Nissan Note E12. Manual — part 126
DLK-8
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000009486705
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000009486706
Tool number
(Kent-Moore No.)
Tool name
Description
—
(J-39570)
Chassis Ear
Locating the noise
—
(J-50397)
NISSAN Squeak and Rat-
tle Kit
Repairing the cause of noise
—
(J-43241)
Remote Keyless Entry
Tester
Used to test keyfobs
—
(J-50190)
Signal Tech II
• Check Intelligent Key relative signal
strength
• Confirm vehicle Intelligent Key antenna
signal strength
—
(J-46534)
Trim Tool Set
Removing trim components
SIIA0993E
ALJIA1232ZZ
LEL946A
ALEIA0131ZZ
AWJIA0483ZZ
PREPARATION
DLK-9
< PREPARATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
(Kent-Moore No.)
Tool name
Description
(J-39565)
Engine Ear
Locating the noise
( — )
Power Tool
Loosening nuts, screws and bolts
SIIA0995E
PIIB1407E
DLK-10
< SYSTEM DESCRIPTION >
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
DOOR LOCK SYSTEM
DOOR LOCK SYSTEM : Component Parts Location
INFOID:0000000009015758
ALKIA3191ZZ
COMPONENT PARTS
DLK-11
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
A. View with instrument panel assembly
removed
B. View with glove box door removed
C. View with front grill removed
D. View of LH door. (RH similar)
E. View of LH door switch (RH similar)
F.
View with rear bumper cover re-
moved
G. View from rear of vehicle
H. View with rear seat cushion removed I.
View with center console removed
No.
Component
Function
1.
Combination meter
Combination meter transmits the vehicle speed sig-
nal to BCM via CAN communication.
BCM also receives the vehicle speed signal from
ABS actuator and electric unit (control unit) via CAN
communication. BCM compares both signals to de-
tect the vehicle speed.
Security indicator lamp is located on combination
meter.
Security indicator lamp blinks when ignition switch
is in any position other than ON to warn that NIS-
SAN VEHICLE IMMOBILIZER SYSTEM-NATS
[NVIS (NATS)] is on board.
Refer to
MWI-6, "METER SYSTEM : Combination
.
2.
Push-button ignition switch
Push-button ignition switch has push switch inside
which detects that push-button ignition switch is
pressed, and then transmits ON/OFF signal to
BCM. BCM changes the ignition switch position with
the operation of push-button ignition switch. BCM
maintains the ignition switch position status while
push-button ignition switch is not operated.
3.
BCM
BCM controls INTELLIGENT KEY SYSTEM (EN-
GINE START FUNCTION), NISSAN VEHICLE IM-
MOBILIZER SYSTEM-NATS [NVIS (NATS)] and
VEHICLE SECURITY SYSTEM.
BCM performs the ID verification between BCM and
Intelligent Key when the Intelligent Key is carried
into the detection area of inside key antenna, and
push-button ignition switch is pressed. If the ID ver-
ification result is OK, ignition switch operation is
available.
Then, when the ignition switch is turned ON, BCM
performs ID verification between BCM and ECM. If
the ID verification result is OK, ECM can start en-
gine.
Refer to
location.
4.
Main power window and door lock/unlock switch
Door lock and unlock switch is integrated into the
power window main switch.
Door lock and unlock switch transmits door lock/un-
lock operation signal to BCM.
Refer to
PWC-6, "Power Window Main Switch"
5.
Front door lock assembly LH
Door key cylinder switch is integrated into front door
lock assembly (driver side).
Door key cylinder switch detects door LOCK/UN-
LOCK operation using mechanical key, and then
transmits the operation signal to BCM.
Refer to
DLK-14, "DOOR LOCK SYSTEM : Front
Door Lock Assembly (Driver Side)"
.
6.
Rear door lock actuator LH
Rear door lock actuator locks/unlocks the rear door
latch assembly.
7.
Back door lock actuator
Back door lock actuator locks/unlocks the back door
latch assembly.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст