Nissan Pathfinder (2022 year). Manual in english — page 35
7. Finally, lift the windshield wiper and
washer lever to the mist position
O
D
once and release. This action will cause
the wipers to resume the set position.
CAUTION
•
After wiper blade replacement, re-
turn the wiper arm to its original po-
sition; otherwise it may be damaged
when the hood is opened.
•
Make sure the wiper blades contact
the glass; otherwise the arms may be
damaged from wind pressure.
If you wax the surface of the hood, be care-
ful not to let wax get into the washer nozzle
O
F
. This may cause clogging or improper
windshield-washer operation. If wax gets
into the nozzle, remove it with a needle or
small pin
O
E
.
Rear window wiper blade
If checking or replacement is required, it is
recommended that you visit a NISSAN
dealer for this service.
LDI3600
LDI3189
8-20
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
If the brakes do not operate properly have
the brakes checked. It is recommended
that you visit a NISSAN dealer for this
service.
Self-adjusting brakes
Your vehicle is equipped with self-adjusting
brakes.
The front and rear disc-type brakes self-
adjust every time the brake pedal is
applied.
WARNING
Have your brake system checked if the
brake pedal height does not return to
normal. It is recommended that you
visit a NISSAN dealer for this service.
Brake pad wear indicators
The disc brake pads on your vehicle have
audible wear indicators. When a brake pad
requires
replacement,
a
high
pitched
scraping or screeching sound will be heard
when the vehicle is in motion. The noise will
be heard whether or not the brake pedal is
depressed. Have the brakes checked as
soon as possible if the wear indicator
sound is heard.
Under some driving or climate conditions,
occasional brake squeak, squeal or other
noise may be heard. Occasional brake
noise during light to moderate stops is nor-
mal and does not affect the function or
performance of the brake system.
Proper brake inspection intervals should
be followed.
For additional information re-
garding brake inspections, see appropriate
maintenance schedule information in the
"Maintenance and schedules" section of
this manual.
If any electrical equipment does not oper-
ate, check for an open fuse.
Fuses are used in the passenger and en-
gine compartment. Spare fuses are pro-
vided and can be found in the passenger
compartment fuse box.
When installing a fuse make sure the fuse is
installed in the fuse box securely.
LDI2997
BRAKES
FUSES
Do-it-yourself
8-21
-------------------------------------------------------------------------------------------------------------------------------------------------------------
ENGINE COMPARTMENT
WARNING
Never use a fuse of higher or lower am-
perage rating than that specified on
the fuse box cover. This could damage
the electrical system or electronic con-
trol units or cause a fire.
If any electrical equipment does not come
on, check for an open fuse.
1. Be sure the ignition switch and the head-
light switch are OFF.
2. Open the engine hood.
3. Remove the fuse box cover by pushing
the tab and lifting the cover up.
4. Remove the fuse with the fuse puller.
The fuse puller is located in the fuse
block in the passenger compartment.
5. If the fuse is open
O
A
, replace it with a
new fuse
O
B
.
6. If a new fuse also opens, have the elec-
trical system checked and repaired. It is
recommended that you visit a NISSAN
dealer for this service.
Fusible links
If the electrical equipment does not oper-
ate and fuses are in good condition, check
the fusible links. If any of these fusible links
are melted, replace with only Genuine
NISSAN parts.
LDI3584
LDI3200
8-22
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PASSENGER COMPARTMENT
WARNING
Never use a fuse of higher or lower am-
perage rating than that specified on
the fuse box diagram. This could dam-
age the electrical system or electronic
control units or cause a fire.
If any electrical equipment does not oper-
ate, check for an open fuse.
1. Be sure the ignition switch and the head-
light switch are OFF.
2. Remove the fuse with the fuse puller.
3. If the fuse is open
O
A
, replace it with an
equivalent good fuse
O
B
.
4. If a new fuse also opens, have the elec-
trical system checked and repaired. It is
recommended that you visit a NISSAN
dealer for this service.
LDI3586
LDI3200
Do-it-yourself
8-23
-------------------------------------------------------------------------------------------------------------------------------------------------------------
LDI3613
8-24
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
CAUTION
Be careful not to allow children to swal-
low the battery or removed parts.
NISSAN INTELLIGENT KEY®
Replace the battery in the Intelligent Key as
follows:
1. Remove the mechanical key from the
Intelligent Key.
2. Insert a small flathead screwdriver
O
A
into the slit
O
B
of the corner and twist it
to separate the upper part from the
lower part. Place a cloth over the screw-
driver to protect the casing.
LDI2001
BATTERY REPLACEMENT
Do-it-yourself
8-25
-------------------------------------------------------------------------------------------------------------------------------------------------------------
3. Replace the battery with a new one.
Recommended
battery:
CR2032
or
equivalent.
• Do not touch the internal circuit and
electric terminals as doing so could
cause a malfunction.
• Hold the battery by the edges. Holding
the battery across the contact points
will seriously deplete the storage
capacity.
• Make sure that the + side faces the
bottom of the lower part.
4. Close the lid securely as illustrated with
O
C
and
O
D
.
5. Operate the buttons to check the
operation.
If you need assistance with replacement, it
is recommended that you visit a NISSAN
dealer for this service.
FCC Notice:
For USA:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interfer-
ence received, including interference
that may cause undesired operation.
Note:
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s author-
ity to operate the equipment.
For Canada:
This
device
contains
licence-exempt
transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt
RSS(s). Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause interference. (2) This de-
vice must accept any interference, in-
cluding interference that may cause un-
desired operation of the device.
LDI2637
8-26
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
HEADLIGHTS
For additional information on headlight
bulb replacement, refer to the instructions
outlined in this section.
Replacing the LED headlight bulb
If LED headlight bulb replacement is re-
quired, it is recommended that you visit a
NISSAN dealer for this service.
FOG LIGHTS (if so equipped)
For additional information on fog light bulb
replacement, refer to the instructions out-
lined in this section.
Replacing the LED fog light bulb
If LED fog light bulb replacement is re-
quired, it is recommended that you visit a
NISSAN dealer for this service.
EXTERIOR AND INTERIOR LIGHTS
Item
Wattage (W)
Bulb No.
Headlight assembly*
High
—
—
Low
—
—
Park/ Daytime running
—
—
Turn
28/8
12V28/8W
Side marker
—
—
Front fog lights (if so equipped)*
—
—
Door mirror turn signal*
—
—
Map light*
—
—
Footwell light (if so equipped)*
—
—
Personal lights*
8
—
Step light*
5
168
Courtesy light*
—
—
Vanity mirror light (if so equipped)*
5
—
Cargo light*
8
—
Cargo door light*
5
—
High-mounted stop light*
—
—
Rear combination light*
Stop/Tail
—
—
Turn
21
WY21W
Side marker
5
W5W
Backup (reversing) assembly*
Tail
—
—
Backup
16
W16W
License plate light*
—
—
* It is recommended that you visit a NISSAN dealer for replacement.
LIGHTS
Do-it-yourself
8-27
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Always check with the Parts Department at
a NISSAN dealer for the latest parts
information.
1.
Headlight assembly
2
Map light
3.
Door mirror turn signal
4.
Step light
5.
Fog light (if so equipped)
6.
Personal light
7.
Cargo light
8.
High-mounted stop light
9.
Cargo door light
10.
License plate light
11.
Backup (reversing) assembly
12.
Rear combination light
Replacement procedures
All other lights are either type A, B, C or D.
When replacing a bulb, first remove the
lens, lamp and/or cover.
Indicates bulb removal
Indicates bulb installation
LDI3635
WDI0263
8-28
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
If you have a flat tire, see “Flat tire”
(P. 6-3).
TIRE PRESSURE
Tire Pressure Monitoring System
(TPMS)
WARNING
Radio waves could adversely af-
fect electric medical equipment.
Those who use a pacemaker
should contact the electric medi-
cal equipment manufacturer for
the possible influences before
use.
This vehicle is equipped with the Tire
Pressure Monitoring System (TPMS). It
monitors tire pressure of all tires ex-
cept the spare. When the low tire pres-
sure warning light is lit and the “Tire
Pressure Low - Add Air” warning ap-
pears in the vehicle information dis-
play, one or more of your tires is signifi-
cantly under-inflated. If equipped, the
system also displays pressure of all
tires (except the spare tire) on the dis-
play screen by sending a signal from a
sensor that is installed in each wheel.
The TPMS will activate only when the
vehicle is driven at speeds above 16
mph (25 km/h). Also, this system
may not detect a sudden drop in tire
pressure (for example a flat tire while
driving).
For additional information, see “Low
tire pressure warning light” (P. 2-18),
“Tire Pressure Monitoring System
(TPMS)” (P. 5-5) and “Flat tire” (P. 6-3).
Tire inflation pressure
Check the tire pressures (including
the spare) often and always prior to
long distance trips. The recom-
mended tire pressure specifications
are shown on the F.M.V.S.S./C.M.V.S.S.
certification label or the Tire and
Loading Information label under the
“Cold Tire Pressure” heading. The Tire
and Loading Information label is af-
fixed to the driver side center pillar.
Tire pressures should be checked
regularly because:
• Most tires naturally lose air over
time.
• Tires can lose air suddenly when
driven over potholes or other ob-
jects or if the vehicle strikes a curb
while parking.
The
tire
pressures
should
be
checked when the tires are cold. The
tires are considered COLD after the
vehicle has been parked for 3 or
more hours, or driven less than 1 mile
(1.6 km) at moderate speeds.
The TPMS with Easy-Fill Tire Alert
provides visual and audible signals
outside the vehicle for inflating tires
to the recommended COLD tire
pressure. For additional information,
see “TPMS with Easy-Fill Tire Alert”
(P. 5-8).
WHEELS AND TIRES
Do-it-yourself
8-29
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Incorrect tire pressure, including
under inflation, may adversely af-
fect tire life and vehicle handling.
WARNING
•
Improperly inflated tires can
fail suddenly and cause an
accident.
•
The Gross Vehicle Weight Rat-
ing (GVWR) is located on the
F.M.V.S.S./C.M.V.S.S.
certifica-
tion label. The vehicle weight
capacity is indicated on the Tire
and Loading Information label.
Do not load your vehicle be-
yond this capacity. Overload-
ing your vehicle may result in
reduced tire life, unsafe operat-
ing conditions due to prema-
ture tire failure, or unfavorable
handling characteristics and
could also lead to a serious ac-
cident. Loading beyond the
specified capacity may also re-
sult in failure of other vehicle
components.
•
Before taking a long trip, or
whenever
you
heavily
load
your vehicle, use a tire pressure
gauge to ensure that the tire
pressures are at the specified
level.
•
For additional information re-
garding tires, refer to “Impor-
tant Tire Safety Information”
(US) or “Tire Safety Informa-
tion” (Canada) in the Warranty
Information Booklet.
8-30
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Tire and Loading Information
label
䊊
1
Seating capacity: The maximum
number of occupants that can
be seated in the vehicle.
䊊
2
Original tire size: The size of the
tires originally installed on the ve-
hicle at the factory.
䊊
3
Cold tire pressure: Inflate the tires
to this pressure when the tires
are cold. Tires are considered
COLD after the vehicle has been
parked for 3 or more hours, or
driven less than 1 mile (1.6 km) at
moderate speeds. The recom-
mended cold tire inflation is set
by the manufacturer to provide
the best balance of tire wear, ve-
hicle handling, driveability, tire
noise, etc., up to the vehicle's
GVWR.
䊊
4
Tire size - see “Tire labeling”
(P. 8-34).
䊊
5
Spare tire size.
䊊
6
Vehicle load limit: see “Vehicle
loading information” (P. 10-15)
LDI2737
Do-it-yourself
8-31
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Checking tire pressure
WARNING
•
Driving at high speeds, 100 mph
(160 km/h) or higher sustained
where it is legal to do so, can
cause tires to have excessive
heat build up, which may result
in a tire failure causing loss of
control, crash, injuries or even
death. Some high-speed rated
tires require inflation pressure
adjustment for high-speed op-
eration. When speed limits and
road conditions allow vehicle
driving at high speeds, make
sure tires are rated to support
high speed operation, tires are in
optimal conditions and pressure
is adjusted to correct cold infla-
tion pressure for high speed
operation.
•
If your vehicle is equipped with
255/50R20 tire sizes, tires re-
quire adjustment to the infla-
tion pressure when driving the
vehicle at speeds of 100 mph
(160 km/h) or higher where it is
legal to do so. See recom-
mended tire inflation chart for
correct operating pressure.
•
After vehicle high speed opera-
tion has ended, readjust the tire
pressure to the recommended
cold inflation pressure. For addi-
tional information, see "Check-
ing tire pressure" (P. 8-32).
1. Remove the valve stem cap from
the tire.
LDI0393
8-32
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
2. Press
the
pressure
gauge
squarely onto the valve stem. Do
not press too hard or force the
valve stem sideways, or air will es-
cape. If the hissing sound of air
escaping from the tire is heard
while checking the pressure, re-
position the gauge to eliminate
this leakage.
3. Remove the gauge.
4. Read the tire pressure on the
gauge stem and compare to the
specification shown on the Tire
and Loading Information label.
5. Add air to the tire as needed. If too
much air is added, press the core
of the valve stem briefly with the
tip of the gauge stem to release
pressure. Recheck the pressure
and add or release air as needed.
6. Install the valve stem cap.
7. Check the pressure of all other
tires, including the spare.
8. Check the pressure when driving
the vehicle at speeds of 100 mph
(160 km/h) or higher where it is
legal to do so.
Size
Cold Tire Infla-
tion Pressure
Front and Rear
Original Tire:
255/50R20
35 psi, 240 kPa
Front and Rear
Original Tire:
255/60R18
33 psi, 230 kPa
Spare Tire:
T165/90D18
60 psi, 420 kPa
Recommended tire inflation pres-
sures at speeds of 100 mph (160
km/h) or higher where it is legal to
do so.
Size
Cold Tire Infla-
tion Pressure
Front and Rear
Original Tire:
255/50R20
36 psi, 250 kPa
Do-it-yourself
8-33
-------------------------------------------------------------------------------------------------------------------------------------------------------------
TIRE LABELING
Federal law requires tire manufac-
turers to place standardized infor-
mation on the sidewall of all tires.
This information identifies and de-
scribes the fundamental character-
istics of the tire and also provides the
Tire Identification Number (TIN) for
safety standard certification. The TIN
can be used to identify the tire in
case of a recall.
O
1
Tire size (example: P215/65R15
95H)
1. P: The “P” indicates the tire is de-
signed for passenger vehicles (not
all tires have this information).
2. Three-digit number (215): This
number gives the width in milli-
meters of the tire from sidewall
edge to sidewall edge.
3. Two-digit number (65): This num-
ber, known as the aspect ratio,
gives the tire's ratio of height to
width.
4. R: The “R” stands for radial.
5. Two-digit number (15): This num-
ber is the wheel or rim diameter in
inches.
WDI0394
Example
WDI0395
Example
8-34
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
6. Two- or three-digit number (95):
This number is the tire's load in-
dex. It is a measurement of how
much
weight
each
tire
can
support.
7. H: Tire speed rating. You should
not drive the vehicle faster than
the tire speed rating.
O
2
TIN (Tire Identification Number)
for a new tire (example: DOT XX XX
XXX XXXX)
1. DOT: Abbreviation for the “Depart-
ment
Of
Transportation”.
The
symbol can be placed above, be-
low or to the left or right of the Tire
Identification Number.
2. Two-digit code: Manufacturer's
identification mark.
3. Two-digit code: Tire size.
4. Three-digit code: Tire type code
(Optional).
5. Four
numbers
represent
the
week and year the tire was built.
For example, the numbers 3103
means the 31st week of 2003. If
these numbers are missing then
look on the other sidewall of the
tire.
LDI2786
Example
Do-it-yourself
8-35
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст