Nissan Note E12. Manual — part 140
DLK-64
< DTC/CIRCUIT DIAGNOSIS >
B2628 OUTSIDE ANTENNA
B2628 OUTSIDE ANTENNA
DTC Logic
INFOID:0000000009515844
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check Self Diagnostic Result mode of BCM using CONSULT.
Is outside key antenna DTC detected?
YES
>> Refer to
.
NO
>> Outside key antenna (rear bumper) is OK.
Diagnosis Procedure
INFOID:0000000009515845
Regarding Wiring Diagram information, refer to
DLK-37, "INTELLIGENT KEY SYSTEM : Wiring Diagram"
.
1.
CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 1
1. Turn ignition switch ON.
2. Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-67, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK OUTSIDE KEY ANTENNA CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector and outside key antenna (rear bumper) connector.
DTC
CONSULT display
description
DTC detecting condition
Possible cause
B2628
OUTSIDE ANTENNA
3
An excessive high or low voltage from outside key
antenna (rear bumper) is sent to BCM
• Outside key antenna (rear
bumper)
• Between BCM – Outside key an-
tenna (rear bumper)
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M98
82,83
Ground
When the back
door request
switch is operat-
ed with ignition
switch OFF
When Intelligent
Key is in the an-
tenna detection
area (The dis-
tance between
Intelligent Key
and antenna: 80
cm or less)
When Intelligent
Key is not in the
antenna detec-
tion area (The
distance be-
tween Intelli-
gent Key and
antenna: Ap-
prox. 2 m)
JMKIA5955GB
JMKIA5954GB
B2628 OUTSIDE ANTENNA
DLK-65
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3. Check continuity between BCM harness connector and outside key antenna (rear bumper) harness con-
nector.
4. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 2
1. Replace outside key antenna (rear bumper). (New antenna or other antenna)
2. Connect BCM and outside key antenna (rear bumper) connector.
3. Turn ignition switch ON.
4. Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace outside key antenna (rear bumper). Refer to
DLK-161, "REAR BUMPER : Removal and
NO
>> Replace BCM. Refer to
BCS-67, "Removal and Installation"
BCM
Outside key antenna (rear bumper)
Continuity
Connector
Terminal
Connector
Terminal
M98
82
B49
1
Yes
83
2
BCM
Ground
Continuity
Connector
Terminal
M98
82
No
83
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M98
82,83
Ground
When the back
door request
switch is operat-
ed with ignition
switch OFF
When Intelligent
Key is in the an-
tenna detection
area (The dis-
tance between
Intelligent Key
and antenna: 80
cm or less)
When Intelligent
Key is not in the
antenna detec-
tion area (The
distance be-
tween Intelli-
gent Key and
antenna: Ap-
prox. 2 m)
JMKIA5955GB
JMKIA5954GB
DLK-66
< DTC/CIRCUIT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000009567651
Regarding Wiring Diagram information, refer to
.
1.
CHECK FUSES AND FUSIBLE LINK
Check that the following fuses and fusible link are not blown.
Is the fuse blown?
YES
>> Replace the blown fuse or fusible link after repairing the affected circuit.
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT
1. Disconnect BCM connector M99.
2. Check voltage between BCM connector M99 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK GROUND CIRCUIT
Check continuity between BCM connector M99 and ground.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair harness or connector.
Terminal No.
Signal name
Fuses and fusible link No.
57
Battery power supply
12 (10A)
70
G (40A)
BCM
Ground
Voltage
Connector
Terminal
M99
57
—
Battery voltage
70
BCM
Ground
Continuity
Connector
Terminal
M99
67
—
Yes
COMBINATION METER BUZZER
DLK-67
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
COMBINATION METER BUZZER
Component Function Check
INFOID:0000000009515847
1.
CHECK FUNCTION
1. Select INTELLIGENT KEY of BCM using CONSULT.
2. Select INSIDE BUZZER in ACTIVE TEST mode.
3. Touch Key, Knob or Take Out to check that it works normally.
Is the inspection result normal?
Yes
>> Combination meter buzzer is OK.
No
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009515848
1.
CHECK METER BUZZER CIRCUIT
WCS-28, "Component Function Check"
.
Is the inspection result normal?
Yes
>> GO TO 2.
No
>> Repair or replace harness.
2.
CHECK INTERMITTENT INCIDENT
GI-41, "Intermittent Incident"
.
>> Inspection End.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст