Nissan Note E12. Manual — part 95
WHEEL SENSOR
BRC-71
< REMOVAL AND INSTALLATION >
[ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
1. Remove bolts (A) and support bracket (1) (LH side only).
2. Disconnect the harness connector from the rear wheel sensor.
3. Release rear wheel sensor harness clips from the vehicle.
4. Remove bolts and rear wheel sensor from back plate.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not twist rear wheel sensor harness when installing rear
wheel sensor. Check that grommet (2) is fully inserted to
bracket (1). Check that rear wheel sensor harness is not twisted
after installation.
ALFIA0391ZZ
JPFIC0209ZZ
BRC-72
< REMOVAL AND INSTALLATION >
[ABS]
SENSOR ROTOR
SENSOR ROTOR
FRONT SENSOR ROTOR
FRONT SENSOR ROTOR : Removal and Installation
INFOID:0000000009619493
REMOVAL
Remove sensor rotor from steering knuckle. Refer to
.
INSTALLATION
Installation is in the reverse order of removal.
REAR SENSOR ROTOR
REAR SENSOR ROTOR : Removal and Installation
INFOID:0000000009619494
REMOVAL
Remove sensor rotor from brake drum. Refer to
.
CAUTION:
Do not reuse rear sensor rotor.
INSTALLATION
Installation is in the reverse order of removal.
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
BRC-73
< REMOVAL AND INSTALLATION >
[ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Exploded View
INFOID:0000000009619495
Removal and Installation
INFOID:0000000009619496
REMOVAL
CAUTION:
• Before servicing, disconnect the battery cable from negative terminal.
• Do not remove acuator by holding harness.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1. Disconnect negative battery cable. Refer to
PG-69, "Removal and Installation (Battery)"
.
2. Disconnect vacuum hose from intake manifold. Refer to
1.
ABS actuator and electric unit (con-
trol unit)
2.
ABS actuator and electric unit (con-
trol unit) harness connector
3.
Bracket
4.
Bushing
5.
Insulating clip
6.
Bolt
A.
To master cylinder secondary side
B.
To rear brake tube (RH)
C.
To front brake tube (LH)
D.
To front brake tube (RH)
E.
To rear brake tube (LH)
F.
To master cylinder primary side
AWFIA1025ZZ
BRC-74
< REMOVAL AND INSTALLATION >
[ABS]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
3. Remove ground harness bolt (A) and ground harness from radi-
ator core support.
4. Disconnect high-pressure pipe from expansion valve. Refer to
.
CAUTION:
Cap or wrap the joint of the A/C piping and expansion valve with suitable material such as vinyl
tape to avoid the entry of air.
5. Remove low-pressure flexible hose. Refer to
HA-27, "LOW-PRESSURE FLEXIBLE HOSE : Removal and
.
6. Loosen flare nut from brake tubes using a flare nut wrench, then remove brake tubes from ABS actuator
and electric unit (control unit). Refer to
BR-21, "FRONT : Exploded View"
7. Disconnect the harness connector from the ABS actuator and electric unit (control unit).
8. Remove ABS actuator and electric unit (control unit) bracket bolts.
9. Remove the ABS actuator and electric unit (control unit) and bracket as an assembly.
10. Remove bracket and bushing from ABS actuator and electric unit (if necessary).
INSTALLATION
Installation is in the reverse order of removal.
• Bleed the brake system. Refer to
BR-12, "Bleeding Brake System"
CAUTION:
• Replace the ABS actuator and electric until (control unit) if it has been dropped or sustained an
impact.
• Do not install actuator by holding harness.
• After installing harness connector in the ABS actuator and electric unit (control unit), make sure har-
ness connector is securely locked.
ALKIA3174ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст