Nissan Note E12. Manual — part 523
RSU-10
< REMOVAL AND INSTALLATION >
REAR SHOCK ABSORBER
Shock Absorber
Check the following items and replace the parts if necessary.
• Check the shock absorber for oil leaks, deformation, cracks, and other damage.
• Check the piston rod for damage, uneven wear, and distortion.
Bound Bumper, Bushing
Check for cracks and damage. Replace the parts if necessary.
Washer, Bound Bumper Cover, Distance Tube
• Check for cracks and damage. Replace the parts if necessary.
Disposal
INFOID:0000000009515816
1. Set the shock absorber horizontally with the piston rod fully extended.
2. Drill a 2 – 3 mm (0.08 – 0.12 in) hole at the position ( ) from the
top as shown to release gas gradually.
CAUTION:
• Wear eye protection (safety glasses).
• Wear gloves.
• Be careful with metal chips or oil blown out by the com-
pressed gas.
NOTE:
• Drill vertically in this direction (
).
• Drill directly to the outer tube avoiding brackets.
• The gas is clear, colorless, odorless, and harmless.
3. Position the drilled hole downward and drain oil by moving the piston rod several times.
CAUTION:
Dispose of drained oil according to the law and local regulations.
(A)
: 20 – 30 mm (0.79 – 1.18 in)
JPEIA0161ZZ
COIL SPRING
RSU-11
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
COIL SPRING
Exploded View
INFOID:0000000009515817
Removal and Installation
INFOID:0000000009515818
REMOVAL
1. Set a suitable jack under the rear suspension beam.
CAUTION:
• At this step, the jack must be set only for supporting the removal procedure. For details on jack-
ing up the vehicle, refer to
GI-28, "Garage Jack and Safety Stand"
• Do not damage the rear suspension beam with the jack.
2. Remove the lower shock absorber bolts. Refer to
3. Slowly lower the suitable jack. Remove the upper rubber seat, the coil spring, and the lower rubber seat
from the rear suspension beam.
CAUTION:
Make sure the rear suspension beam is stable when using the jack.
4. Inspect the components. Refer to
INSTALLATION
Installation is in the reverse order of removal.
• Identify the upper side of the coil spring.
NOTE:
The top of the coil spring has a flat shape.
1.
Upper rubber seat
2.
Coil spring
3.
Lower rubber seat
4.
Rear suspension beam
JPEIB0162ZZ
: Upper side
JSEIA0430ZZ
RSU-12
< REMOVAL AND INSTALLATION >
COIL SPRING
• Install the lower rubber seat (A) to the rear suspension beam
mounting hole (B).
• Match up lower rubber seat indentions and rear suspension beam
grooves and attach.
Inspection
INFOID:0000000009515819
INSPECTION AFTER REMOVAL
Check the upper rubber seat, the lower rubber seat, and the coil spring for deformation, cracks, and damage.
Replace the parts if necessary.
JPEIB0223ZZ
REAR SUSPENSION BEAM
RSU-13
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
REAR SUSPENSION BEAM
Exploded View
INFOID:0000000009592946
Removal and Installation
INFOID:0000000009592947
NOTE:
When removing components such as hoses, tubes, lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove the rear wheels and tires using power tools. Refer to
WT-8, "Removal and Installation"
.
2. Disconnect the brake hoses from the rear suspension beam.
3. Remove the spindles and rear drum brake components. Refer to
.
4. Remove the wheel sensors and position the wheel sensor harnesses aside. Refer to
5. Disconnect the parking brake cables from the rear suspension beam and position the rear drum brake
back plates aside with wire. Refer to
6. Set a suitable jack under the rear suspension beam.
CAUTION:
• At this step, the jack must be set only for supporting the removal procedure. For details on jack-
ing up the vehicle, refer to
GI-28, "Garage Jack and Safety Stand"
• Do not damage the rear suspension beam with the jack.
7. Remove the lower shock absorber bolts. Refer to
8. Slowly lower the suitable jack. Remove the upper rubber seats, the coil springs, and the lower rubber
seats from the rear suspension beam.
CAUTION:
Make sure the rear suspension beam is stable when using the jack.
9. Remove the rear suspension beam bolts.
10. Slowly lower the suitable jack. Remove the rear suspension beam from the vehicle.
11. Inspect the components. Refer to
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not reuse the rear suspension beam nuts.
1.
Rear suspension beam
AWEIA0323ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст