Nissan Rogue (2023 year). Manual in english — page 31
CLEANING
If your windshield is not clear after using
the windshield washer or if a wiper blade
chatters when running, wax or other
material may be on the blade or wind-
shield.
Clean the outside of the windshield with a
washer solution or a mild detergent. Your
windshield is clean if beads do not form
when rinsing with clear water.
Clean each blade by wiping it with a cloth
soaked in a washer solution or a mild
detergent. Then rinse the blade with clear
water. If your windshield is still not clear
after cleaning the blades and using the
wiper, replace the blades.
CAUTION
Worn windshield wiper blades can
damage the windshield and impair
driver vision.
When a washer nozzle is clogged
It is recommended you see a NISSAN
dealer if a washer nozzle is clogged or
any malfunction occurs. Do not attempt
to clean the nozzle using a needle or a
pin. Doing so may damage the nozzle.
WAI0163X
REPLACING
Replace the wiper blades if they are worn.
1.
Lift the wiper arm away from the
windshield.
2.
Open
, using a suitable tool, and then
move the wiper blade down as shown
to remove.
3.
Insert the new wiper blade onto the
wiper arm until a click sounds.
4. Close
.
CAUTION
.
After wiper blade replacement,
return the wiper arm to its origi-
nal position; otherwise it may be
damaged when the hood is
opened.
.
Make sure the wiper blades con-
tact the glass; otherwise the arm
may be damaged from wind
pressure.
Do-it-yourself
8-21
WINDSHIELD WIPER BLADES
-------------------------------------------------------------------------------------------------------------------------------------------------------------
8-22
Do-it-yourself
It is recommended you contact a NISSAN
dealer if checking or replacement is
required.
If the brakes do not operate properly, it is
recommended you have the brakes
checked by a NISSAN dealer.
SELF-ADJUSTING BRAKES
Your vehicle is equipped with self-adjust-
ing brakes.
The disc-type brakes self-adjust every
time the brake pedal is applied.
WARNING
Have your brake system checked if
the brake pedal height does not
return to normal. It is recommended
you visit a NISSAN dealer for this
service.
BRAKE PAD WEAR WARNING
The disc brake pads have audible wear
warnings. When a brake pad requires
replacement, it will make a high pitched
scraping sound when the vehicle is in
motion. This scraping sound will first
occur only when the brake pedal is
depressed. After more wear of the brake
pad, the sound will always be heard even
if the brake pedal is not depressed. Have
the brakes checked as soon as possible if
the wear warning sound is heard.
Under some driving or climate conditions,
occasional brake squeak, squeal or other
noise may be heard. Occasional brake
noise during light to moderate stops is
normal and does not affect the function
or performance of the brake system.
Proper brake inspection intervals
should be followed.
For additional infor-
mation, see the maintenance schedule
shown in the “9. Maintenance and sche-
dules” section.
REAR WINDOW WIPER BLADE
BRAKES
-------------------------------------------------------------------------------------------------------------------------------------------------------------
WAI0124X
ENGINE COMPARTMENT
WARNING
Never use a fuse of a higher or lower
amperage rating than that specified
on the fuse box cover. This could
damage the electrical system or
electronic control units or cause a
fire.
If any electrical equipment does not
operate, check for an open fuse.
1.
Be sure the ignition switch is turned
off and the headlights are off.
2.
Open the engine hood.
3.
Remove the fuse/fusible link box cov-
er by using a suitable tool and pushing
the tab.
4. Locate the fuse that needs to be
replaced.
5. Remove the fuse using the fuse puller
located in the passenger compart-
ment fuse box.
SDI1753
6. If the fuse is open
, replace it with a
new fuse
.
7.
If a new fuse also opens, have the
electrical system checked and re-
paired. It is recommended you visit a
NISSAN dealer for this service.
Fusible links
If any electrical equipment does not
operate and the fuses are in good condi-
tion, check the fusible links. If any of these
fusible links are melted, replace only with
genuine NISSAN parts.
For checking and replacing the fusible
links, it is recommended you visit a
NISSAN dealer.
Do-it-yourself
8-23
FUSES
-------------------------------------------------------------------------------------------------------------------------------------------------------------
8-24
Do-it-yourself
WAI0205X
PASSENGER COMPARTMENT
WARNING
Never use a fuse of a higher or lower
amperage rating than that specified
on the fuse box cover. This could
damage the electrical system or
electronic control units or cause a
fire.
If any electrical equipment does not
operate, check for an open fuse.
1.
Be sure the ignition switch is turned
off and the headlights are off.
2.
Remove the fuse box cover.
3.
Remove the fuse with the fuse puller
.
SDI1753
4. If the fuse is open
, replace it with a
new fuse
.
5. If a new fuse also opens, have the
electrical system checked and re-
paired. It is recommended you visit a
NISSAN dealer for this service.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
WAI0271X
Extended storage switch (if so
equipped)
The extended storage switch is used
when shipping the vehicle. It is located
in the fuse panel on the driver’s side of the
instrument panel. If any electrical equip-
ment does not operate, ensure the ex-
tended storage switch is pushed fully in
place.
To inspect the extended storage switch,
ensure the ignition switch and headlights
are off.
How to remove the extended storage
switch:
1.
To remove the extended storage
switch, be sure the ignition switch is
in the OFF or LOCK position.
2.
Be sure the headlights are off. (See
“Headlight switch” (P.2-58) or “Intelli-
gent Auto Headlight system” (P.2-59).)
3. Remove the fuse box cover.
4. Pinch the locking tabs
on top and
bottom of the extended storage
switch.
5. Pull the extended storage switch
straight out from the fuse box
.
CAUTION
.
Be careful not to allow children to
swallow the battery and removed
parts.
.
An improperly disposed battery
can harm the environment. Al-
ways confirm local regulations
for battery disposal.
.
When changing batteries, do not
let dust or oil get on the compo-
nents.
.
There is danger of explosion if the
lithium battery is incorrectly re-
placed. Replace only with the
same or equivalent type.
Do-it-yourself
8-25
INTELLIGENT KEY BATTERY REPLACEMENT
-------------------------------------------------------------------------------------------------------------------------------------------------------------
8-26
Do-it-yourself
WAI0382X
Replace the battery in the Intelligent Key
as follows:
1.
Remove the mechanical key from the
Intelligent Key.
2.
Insert a small screwdriver into the slit
(on the right and left sides) and twist it
to separate the upper part from the
lower part. Use a cloth to protect the
casing.
3.
Replace the battery with a new one.
Recommended battery:
CR2032 or equivalent
.
Do not touch the internal circuit
and electric terminals as doing so
could cause a malfunction.
.
Hold the battery by the edges.
Holding the battery across the
contact points will seriously deplete
the storage capacity.
.
Make sure that the
+
side faces the
bottom of the case.
WBI0015X
4. Align the tips of the upper and lower
parts, and then push them together
until it is securely closed.
5. Operate the buttons to check its
operation.
If you need any assistance for replace-
ment, it is recommended you visit a
NISSAN dealer for this service.
FCC Notice:
For USA:
FCC ID : KR5TXPZ1
FCC ID : KR5TXPZ3
FCC ID : KR5HFM401
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
-------------------------------------------------------------------------------------------------------------------------------------------------------------
following two conditions: (1) This device
may not cause harmful interference,
and (2) this device must accept any
interference received, including inter-
ference that may cause undesired op-
eration.
Note: Changes or modifications not
expressly approved by the party re-
sponsible for compliance could void
the user’s authority to operate the
equipment.
For Canada:
IC ID : 7812D-TXPZ3
IC ID : 7812D-HFM401
This device contains licence-exempt
transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt
RSS(s). Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause interference. (2) This
device must accept any interference,
including interference that may cause
undesired operation of the device.
Do-it-yourself
8-27
-------------------------------------------------------------------------------------------------------------------------------------------------------------
8-28
Do-it-yourself
WAI0201X
1.
Front map light
2.
Vanity mirror light (if so equipped)
3.
Room light (if so equipped)
4.
Side turn signal light
5.
Rear personal light (if so equipped)
6.
Headlight (high-beam)
7.
Front fog light (if so equipped)
8.
Headlight (low-beam)
9.
Front parking light/Daytime running
light/Front turn signal light (LED type)
10.
Front turn signal light (Bulb type)
11.
Front side marker light
12.
High-mounted stop light
13.
Cargo light
14.
License plate light
15.
Back-up light/Tail light
16.
Rear turn signal light/Stop light/Tail light
17.
Rear side marker light
LIGHTS
-------------------------------------------------------------------------------------------------------------------------------------------------------------
HEADLIGHTS
Fog may temporarily form inside the lens
of the exterior lights in the rain or in a car
wash. A temperature difference between
the inside and the outside of the lens
causes the fog. This is not a malfunction.
If large drops of water collect inside the
lens, it is recommended you visit a NISSAN
dealer for servicing.
Replacing
If LED headlight replacement is required,
it is recommended that you visit a NISSAN
dealer for this service.
EXTERIOR AND INTERIOR LIGHTS
Item
Wattage (W)
Bulb No.
Headlight high/low beams*
LED
-
Front turn signal light*
28/8 or LED
7444NA or -
Front parking light*
LED
-
Front side marker light*
5
W5W
Front fog light (if so equipped)*
LED
-
Side turn signal light (if so equipped)*
LED
-
Daytime running light*
LED
-
Rear combination light*
Turn signal light
21
W21W
Stop/tail light
LED
—
Back-up
16
W16W
Rear side marker light*
5
W5W
License plate light*
5 (assembly)
W5W
Map light*
8
W8W
Rear personal light (if so equipped)*
5
W5W
Vanity mirror light (if so equipped)*
5
W5W
High-mounted stop light*
LED
-
Room light (if so equipped)*
8
W8W
Cargo light
8
-
Lower center light (if so equipped)*
1.4 or LED
-
Console box light*
1.4 or LED
-
*:
It is recommended you visit a NISSAN dealer for replacement.
NOTE: It is recommended that you check with the Parts Department at a NISSAN dealer for the
latest information about parts.
Do-it-yourself
8-29
-------------------------------------------------------------------------------------------------------------------------------------------------------------
8-30
Do-it-yourself
SDI2306
:
REMOVE
:
INSTALL
Replacement procedures
All other lights are either type A, B, C, D or
E. When replacing a bulb, first remove the
lens and/or cover.
WAI0202X
Cargo light
If you have a flat tire, see “Flat tire” (P.6-
3).
TIRE PRESSURE
Tire Pressure Monitoring System
(TPMS)
This vehicle is equipped with the Tire
Pressure Monitoring System (TPMS). It
monitors tire pressure of all tires except
the spare. When the low tire pressure
warning light is lit, and the “Tire Pressure
Low - Add Air” warning message is
displayed in the vehicle information dis-
play, one or more of your tires is sig-
nificantly under-inflated.
The TPMS will activate only when the
vehicle is driven at speeds above 16 MPH
(25 km/h). Also, this system may not
detect a sudden drop in tire pressure
(for example a flat tire while driving).
For more details, see “Low tire pressure
warning light” (P.2-18), “Tire Pressure Mon-
itoring System (TPMS)” (P.5-6) and “Tire
Pressure Monitoring System (TPMS)” (P.6-
3).
WHEELS AND TIRES
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Tire inflation pressure
Check the pressure of the tires
(including the spare) often and al-
ways prior to long distance trips.
The recommended tire pressure
specifications are shown on the
Tire and Loading Information label
under the “Cold Tire Pressure”
heading. The Tire and Loading In-
formation label is affixed to the
driver side center pillar. Tire pres-
sures should be checked regularly
because:
.
Most tires naturally lose air over
time.
.
Tires can lose air suddenly when
driven over potholes or other
objects or if the vehicle strikes
a curb while parking.
The tire pressures should be
checked when the tires are cold.
The tires are considered COLD after
the vehicle has been parked for 3 or
more hours, or driven less than 1
mile (1.6 km) at moderate speeds.
TPMS with Easy Fill Tire Alert pro-
vides visual and audible signals
outside the vehicle for inflating the
tires to the recommended COLD
tire pressure. (See “TPMS with Easy
Fill Tire Alert” (P.5-9).)
Incorrect tire pressure, including
under inflation, may adversely
affect tire life and vehicle hand-
ling.
WARNING
.
Improperly inflated tires can
fail suddenly and cause an
accident.
.
The Gross Vehicle Weight
rating (GVWR) is located on
the F.M.V.S.S./C.M.V.S.S. cer-
tification label. The vehicle
weight capacity is indicated
on the Tire and Loading In-
formation label. Do not load
your vehicle beyond this ca-
pacity. Overloading your ve-
hicle may result in reduced
tire life, unsafe operating
conditions due to premature
tire failure, or unfavorable
handling characteristics
and could also lead to a
serious accident. Loading
beyond the specified capa-
city may also result in failure
of other vehicle compo-
nents.
.
Before taking a long trip, or
whenever you heavily load
your vehicle, use a tire pres-
sure gauge to ensure that
the tire pressures are at the
specified level.
.
For additional information
regarding tires, refer to “Im-
portant Tire Safety Informa-
tion” (US) or “Tire Safety
Information” (Canada) in the
Warranty Information Book-
let.
Do-it-yourself
8-31
-------------------------------------------------------------------------------------------------------------------------------------------------------------
8-32
Do-it-yourself
SDI2503
Tire and Loading Information label
Seating capacity: The max-
imum number of occu-
pants that can be seated
in the vehicle.
Vehicle load limit: See “Ve-
hicle loading information”
(P.10-16).
Original size: The size of
the tires originally installed
on the vehicle at the fac-
tory.
Cold tire pressure: Inflate
the tires to this pressure
when the tires are cold.
Tires are considered COLD
after the vehicle has been
parked for 3 or more hours,
or driven less than 1 mile
( 1 . 6
k m )
a t
m o d e r a t e
speeds. The recommended
cold tire inflation is set by
the manufacturer to pro-
vide the best balance of
tire wear, vehicle handling,
driveability, tire noise, etc.,
up to the vehicle’s GVWR.
Tire size — see “Tire label-
ing” (P.8-34).
Spare tire size or compact
spare tire size
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SDI1949
Checking the tire pressure
1. Remove the valve stem cap from
the tire.
2.
P r e s s t h e p r e s s u r e g a u g e
squarely onto the valve stem.
Do not press too hard or force
the valve stem sideways, or air
will escape. If the hissing sound
of air escaping from the tire is
heard while checking the pres-
sure, reposition the gauge to
eliminate this leakage.
3.
Remove the gauge.
4.
Read the tire pressure on the
gauge stem and compare it to
the specification shown on the
Tire and Loading Information
label.
5.
Add air to the tire as needed. If
too much air is added, press the
core of the valve stem briefly
with the tip of the gauge stem to
release pressure. Recheck the
pressure and add or release air
as needed.
6.
Install the valve stem cap.
7.
Check the pressure of all other
tires, including the spare.
Do-it-yourself
8-33
-------------------------------------------------------------------------------------------------------------------------------------------------------------
8-34
Do-it-yourself
SIZE
COLD TIRE INFLATION PRESSURE
PSI
kPa
FRONT ORIGINAL
TIRE:235/65 R17
36
250
FRONT ORIGINAL
TIRE:235/60 R18
33
230
FRONT ORIGINAL
TIRE:235/55 R19
33
230
REAR ORIGINAL
TIRE:235/65 R17
33
230
REAR ORIGINAL
TIRE:235/60 R18
30
210
REAR ORIGINAL
TIRE:235/55 R19
30
210
SPARE TIRE:T155/80
D17 (2WD)
60
420
SPARE TIRE:T165/90
D17 (AWD)
60
420
SDI1575
Example
TIRE LABELING
Federal law requires tire manufac-
turers to place standardized infor-
mation on the sidewall of all tires.
This information identifies and de-
scribes the fundamental character-
istics of the tire and also provides
the tire identification number (TIN)
for safety standard certification.
The TIN can be used to identify
the tire in case of a recall.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SDI1606
Example
Tire size (example: P215/60R16
94H)
1. P: The “P” indicates the tire is
designed for passenger vehicles.
(Not all tires have this informa-
tion.)
2. Three-digit number (215): This
number gives the width in milli-
meters of the tire from sidewall
edge to sidewall edge.
3. Two-digit number (60): This
number, known as the aspect
ratio, gives the tire’s ratio of
height to width.
4. R: The “R” stands for radial.
5. Two-digit number (16): This
number is the wheel or rim
diameter in inches.
6. Two- or three-digit number (94):
This number is the tire’s load
index. It is a measurement of
how much weight each tire can
support. You may not find this
information on all tires because
it is not required by law.
7. H: Tire speed rating. You should
not drive the vehicle faster than
the tire speed rating.
JVM0694X
Example (Type A) (if so equipped)
TIN (Tire Identification Number)
for a new tire (example: DOT XX XX
XXX XXXX)
1. DOT: Abbreviation for the “De-
partment of Transportation”.
The symbol can be placed
above, below or to the left or
right of the Tire Identification
Number.
2. Two-digit code: Manufacturer’s
identification mark
3. Two-digit code: Tire size
Do-it-yourself
8-35
-------------------------------------------------------------------------------------------------------------------------------------------------------------
8-36
Do-it-yourself
4. Three-digit code: Tire type code
(Optional)
5. Four numbers represent the
week and year the tire was built.
For example, the numbers 3103
means the 31st week of 2003. If
these numbers are missing, then
look on the other sidewall of the
tire.
WAI0339X
Example (Type B) (if so equipped)
T I N
( T i r e
I d e n t i f i c a t i o n
Number) for a new tire
(example: DOT XXX XXXXXX
XXXX)
1. DOT: Abbreviation for the “De-
partment of Transportation”.
The symbol can be placed
above, below or to the left or
right of the Tire Identification
Number.
2. Three-digit code: Manufacturer’s
identification mark
3. Six-digit code: Descriptive code
used to identify significant char-
acteristics of the tire.
4. Four numbers represent the
week and year the tire was built.
For example, the numbers 3103
means the 31st week of 2003.
Tire ply composition and materi-
al
The number of layers or plies of
rubber-coated fabric in the tire.
Tire manufacturers also must in-
dicate the materials in the tire,
which include steel, nylon, polye-
ster, and others.
Maximum permissible inflation
pressure
This number is the greatest
amount of air pressure that should
be put in the tire. Do not exceed the
maximum permissible inflation
pressure.
Maximum load rating
This number indicates the maxi-
mum load in kilograms and pounds
that can be carried by the tire.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст