Nissan Note E12. Manual — part 572
FRONT PASSENGER AIR BAG MODULE
SR-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
FRONT PASSENGER AIR BAG MODULE
Exploded View
INFOID:0000000009015623
Removal and Installation
INFOID:0000000009015624
WARNING:
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals then wait at
least three minutes.
• Always work from the side of air bag module. Do not work in front of it.
• Do not expose the front passenger air bag module to temperatures exceeding 90
°C (194°F).
• Do not attempt to disassemble the front passenger air bag module.
• Do not insert any foreign objects (screwdriver, etc.) into the front passenger air bag module.
• Do not use air tools or electric tools for servicing.
CAUTION:
• Do not allow oil, grease, detergent, or water to come in contact with the front passenger air bag mod-
ule.
REMOVAL
1. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to
"Removal and Installation (Battery)"
.
2. Remove the glove box assembly. Refer to
IP-25, "Removal and Installation"
1.
Front passenger air bag module
2.
Instrument panel assembly
Pawl
AWHIA0529ZZ
SR-18
< REMOVAL AND INSTALLATION >
FRONT PASSENGER AIR BAG MODULE
3. Disconnect the harness connector (A) from front passenger air
bag module.
4. Remove and discard the front passenger air bag module bolts
(B).
CAUTION:
Do not reuse front passenger air bag module bolts.
5. Release pawls using a suitable tool and remove front passenger
air bag module (1).
: Pawl
CAUTION:
• Always place the front passenger air bag module with pad
side facing upward.
: Upward
• Do not strike the front passenger air bag module.
• Replace the front passenger air bag module if it has been
dropped or sustained an impact.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse the front passenger air bag module bolts.
• Do not damage the front passenger air bag module harness during installation.
• After the work is completed, perform diagnosis to check that no malfunction is detected. Refer to
.
JMHIA2022ZZ
AWHIA0527ZZ
JMHIA2461ZZ
JMHIA0009ZZ
CRASH ZONE SENSOR
SR-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
CRASH ZONE SENSOR
Exploded View
INFOID:0000000009486784
Removal and Installation
INFOID:0000000009486785
WARNING:
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals then wait at
least three minutes.
• Replace the crash zone sensor if it has been dropped or sustained an impact.
• Replace the crash zone sensor if either the driver air bag module, the front passenger air bag mod-
ule, or a front seat belt pre-tensioner has been deployed.
• Do not strike the crash zone sensor.
• Do not use air tools or electric tools for servicing.
REMOVAL
1. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to
"Removal and Installation (Battery)"
.
1. Crash zone sensor
2. Bracket
ALHIA0305ZZ
SR-20
< REMOVAL AND INSTALLATION >
CRASH ZONE SENSOR
2. Remove and discard crash zone sensor nut (A).
CAUTION:
Do not reuse crash zone sensor nut.
3. Remove bracket (1) and crash zone sensor (2).
4. Disconnect the slide double locking type harness connector from the crash zone sensor, as shown.
INSTALLATION
Installation is in the reverse order of removal.
Position the crash zone sensor using the locating pin before tightening the nut to specification.
CAUTION:
• Do not reuse the crash zone sensor nut.
• Do not damage the harness connector during installation.
• After the work is completed, perform diagnosis to check that no malfunction is detected. Refer to
.
ALHIA0306ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст