Nissan Note E12. Manual — part 331
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FL-7
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
Remove the quick connector as follows:
• Hold the sides of the connector, push in tabs (B) and pull (A)
out the tube.
• If the connector and the tube are stuck together, push and pull
several times until they start to move. Then disconnect them
by pulling.
CAUTION:
• Quick connector (1) can be disconnected when the tabs
(F) are depressed completely. Do not twist it more than
necessary.
• Do not use any tools to disconnected quick connector.
• Keep resin tube (C) away from heat. Be especially careful
when welding near the resin tube.
• Prevent acid liquid such as battery electrolyte, etc. from
getting on resin tube.
• Do not bend or twist resin tube during installation and dis-
connection.
• Do not remove the remaining retainer (2) on hard tube (or
the equivalent) (A) except when resin tube or retainer is
replaced.
• When resin tube or hard tube (or the equivalent) is
replaced, also replace retainer with new one.
• To keep the connecting portion clean and to avoid dam-
age and foreign materials, cover them completely with
plastic bags (A) or something similar.
JPBIA0134ZZ
(B)
: Connection (cross-section)
(D)
: To under floor fuel line
(E)
: To fuel tank
(G)
: Disconnection
JPBIA0130ZZ
JPBIA0135ZZ
FL-8
< REMOVAL AND INSTALLATION >
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
8. Remove lock ring for fuel level sensor unit, fuel filter and fuel
pump assembly using Tool (A) by turning counterclockwise.
9. Remove fuel level sensor unit, fuel filter and fuel pump assembly.
CAUTION:
• Do not bend float arm during removal.
• Do not allow contaminants to fall inside of the fuel tank.
• Do not cause impacts such by dropping when handling components.
INSTALLATION
Installation is in the reverse order of removal.
• Install the fuel level sensor, fuel filter, and fuel pump assembly with
the fuel feed tube (C) facing the front of the vehicle as shown. Use
a new O-ring.
CAUTION:
Do not reuse O-ring.
• Connect the quick connector as follows:
- Check the connection for damage or any foreign materials.
- Align the connector with the tube, then insert the connector straight
into the tube until a click is heard.
• After the tube is connected, make sure the connection is secure by
performing the following checks:
- Pull (A) the tube and the connector to make sure they are securely
connected.
Tool number
: KV10119900 (J-45722)
ALBIA1059ZZ
: Front
(A)
: EVAP tube
(B)
: Harness connector
ALBIA1150ZZ
JPBIA0140ZZ
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FL-9
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
- Visually confirm that the two retainer tabs (F) are connected to the
quick connector (1).
Inspection
INFOID:0000000009445835
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leaks.
1. Turn ignition switch “ON” (with engine stopped), then check fuel system connections for leaks by applying
fuel pressure to fuel piping.
2. Start engine and let it idle and check there are no fuel leaks at the fuel system connections.
(B)
: Connection (cross-section)
(C) : Resin tube
(D) : To under floor fuel line
(E)
: To fuel tank
(G) : Disconnection
JPBIA0130ZZ
FL-10
< REMOVAL AND INSTALLATION >
FUEL TANK
FUEL TANK
Exploded View
INFOID:0000000009445836
Removal and Installation
INFOID:0000000009445837
WARNING:
Read “General Precautions” when working on the fuel system. Refer to
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Check the fuel level with the vehicle on a level surface. If the fuel
gauge indicates more than the level as shown (1/2 full), drain
the fuel from the fuel tank until the fuel gauge indicates a level at
or below as shown (1/2 full).
• In case the fuel pump does not operate, use the following pro-
cedure.
a. Disconnect the fuel filler hose from the fuel filler tube.
b. Insert fuel tubing of less than 20 mm (0.79 in) diameter into the
fuel filler tube through the fuel filler opening to drain fuel from the
fuel filler tube.
• As a guide, if the fuel tank is full the fuel level reaches or is
less than the level on the fuel gauge as shown, when approxi-
mately 20-1/2 (5-3/8 US gal, 4-1/2 Imp gal) of fuel is drained from a full fuel tank.
2. Release the fuel pressure from the fuel lines. Refer to
.
1.
Fuel tank
2.
Fuel tank mounting band (RH)
3.
Fuel tank mounting band (LH)
4.
Clamp
5.
Fuel filler hose
6.
Fuel filler tube
7.
Grommet
8.
Fuel filler cap
9.
Clamp
10. Vent hose
11.
EVAP vent line
AWBIA1594ZZ
ALBIA1130ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст