Qashqai J11. Road wheels & tires — part 2
TIRE PRESSURE MONITORING SYSTEM
WT-21
< WIRING DIAGRAM >
[WITH TPMS]
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
WIRING DIAGRAM
TIRE PRESSURE MONITORING SYSTEM
Wiring Diagram
INFOID:0000000010339518
JREWC0693GB
WT-22
< WIRING DIAGRAM >
[WITH TPMS]
TIRE PRESSURE MONITORING SYSTEM
JREWC0695GB
TIRE PRESSURE MONITORING SYSTEM
WT-23
< WIRING DIAGRAM >
[WITH TPMS]
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
JREWC0696GB
WT-24
< WIRING DIAGRAM >
[WITH TPMS]
TIRE PRESSURE MONITORING SYSTEM
JREWC0697GB
DIAGNOSIS AND REPAIR WORK FLOW
WT-25
< BASIC INSPECTION >
[WITH TPMS]
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Work Flow
INFOID:0000000010339519
OVERALL SEQUENCE
DETAILED FLOW
1.
INTERVIEW FROM THE CUSTOMER
Clarify customer complaints before inspection. First of all, perform an interview utilizing and reproduce the
symptom as well as fully understand it. Ask customer about his/her complaints carefully. Check symptoms by
driving vehicle with customer, if necessary.
JMEIA0239GB
WT-26
< BASIC INSPECTION >
[WITH TPMS]
DIAGNOSIS AND REPAIR WORK FLOW
CAUTION:
Customers are not professional. Never guess easily like “maybe the customer means that...,” or “
maybe the customer mentions this symptom”.
>> GO TO 2.
2.
CHECK LOW TIRE PRESSURE WARNING LAMP BULB
Check that low tire pressure warning lamp in combination meter turns ON when ignition switch is turned ON.
Does low tire pressure warning lamp turns ON?
YES
>> GO TO 3.
NO
>> Perform combination meter diagnosis. If combination meter is normal, perform configuration.
. And check low tire pressure warning lamp again.
3.
CHECK LOW TIRE PRESSURE WARNING LAMP STATES (1)
Check states of low tire pressure warning lamp in combination meter when ignition switch is turned ON.
How is states of low tire pressure warning lamp?
Stays ON>>GO TO 4.
Blinks for 1 minute and then stays ON>>GO TO 5.
Turns ON for 1 second and then stays OFF>>GO TO 6.
4.
CHECK AIR LEAK
Adjust the tire pressure for all wheels specified to the value. Refer to
And then check air leak using soapsuds etc..
NOTE:
Check valve core and around valve stem too.
Is air leak detected?
YES
>> Repair or replace error-detected parts. And then GO TO 8.
NO
>> GO TO 8.
5.
CHECK TIRE PRESSURE SENSOR INSTALLATION
Check visually that tire pressure sensors are installed to each wheels correctly.
NOTE:
In the following case, tire pressure monitoring system (TPMS) does not function.
• Tire pressure sensor(s) are not installed.
• Tire pressure sensor(s) of other cars are installed.
Are the genuine NISSAN tire pressure sensors are installed correctly?
YES
>> GO TO 9.
NO
>> GO TO 7.
6.
EXPLAIN TO THE CUSTOMER
Explain the following possibilities to the customer.
• When illuminating low tire pressure warning lamp went out:
- Tire pressure was lower than the warning tire pressure value.
• When blinking low tire pressure warning lamp went out:
- Radio waves of tire pressure sensor broke off temporarily by interference of other radio waves (e.g. radio
tower, battery charger of smart phone).
- Wheel(s) to which tire pressure sensor was not installed were attached.
NOTE:
Low tire pressure warning lamp turned off since malfunction was solved in any case.
Has the customer been convinced?
YES
>> INSPECTION END
NO
>> GO TO 9.
7.
REPLACING/INSTALLING TIRE PRESSURE SENSOR
1.
Replace and/or Install tire pressure sensor(s). Refer to
WT-62, "Removal and Installation"
2.
Perform tire pressure sensor ID registration. Refer to
.
Is tire pressure sensor ID registration completed?
YES
>> GO TO 8.
DIAGNOSIS AND REPAIR WORK FLOW
WT-27
< BASIC INSPECTION >
[WITH TPMS]
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
NO
>> Perform diagnosis procedure of “TIRE PRESSURE SENSOR ID REGISTRATION CANNOT BE
. And then GO TO 8.
8.
CHECK LOW TIRE PRESSURE WARNING LAMP STATES (2)
1.
Adjust the tire pressure for all wheels specified to the value. Refer to
.
2.
Perform TPMS temperature calibration. Refer to
WT-14, "TPMS temperature calibration"
.
3.
Check states of low tire pressure warning lamp in combination meter when ignition switch is turned ON.
Does low tire pressure warning lamp turn ON for 1 second and then turn OFF?
YES
>> Explain to the customer that this is TPMS normal operation, and GO TO 13.
NO
>> GO TO 9.
9.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “AIR PRESSURE MONITOR”.
Is DTC detected?
YES
>> Record or print self-diagnosis results and freeze frame data (FFD). GO TO 10.
NO
>> GO TO 11.
10.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
Perform DTC CONFIRMATION PROCEDURE for the detected DTC, and then check that DTC is detected
again.
Is DTC detected?
YES
>> GO TO 12.
NO
>> Check harness and connectors based on the information obtained by interview and repair or
replace error-detected parts. Refer to
GI-41, "Intermittent Incident"
. GO TO 13.
11.
CONFIRM THE SYMPTOM
Perform symptom diagnosis. refer to
>> Repair or replace error-detected parts. GO TO 13.
12.
DIAGNOSIS PROCEDURE
Perform DTC Diagnosis Procedure.
>> Repair or replace error-detected parts. GO TO 13.
13.
FINAL CHECK
Recheck the symptom and check that the symptom is not reproduced on the same conditions.
Is the symptom reproduced?
YES
>> GO TO 3.
NO
>> INSTPECTION END
WT-28
< BASIC INSPECTION >
[WITH TPMS]
ADDITIONAL SERVICE WHEN REPLACING BCM
ADDITIONAL SERVICE WHEN REPLACING BCM
Description
INFOID:0000000010339520
When replacing BCM, configuration (BCM, CAN gateway and TPMS) and then tire pressure sensor ID regis-
tration is required.
Work Procedure
INFOID:0000000010339521
1.
PERFORM CONFIGURATION (BCM)
Perform configuration BCM. Refer to
.
>> GO TO 2.
2.
PERFORM CONFIGURATION (CAN GATEWAY)
Perform configuration CAN gateway. Refer to
.
>> GO TO 3.
3.
PERFORM CONFIGURATION (TIRE PRESSURE MONITORING SYSTEM)
Perform configuration tire pressure monitoring system. Refer to
>> GO TO 4.
4.
PERFORM TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
.
>> WORK END
TIRE PRESSURE SENSOR ID REGISTRATION
WT-29
< BASIC INSPECTION >
[WITH TPMS]
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
TIRE PRESSURE SENSOR ID REGISTRATION
Description
INFOID:0000000010339522
This procedure must be performed:
• After replacement of a tire pressure sensor or BCM.
• After replacement of tire or road wheel.
NOTE:
ID registration is unnecessary if there are no change in the positions of each wheels (tire pressure sensors)
before wheel removal and after wheel installation.
• After performing tire rotation.
Work Procedure
INFOID:0000000010339523
1.
TIRE PRESSURE SENSOR ID REGISTRATION PROCEDURE
CAUTION:
To perform ID registration, observe the following points:
• Never register ID in a place where radio waves are interfered (e.g. radio tower).
• Never register ID in a place close to vehicles including TPMS.
NOTE:
Refer to the manufacture operating instructions for how to use the tire pressure sensor activation tool
[KV48105501 (NI-4032)].
With CONSULT
1.
Turn the ignition switch ON.
2.
Display the “WORK SUPPORT” screen and select “ID REGIST”.
3.
Select the start button on the “ID REGIST” screen.
4.
Contact the tire pressure sensor activation tool [KV48105501
(NI-4032)] (1) to the side of the tire at the location to the tire
pressure sensor.
5.
Press the registration button and wait until the hazard warning
lamp blinks twice.
CAUTION:
Perform the ID registration procedure starting from the
vehicle front left wheel, then repeat the procedure in the
order of the front right wheel, rear right wheel, and rear left
wheel.
6.
When ID registration is completed, check the following pattern at each wheel.
7.
After the ID registration procedure for all wheels is completed, press “End” to end ID registration, and
check that ID registration for all wheels is completed.
Is the check result normal?
YES
>> ID registration END.
NO
>> Refer to
.
NNEIC0020ZZ
Sequence
ID registration position
Turn signal lamp
CONSULT
1
Front left wheel
2 blinks
“Yet (red)”
↓
“Done (green)”
2
Front right wheel
3
Rear right wheel
4
Rear left wheel
WT-30
< BASIC INSPECTION >
[WITH TPMS]
CONFIGURATION (TIRE PRESSURE MONITORING SYSTEM)
CONFIGURATION (TIRE PRESSURE MONITORING SYSTEM)
Work Procedure
INFOID:0000000010339524
CAUTION:
• Use “Manual Configuration” only when “TYPE ID” of BCM cannot be read.
• After configuration, perform the following:
- Turn the ignition switch from OFF to ON and check that the low tire pressure warning lamp turns
OFF after staying illuminated for approximately two seconds.
- Perform tire pressure sensor ID registration. Refer to
• If an error occurs during configuration, start over from the beginning.
1.
CHECKING TYPE ID (1)
Use FAST (service parts catalogue) to search BCM of the parts number and find “Type ID”.
Is “Type ID” displayed?
YES
>> Print out “Type ID” and GO TO 2.
NO
>> “Configuration” is not required for BCM. Replace in the usual manner. Refer to
.
2.
CHECKING TYPE ID (2)
CONSULT Configuration
1.
Select “TPMS”
2.
Select “Before Replace ECU” of “Read/Write Configuration”.
3.
Check that “Type ID” is displayed on the CONSULT screen.
Is “Type ID” displayed?
YES
>> GO TO 3.
NO
>> GO TO 7.
3.
VERIFYING TYPE ID (1)
CONSULT Configuration
Compare a “Type ID” displayed on the CONSULT screen with the one searched by using FAST (service parts
catalogue) to check that these “Type ID” agree with each other.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.
>> GO TO 4.
4.
SAVING TYPE ID
CONSULT Configuration
Save “Type ID” on CONSULT.
>> GO TO 5.
5.
REPLACING BCM (1)
Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
>> GO TO 6.
6.
WRITING (AUTOMATIC WRITING)
CONSULT Configuration
1.
Select “After Replace ECU” of “Re/programming, Configuration” or that of “Read / Write Configuration”.
2.
Select the “Type ID” agreeing with the one stored on CONSULT and the one searched by using FAST
(service parts catalogue) to write the “Type ID” into the BCM.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.
>> GO TO 9.
CONFIGURATION (TIRE PRESSURE MONITORING SYSTEM)
WT-31
< BASIC INSPECTION >
[WITH TPMS]
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
7.
REPLACING BCM (2)
BCS-132, "Removal and Installation"
.
>> GO TO 8.
8.
WRITING (MANUAL WRITING)
CONSULT Configuration
1.
Select “Manual Configuration”.
2.
Select the “Type ID” searched by using FAST (service parts catalogue) to write the “Type ID” into the
BCM.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.
>> GO TO 9.
9.
VERIFYING TYPE ID (2)
Compare “Type ID” written into the BCM with the one searched by using FAST (service parts catalogue) to
check that these “Type ID” agree with each other.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.
>> GO TO 10.
10.
CHECKING LOW TIRE PRESSURE WARNING LAMP
1.
Turn the ignition switch OFF.
2.
Turn the ignition switch ON and check that the low tire pressure warning lamp turns OFF after staying illu-
minated for approximately two seconds.
CAUTION:
Never start the engine.
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> Perform the self-diagnosis of “AIR PRESSURE MONITOR”. Refer to
(TIRE PRESSURE MONITORING SYSTEM)"
11.
PERFORMING SUPPLEMENTARY WORK
1.
Adjust the tire pressure to the specified value. Refer to
.
2.
Perform tire pressure sensor ID registration. Refer to
.
3.
Perform the self-diagnosis of all systems.
4.
Erase self-diagnosis results.
5.
Perform TPMS temperature calibration. Refer to
WT-14, "TPMS temperature calibration"
.
>> End of work.
WT-32
< DTC/CIRCUIT DIAGNOSIS >
[WITH TPMS]
C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
DTC/CIRCUIT DIAGNOSIS
C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
DTC Description
INFOID:0000000010339525
DTC DETECTION LOGIC
NOTE:
The actual malfunction part may differ from the malfunction part which DTC shows if ID registration is not per-
formed after performing tire rotation or tire/road wheel replacement.
POSSIBLE CAUSE
• Low tire pressure (natural air leak)
• Air leak because of wheel change
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION
With CONSULT
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check the tire pressure for all wheels and adjust to the specified value. Refer to
.
3.
Perform TPMS temperature calibration. Refer to
WT-14, "TPMS temperature calibration"
.
4.
Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.
5.
Perform self-diagnosis for “AIR PRESSURE MONITOR”.
Is DTC “C1704”, “C1705”, “C1706”, or “C1707” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010339526
1.
TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
.
Is tire pressure sensor ID registration completed?
YES
>> GO TO 2.
NO
>> Replace applicable tire pressure sensor. Refer to
WT-62, "Removal and Installation"
2.
CHECK TIRE PRESSURE
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check the tire pressure of all wheels. Refer to
.
CAUTION:
If the checked value is close to the standard, reduce the tire pressure, and then with the ignition
switch ON, adjust the tire pressure again so that it is within the standard.
DTC No.
CONSULT screen item
(Trouble diagnosis content)
DTC Detection Condition
C1704
LOW PRESSURE FL
(Low tire pressure front left)
Front left tire pressure drops.
C1705
LOW PRESSURE FR
(Low tire pressure front right)
Front right tire pressure drops.
C1706
LOW PRESSURE RR
(Low tire pressure rear right)
Rear right tire pressure drops.
C1707
LOW PRESSURE RL
(Low tire pressure rear left)
Rear left tire pressure drops.
C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
WT-33
< DTC/CIRCUIT DIAGNOSIS >
[WITH TPMS]
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
3.
Perform TPMS temperature calibration. Refer to
WT-14, "TPMS temperature calibration"
.
4.
Drive for 2 minutes or more at a speed of between 25 km/h (16 MPH) and 100 km/h (62 MPH).
5.
Recheck the tire pressure of all wheels. Refer to
Is the inspection result normal?
YES
>> Perform “DTC CONFIRMATION PROCEDURE” (self-diagnosis) again. Refer to
.
NO
>> GO TO 3
3.
CHECK TIRE PRESSURE SIGNAL
With CONSULT
1.
Adjust tire pressure for all wheels to the specified value. Refer to
2.
Select “DATA MONITOR” in “AIR PRESSURE MONITOR”.
3.
Check that the tire pressures match the standard value.
Is the inspection result normal?
YES
>> Check air leak using soapsuds etc. and repair or replace error-detected parts. After erasing DTC
record, INSPECTION END.
NO
>> Repair or replace error-detected parts.
Monitor item
Displayed value
AIR PRESS FL
Approximately equal to the indication on tire gauge value for front left tire
AIR PRESS FR
Approximately equal to the indication on tire gauge value for front right tire
AIR PRESS RR
Approximately equal to the indication on tire gauge value for rear right tire
AIR PRESS RL
Approximately equal to the indication on tire gauge value for rear left tire
WT-34
< DTC/CIRCUIT DIAGNOSIS >
[WITH TPMS]
C1708, C1709, C1710, C1711 TIRE PRESSURE SENSOR
C1708, C1709, C1710, C1711 TIRE PRESSURE SENSOR
DTC Description
INFOID:0000000010339527
DTC DETECTION LOGIC
NOTE:
The actual malfunction part may differ from the malfunction part which DTC shows if ID registration is not per-
formed after performing tire rotation or tire/road wheel replacement.
POSSIBLE CAUSE
• BCM harness or connector
• BCM
• Tire pressure sensor ID registration incomplete
• Tire pressure sensor is not attached.
• Tire pressure sensor
• Tire pressure sensor battery voltage
• Driving in area where radio wave cannot be transmitted/received.
DTC CONFIRMATION PROCEDURE
1.
TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
.
Can the tire pressure sensor ID registration be completed?
YES
>> GO TO 2.
NO
>> Replace applicable tire pressure sensor. Refer to
WT-62, "Removal and Installation"
2.
PERFORM DTC CONFIRMATION
With CONSULT
1.
Drive the vehicle at 40 km/h (25 MPH) or more.
NOTE:
Avoid driving in area where radio wave cannot be transmitted/received.
2.
Stop the vehicle.
3.
Perform self-diagnosis for “AIR PRESSURE MONITOR”.
Is DTC “C1708”, “C1709”, “C1710” or “C1711” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010339528
1.
CHECK TIRE PRESSURE SIGNAL
With CONSULT
1.
Select “DATA MONITOR” in “AIR PRESSURE MONITOR”.
2.
Check the values that are displayed for “AIR PRESS FL”, “AIR PRESS FR”, “AIR PRESS RR”, and “AIR
PRESS RL”.
NOTE:
BCM holds last tire pressure values during 17 minutes after ignition switch turns OFF.
Are all tire pressures displayed 0 kPa (psi)?
DTC No.
CONSULT screen item
(Trouble diagnosis content)
DTC Detection Condition
C1708
[NO - DATA] - FL
(No data front left)
Tire pressure data signal from the front left wheel tire pressure sensor cannot be
detected.
C1709
[NO - DATA] - FR
(No data front right)
Tire pressure data signal from the front right wheel tire pressure sensor cannot
be detected.
C1710
[NO - DATA] - RR
(No data rear right)
Tire pressure data signal from the rear right wheel tire pressure sensor cannot be
detected.
C1711
[NO - DATA] - RL
(No data rear left)
Tire pressure data signal from the rear left wheel tire pressure sensor cannot be
detected.
C1708, C1709, C1710, C1711 TIRE PRESSURE SENSOR
WT-35
< DTC/CIRCUIT DIAGNOSIS >
[WITH TPMS]
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
YES
>> GO TO 2.
NO
>> Replace applicable tire pressure sensor. Refer to
WT-62, "Removal and Installation"
2.
TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
.
Can the tire pressure sensor ID registration be completed?
YES
>> GO TO 3.
NO
>> Replace applicable tire pressure sensor. Refer to
WT-62, "Removal and Installation"
3.
CHECK BCM POWER SUPPLY CIRCUIT
Check BCM power supply circuit. Refer to
BCS-125, "Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> Replace the BCM. Refer to
BCS-132, "Removal and Installation"
.
NO
>> Repair or replace harness or connectors.
WT-36
< DTC/CIRCUIT DIAGNOSIS >
[WITH TPMS]
C1716, C1717, C1718, C1719 TIRE PRESSURE SENSOR
C1716, C1717, C1718, C1719 TIRE PRESSURE SENSOR
DTC Description
INFOID:0000000010339529
DTC DETECTION LOGIC
NOTE:
The actual malfunction part may differ from the malfunction part which DTC shows if ID registration is not per-
formed after performing tire rotation or tire/road wheel replacement.
POSSIBLE CAUSE
• Tire pressure sensor
• BCM
DTC CONFIRMATION PROCEDURE
1.
PERFORM SELF DIAGNOSTIC RESULT
With CONSULT
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check tire pressure for all wheels and adjust to the specified value. Refer to
.
3.
Perform self-diagnosis for “AIR PRESSURE MONITOR”.
Is DTC C1716, C1717, C1718, or C1719 detected?
YES
>> Proceed to
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010339530
1.
TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
.
Can the tire pressure sensor ID registration be completed?
YES
>> Perform “DTC CONFIRMATION PROCEDURE” (self-diagnosis) again. Refer to
.
NO
>> Replace applicable tire pressure sensor. Refer to
WT-62, "Removal and Installation"
DTC No.
CONSULT screen item
(Trouble diagnosis content)
DTC Detection Condition
C1716
[PRESSDATA ERR] FL
(Pressure data error front left)
Malfunction in the tire pressure data from the front left wheel tire pressure sensor.
C1717
[PRESSDATA ERR] FR
(Pressure data error front right)
Malfunction in the tire pressure data from the front right wheel tire pressure sen-
sor.
C1718
[PRESSDATA ERR] RR
(Pressure data error rear right)
Malfunction in the tire pressure data from the rear right wheel tire pressure sen-
sor.
C1719
[PRESSDATA ERR] RL
(Pressure data error rear left)
Malfunction in the tire pressure data from the rear left wheel tire pressure sensor.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст