Nissan Note E12. Manual — part 401
INT-26
< REMOVAL AND INSTALLATION >
FLOOR TRIM
6. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to
"Removal and Installation (Battery)"
.
WARNING:
Before servicing the SRS, turn the ignition switch off, disconnect both battery terminals then wait
at least three minutes.
7. Disconnect the harness connector (A) from the seat belt retrac-
tor (1).
WARNING:
• Do not drop the seat belt retractor. Always handle it with
care.
• Always point pretensioner cylinder away from body when
handling.
CAUTION:
• For removing/installing the shoulder belt pre-tensioner
harness connector, insert a thin screwdriver wrapped in
tape into the notch, then lift the lock and remove the har-
ness connector as shown.
• Install the harness connector with the lock raised, and
push the lock into the harness connector as shown.
• After installing the harness connector, check that the lock
is pushed in securely.
8. Remove seat belt lower anchor bolt.
CAUTION:
Before removing the seat belt lower anchor bolt, note the positions of washers and spacers for
correct installation.
9. Remove diagnosis sensor unit. Refer to
SR-21, "Removal and Installation"
.
10. Remove shift selector. Refer to (5MT) or
TM-227, "Removal and Installation"
(CVT)
11. Remove A/C unit assembly bolt (C) and bracket (1) from vehicle.
12. Remove instrument panel lower bracket bolt (B) and screw (A)
and reposition bracket as necessary to remove floor trim.
ALHIA0316ZZ
PHIA0953J
ALJIA0712ZZ
FLOOR TRIM
INT-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
13. Release carpet hook clips with a suitable tool (A) and remove.
: Clip
14. Release pawls using a suitable tool (A) and open the harness
clips.
: Pawl
15. Remove floor trim.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Replace harness protector B with a new part after removal. Do not reuse harness protector B.
AWJIA0736ZZ
AWJIA0737ZZ
INT-28
< REMOVAL AND INSTALLATION >
HEADLINING
HEADLINING
Exploded View
INFOID:0000000009016050
1. Headlining
2. Rear assist grip (RH)
3. Front assist grip (RH)
4. Microphone (if equipped)
5. Sun visor holder (RH)
6. Sun visor holder (LH)
7. Map lamp (if equipped)
8. Sun visor (RH)
9. Sun visor (LH)
10. Interior room lamp
11. Rear assist grip (LH)
A. Headlining clip
Pawl
AWJIA1143ZZ
HEADLINING
INT-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Removal and Installation
INFOID:0000000009016051
REMOVAL
1. Remove front pillar finishers (LH/RH). Refer to
INT-19, "FRONT PILLAR FINISHER : Removal and Instal-
.
2. Remove sun visor screws and sun visorS (LH/RH).
3. Remove map lamp (if equipped). Refer to
INL-37, "Removal and Installation"
4. Remove interior room lamp. Refer to
INL-39, "Removal and Installation"
5. Remove microphone (if equipped). Refer to
AV-101, "Removal and Installation"
.
6. Remove center pillar upper finishers (LH/RH). Refer to
INT-23, "CENTER PILLAR UPPER FINISHER :
.
7. Remove luggage side upper finishers (LH/RH). Refer to
INT-33, "LUGGAGE SIDE UPPER FINISHER :
.
8. Insert a suitable tool (A) at approximately a 30 degree angle into
the sun visor holder notch on the front of the sun visor holder (1)
and press in the locking tab (B) to release it. While holding in
lock tab (B), rotate the sun visor holder (1) 90 degrees to release
it from the headlining.
: Front
CAUTION:
Do not force the sun visor holder when removing as the
locking tab may be damaged if the suitable tool is not posi-
tioned correctly.
NOTE:
If the sun visor holder (1) does not fully rotate, make sure that
the suitable tool (A) is pressing in on the locking tab (B) and is
not positioned under locking tab (B). Reinsert the suitable tool
(A) as necessary to release the locking tab (B).
9. Release assist grip pawls and remove bolt (A) using a suitable
tool and remove all assist grips.
:Pawl
10. Remove headlining clips.
11. Remove headlining through the back door.
CAUTION:
• Do not reuse headlining.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Remove all remaining adhesive from roof panel.
• Do not reuse headlining. Replace with new part after removal.
ALJIA0537ZZ
AWJIA1126ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст