand clear of
the vehicle to prevent getting
burned.

.

The engine cooling fan will start
at anytime when the coolant
temperature exceeds preset de-
grees.

.

Be careful not to allow your
hands, hair, jewelry or clothing
to come into contact with, or to
get caught in the cooling fan or
drive belts.

PUSH STARTING

IF YOUR VEHICLE OVERHEATS

If your vehicle is overheating (indicated by
an extremely high temperature gauge
reading), or if you feel a lack of engine
power, detect abnormal noise, etc., take
the following steps:

1.

Move the vehicle safely off the road
and apply the parking brake.

2.

Push the park button to shift to the P
(Park) position.

Do not stop the engine.

3. Turn off the air conditioner (if so

equipped). Open all the windows,
move the heater or air conditioner
temperature control to maximum hot
and fan control to high speed.

4. Get out of the vehicle. Look and listen

for steam or coolant escaping from
the radiator or coolant reservoir be-
fore opening the hood. (If steam or
coolant is escaping, turn off the en-
gine.) Do not open the hood further
until no steam or coolant can be seen.

5. Open the engine hood.

WARNING

If steam or water is coming from the
engine, stand clear to prevent get-
ting burned.

6. Visually check the drive belt for da-

mage or looseness. Also check if the
cooling fan is running. The radiator
hoses and radiator should not leak
water. If coolant is leaking or the
cooling fan does not run, stop the
engine.

WARNING

Be careful not to allow your hands,
hair, jewelry or clothing to come into
contact with, or get caught in, engine
belts or the engine cooling fan. The
engine cooling fan can start at any
time.

7.

After the engine cools down, check
the coolant level in the reservoir with
the engine running. Add coolant to
the reservoir if necessary. Have your
vehicle repaired. It is recommended
you visit a NISSAN dealer for this
service.

In case of emergency

6-15